National Institute Of Materials Physics - Romania

Undoped and Sm3+doped 45P2O5-45Na2O-2Al2O3-8BaO glasses were synthesized by the melt-quenching technique. The glass structure and luminescence properties were investigated by using Raman spectroscopy, scanning electron microscopy (SEM), spectroscopic ellipsometry, Judd-Ofelt theory and photoluminescence. Electron microscopy showed the homogeneity of samples. Raman spectroscopy revealed that the overall struc-ture of the glass was unaffected by the doping of Sm3+ and ellipsometry was used to measure the optical constants. Judd-Ofelt (JO) analysis was performed on the absorption bands of Sm3+ (4f5) and the three phenomenological parameters (omega 2, omega 4, and omega 6) were computed and then used to determine radiative properties such as the radiative transition probability (Ar), the fluorescent branching ratio (beta r), the stimulated emission cross-section (sigma e) and the radiative lifetime (tau rad). Photoluminescence (PL) spectrum showed the typical four transitions of Sm3+ at wavelengths of 564, 600, 645 and 703 nm corresponding to 4G5/2 -> 6H5/2, 6H7/2, 6H9/2 and 6H11/2, respectively. The spectroscopic quality factors omega 4/omega 6, the predicted lifetime (tau rad) calculated using the JO method and the experimentally lifetime (tau exp) for the 4G5/2level were calculated and discussed. The glass color purity is as high as 98%, which makes it a potential candidate for laser emission.

This is the first report on an efficient, "environmentally friendly" chemical reduction method for the synthesis of aminated hyaluronic acid-based silver nanoparticles on the modified surface of titanium dioxide nanoparticles aimed for biological applications. Silver nanoparticles exhibit well-known physical-chemical and optical prop-erties appropriate for different biological applications. Modifying the nanoparticles leads to a change in their expected bioactivity. This represents an important topic for the current research. We have developed a novel aminated hyaluronic acid (HA-EDA)-based protocol to obtain silver nanoparticles, in which HA-EDA was used for the first time as a reducing and stabilizing agent. The effect of the size of silver nanoparticles on the titanium dioxide surface and the chemical composition of the obtained materials were investigated by TEM, XRD, XPS, ATR-FTIR, Raman spectroscopy, NMR and H2-TPR analyses. The antioxidant, in vitro biocompatibility, and antimicrobial activity of the fabricated composites have been evaluated. The results prove that the prepared materials exhibit antimicrobial, antioxidant, and anti-inflammatory activity, thus providing protection against infection and supporting tissue regeneration, these two key effects being of paramount importance for promoting wound healing.

Nanoscale Al-doped yttrium-iron garnets attract enhanced scientific and practical interest in the development of microwave devices due to their remarkable physical-chemical properties, which depend essentially on the method and conditions of synthesis. This work highlights the advantages of a specific two-stage synthesis of Y3AlFe4O12 garnet ferrite nanoparticles by the precipitation in aqueous solutions and deals with the detailed examinations of the precipitates obtained during this process. The results of the complex studies using high resolution transmission microscopy, dynamic light scattering and magnetic measurements have allowed assessing the features of the formation of crystalline structure. It is demonstrated that the sequence of the precipitation of components during the synthesis strongly affects the physical-chemical properties of the formed precipitate (filtration coefficient value, surface charge, micelle's structure) as well as the physical properties of nanoparticles obtained after their heat treatment at 800 degrees C (saturation magnetization, coercive force). Simultaneous precipitation of Fe(OH)3 and Al(OH)3 metal hydroxides, which form one of three crystallographic sub lattices of the garnet structure, at the first stage of the synthesis of ferrite-garnets is revealed to provide higher values of filtration coefficient of the formed precipitate and better technological and physical-chemical parameters of the fabricated garnet nanoparticles that makes this method highly advantageous for industrial application.

Two hybrid materials, based on 7-amino-4-(trifluoromethyl)coumarin and 7-amino-4-methyl-coumarin that attach covalently to graphene oxide (GO) have been synthesized in two steps: i) increasing the number of carboxyl groups required for functionalization with aminocoumarin derivatives by derivatization of the hydroxyls groups with chloroacetic acid, transforming GO into GO-COOH material; ii) activation of carboxylic groups using the carbodiimide-promoted reaction. The obtained composites were characterized by numerous methods that highlighted their successful obtaining. The antimicrobial activity was evaluated on resistant Mycobacterium tuberculosis strains, as well as on ESKAPE pathogens ((Enterococcus faecium, Staphylococcus aureus, Klebsiella pneumoniae, Acinetobacter baumannii, Pseudomonas aeruginosa, and Enterobacter spp.) in planktonic and biofilm growth states. The biocompatibility of the materials has been assayed using 3-(4, 5-dimethylthiazol-2-yl)2, 5-diphenyltetrazolium bromide assay as well as by measuring the level of nitric oxide/total reactive oxygen species and superoxide release in treated cells. The results have shown that materials exhibited improved inhibitory activity against resistant M. tuberculosis strains in comparison with GO, but also against planktonic and adherent strains. Also, the tested composites have been proved to be biocompatible on the MRC-5 fibroblast cells, demonstrating their promising potential to develop novel agents effective against multidrug resistant pathogens, including M. tuberculosis, as well as by the activation of a pro-inflammatory and of an oxidative response in the mammalian cells.

This study focused on investigating the optoelectronic properties of molybdenum trioxide (alpha-MoO3) thin films using the atomic layer deposition (ALD) technique through different cycle numbers and theoretical investigation. Initial band gap calculations using standard DFT with GGA-PBE resulted in a value of 1.19 eV, which deviated significantly from experimental measurements. The GGA + U method with Hubbard U corrections was applied for the first time to improve the accuracy. This refinement led to a more precise band gap value of 3.09 eV, closely matching previously reported experimental data. The electronic parameters of the alpha-MoO3 photodetector, such as ideality factor (n), barrier height (phi 0), and series resistance (Rs), were analyzed using the thermionic emission theory and confirmed by Cheung and Nord's methods. The results demonstrated that the sample deposited with 100 pulses exhibited higher photodetector performance under UV illumination, despite having a lower Rs.

High density samples (92-94.5 %) of MgB2 were prepared by Spark Plasma Sintering (SPS). The on-off pulsed current patterns of SPS processing were 8-4, 12-2, 24-2, 99-1. Patterns with more on pulses favor formation of a higher amount of the secondary MgB4 phase through the decomposition of MgB2. They also promote enhancement of larger MgO crystallites without a strong increase in the amount of this phase. Densification rate and pressure in the SPS chamber show a similar behavior, but their amplitude varies and the temperatures defining different stages present some shifts. As-revealed differences induced by pulsed patterns impact superconducting properties in a complex manner. An attempt to assess correlations between the pattern and different superconducting parameters is presented.

Hydrothermally formed mesoporous SnO2 was used as a support for nickel chemical deposition and, after subsequent thermal treatment, a high specific surface area (36 m(2) g(-1)) Ni/SnO2 material was obtained. XPS analysis has shown that in the Sn 3d region the spectrum is similar to that of pristine SnO2, whereas Ni species are present on the surface as NiO, Ni2O3 and Ni(OH)(2). Mixing Ni/SnO2 with a small amount of Black Pearls (BP) leads to a significant enhancement of the resulting Ni/SnO2-BP composite activity for nitrite anodic oxidation, presumably due to the higher surface area (115 m(2) g(-1)), to better electrical conductivity and to a certain contribution of the BP to an increase in surface density of the active sites. Ni/SnO2-BP also outperforms pristine BP (in terms of Tafel slopes and electron-transfer rates), most likely due to the fact that the Ni(ii)/Ni(iii) couple can act as an electrocatalyst for nitrite oxidation. A voltammetric method is proposed for the determination of nitrite, over a concentration range of three orders of magnitude (0.05 to 20 mM), with good reproducibility, high stability and excellent sensitivity. The high upper limit of the dynamic range of the analytically useful response might provide a basis for the reliable quantification of nitrite in wastewater.

B doped as well as B and N co-doped highly reduced graphene oxide and multiwall carbon nanotubes/Ni oxide and Ni hydroxide nanohybrid layers were synthesized using a one-step laser technique. NiO nanoparticles, graphene oxide platelets, and multiwall carbon nanotubes were used as starting materials for the preparation of the composite layers. H3BO3 was used as B precursor and urea as well as NH3 as N precursors for B and N co -doping of the composite layers. The influence of the nature and concentration of the B and N precursors on the physico-chemical properties of the nanohybrid layers, chemical composition and chemical bonding states, crystalline structure, as well as charge transfer properties was systematically investigated. The relation between the physico-chemical properties and functional characteristics of the nanohybrid layers, photocatalytic removal of water contaminants under simulated sun irradiation conditions was studied, identifying the optimum con-centrations of the dopant precursor materials. The mechanism of the photodegradation process was explored, based of the band structure of the composites. The main intermediates, reactive oxygen species implied in the photocatalytic degradation processes of organic molecules, was investigated through the addition of scavengers to the organic dye test solutions. The highest photocatalytic activities were achieved for B and N co-doped samples synthesised using H3BO3 as B and urea as N precursors.

The development of new synthetic methods is paramount for the versatile production of complex multicompo-nent electrodes for supercapacitors with enhanced performance. The reactive inverse matrix assisted pulsed laser evaporation (RIMAPLE) technique shows promise for the deposition of complex functional nanocomposites in a facile way. In this work, hybrid supercapacitor electrodes constituted by reduced graphene oxide (rGO) and carbon nanotubes (CNTs) decorated with a myriad of cerium and manganese oxide nanoparticles were obtained by using GO sheets, CNTs, CeO2 nanoparticles and, for the first time, the (NH4)2[Mn2(C6H5O7)2(H2O)2] coor-dination compound as precursors in the RIMAPLE targets. Compositional and structural characterizations revealed that post-annealing treatments at mild conditions (150-250 degrees C) induce a further reduction of the rGO and CNTs, besides an oxidation of the Ce oxide phases (Ce3+ to Ce4+) and a reduction of the Mn oxides (Mn3+ to Mn2+). The substantial change of the carbon and metal oxide nanostructures causes an up to 8-fold increase of the capacitance of the electrodes (63 F/cm3 @ 10 mV/s). Finally, the generation of a high quantity of edge defects at 250 degrees C and long dwell time leads to the drop of the electrode's capacitance.

Dielectric spectroscopy is a well-known method to characterize different liquid or solid (nano) materials such as liquid crystals, polymers, composites, ceramics etc. More the material structure is complex, more the molecular dynamics are put in evidence with difficulty. In many such cases, the analysis of the spectra with the classic Havriliak-Negami (H-N) functions is hard to apply or even fails. Therefore, we propose a simple numerical approach (with two different procedures) for the deconvolution of complex spectra in dielectric spectroscopy (DS). The final goal is to obtain the frequency of maximum loss (fmax) depending on the temperatures, Arrhenius diagram, and the activation energy/energies. The developed procedures have as their starting point the "logarithmic derivative of the permittivity". To our knowledge, these procedures have not yet been presented in the literature. The proposed first numerical processing allows a better separation of the different relaxation processes, a decrease in the contribution of the electrical conductivity and a better localization of the frequencies where the dielectric loss has maximum values. The second of the procedures is applied in certain particular situations, and the other procedure is more general. Where the former can be applied, it is equivalent to using the classical H-N functions in terms of obtaining the fmax, but it is simpler to apply. The first procedure uses an "artificial" and simpler H-N function, in which the fewer fitting parameters have no physical meaning, but allow a good localization of the frequency of maximum dielectric loss. The proposed procedure was applied on experimental data of dielectric spectroscopy obtained on pristine materials (nematic mixture E7 and ZnO) and composites E7-ZnO, obtained by a "green technology". The complicated spectra of the dielectric permittivity presented by these samples represent the suitable test to highlight the advantages but also the limitations of our approach. Comparing the values of the activation energy obtained for the two procedures is the criterion for verifying their correctness. The volume of processed experimental data is large, for this reason we present only the results obtained based on numerical approaches. The differences between the results obtained with the two procedures are small. The procedures can be considered as alternatives to the application of fitting with H-N functions. One procedure replaces H-N by eliminating the use of functions with complex variables and the method of least squares and has the advantage that it can apply non-specialized software like Origin. The other allows a better analysis of spectra being an improved-modified H-N approach. Proposed procedures are