National Institute Of Materials Physics - Romania

The particle reinforcement of fusion-relevant tungsten through the incorporation of tungsten sub-carbide W2C particles at the grain boundaries is demonstrated as an effective way of eliminating the harmful W oxide, enhancing densification and stabilising the composite's microstructure and flexural strength at room and high temperatures. The W2C particles are formed in situ during the sintering by carbon diffusion from WC nano-particles added as a precursor to the W matrix. Even in an extremely fast sintering process using Field-Assisted Sintering Technology (FAST, 1900 degrees C, 5 min), the added WC completely transforms to W2C, resulting in a W-W2C composite. While at least 5 vol % of WC nanoparticles are needed to eliminate the oxide, approximately 10 vol % result in a W-W2C composite with favourable characteristics: high density, high flexural strength at RT (>1200 MPa) as well as at elevated temperatures, and high thermal conductivity, which remains above 100 W/mK up to 1000 degrees C.

Magnetic Fe@Y composites (carbon-coated magnetic iron nanoparticles incorporated in zeolite Y) with 5-8 wt % Fe were synthesized and characterized. Overall acidity of the samples ranged between 2.0 and 2.47 mmol/g and is mostly attributed to Lewis acid sites. The obtained materials were proven to catalyze the hydrolysis of the marine sulfated polysaccharide ulvan with high conversion rates. The distribution of the reaction products depended on the reaction conditions and the concentration of ulvan. The catalytic property catalytic performance correlations clearly showed that the acid zeolite Y is the active phase for the hydrolysis of ulvan, while the iron nanoparticles enable the catalyst separation in a magnetic field. Under oxygen pressure, the selectivity was completely changed to favor succinic acid production. All Fe@Y composites were recycled 10 times with no change in their catalytic performance after recovery via a simple magnetic separation and washing with water.

Magnetic iron oxides have been used in biomedical applications, such as contrast agents for magnetic resonance imaging, carriers for controlled drug delivery and immunoassays, or magnetic hyperthermia for the past 40 years. Our aim is to investigate the effect of pressure and temperature on the structural, thermal, and magnetic properties of iron oxides prepared by hydrothermal synthesis at temperatures of 100-200 degrees C and pressures of 20-1000 bar. It has been found that pressure influences the type of iron oxide crystalline phase. Thus, the results obtained by Mossbauer characterization are in excellent agreement with X-ray diffraction and optical microscopy characterization, showing that, for lower pressure values (<100 bar), hematite is formed, while, at pressures >100 bar, the major crystalline phase is goethite. In addition, thermal analysis results are consistent with particle size analysis by X-ray diffraction, confirming the crystallization of the synthesized iron oxides. One order of magnitude higher magnetization has been obtained for sample synthesized at 1000 bar. The same sample provides after annealing treatment, the highest amount of good quality magnetite leading to a magnetization at saturation of 30 emu/g and a coercive field of 1000 Oe at 10 K and 450 Oe at 300 K, convenient for various applications.

A study on clay mineral polymer nanocomposites (CPN), namely polyaniline/montmorillonite-cetyltrimethylammonium bromide (PANI/Mt-CTAB), poly o-anisidine/montmorillonite-cetyltrimethylammonium bromide (poly(o-ANIS)/Mt-CTAB) and poly o-anisidine-co-aniline/montmorillonite-cetyltrimethylammonium bromide (poly(o-ANIS-co-ANI)/Mt-CTAB), synthesized by oxidative chemical polymerization method is presented. The nanocomposites have been characterized by Fourier transform infrared spectroscopy, UV-vis spectroscopy, and cyclic voltammetry, X-ray diffraction, scanning electron microscopy, transmission electron microscopy, cyclic voltammetry and thermogravimetry and differential scanning calorimetry analysis. By UV-vis measurements different electronic transitions for the CPNs were pointed out. The voltammograms indicate that the synthetized materials are electroactive. The FTIR analysis reveals the characteristic bands of the polymers and of the Mt-CTAB. The shift of the bands to higher/lower wavenumbers demonstrate the interaction between the pristine polymers macromolecular chains and the montmorillonite (Mt). The intercalation of the polymers inside the mineral clay was confirmed by the increased interlayer distance connected with the position of the 011 diffraction plane of the Mt., and the intercalation and exfoliation states were highlighted in the scanning and transmission electron microscopy images. The obtained results are encouraging in respect with the purpose to use them in the field of photovoltaic applications.

This work reports the effect of the Mn substitution, rapid solidification technique and heat treatments on the martensitic transformation, magnetic and magnetostrictive properties on the Fe70-xPd30Mnx (x = 1, 3) ferromagnetic shape memory ribbons. The samples were investigated by X-ray diffraction, differential scanning calorimetry, scanning electron microscopy, magnetic and magnetostrictive measurements. The thermal treatments induce significant changes in the microstructure and magnetocrystalline anisotropy of the martensitic phase, for Fe67Pd30Mn3 compared to Fe69Pd30Mn1. The competition between the magnetization orientation and twin boundary motion within martensitic variants under magnetic field evidenced in the magnetic-strain curves was discussed and correlated with the magnetic data.

MgB2 bulk superconductors are expected to be utilized as rare-earth-free and lightweight trapped field magnets. However, the flux jumps frequently happen during the magnetizing processes, and heavily degrade the field-trapping performances. We have investigated the effect of additives to the MgB2 bulk samples prepared by spark plasma sintering process, and observed various flux jumps during the pulsed field magnetizing processes, which were carried out at 14 K which was obtained by the 2-stage GM cryocooler. The authors classified the flux motions as three categories as "no flux flow", "fast flux flow", and "flux jump" regions, and investigated the conditions where the flux jumps happen. We observed some drastic flux jumps in the pristine and clarified the effect of graphene addition to the flux jumps. The experimental results showed us a possible expansion of no flux jump region, and suggested us the improvement of field trapping capability.

Indium-doped tin oxide (ITO) thin films were fabricated by radio frequency magnetron sputtering and were subjected to in-situ and ex-situ annealing, at 200 degrees C, 300 degrees C and 400 degrees C, respectively. The in-situ thermal treatment consisted to intentionally heating the samples' substrates, while the ex-situ annealing was performed using an oven, under ambient atmosphere. For the ITO samples subjected to ex-situ annealing, the density of oxygen vacancies increased leading to the decrease of the electrical resistivity. No significant changes were noticed in terms of transmission spectroscopy after the thermal treatment; while by evaluating the Skewness parameter was determined that the annealing improves the planarity of samples' surface.

Dense samples (94-96%) with starting composition (MgB2)(0.99)(X-acac)(0.01) (X-acac denotes Ga or In acetylacetonate) were obtained by spark plasma sintering. The resulting material is a superconducting composite, where carbon substitutes for boron in the crystal structure of MgB2. Added samples show enhanced critical current density at high magnetic fields and this is reflected in high values of irreversibility field (H-irr) at temperatures below 25 K when compared to a pristine sample. More efficient is In-acac addition and it promotes a H-irr of similar to 12.4T (100 A/cm(2) criterion) at 5 K. Carbon substitution for boron in the crystal structure of MgB2 has a strong influence on the pinning force and its related parameters and promotes in the added samples a grain boundary pinning mechanism as the dominant one, whereas the pristine sample with a low amount of carbon shows a major mechanism of point pinning type. However, our analysis indicates on the synergetic effects of the carbon substituting for boron and of the microstructural details on pinning and critical current density. The result strongly emphasizes the significantly different behavior of the additive during processing of the MgB2 samples, although thermal analysis experiments on both additives show very similar decomposition patterns. (C) 2020 The Authors. Published by Elsevier B.V.

MgB2 has great potential for many applications, thanks to its relatively high critical temperature and low fabrication cost. Large efforts are done to improve the current carrying capabilities of bulks and tapes in view of different application fields, e.g. with the addition of Te and cubic-BN to MgB2. To elucidate the vortex pinning physics exploiting a different dynamic regime, we present here a microwave study of the pinning properties of spark plasma sintered bulk MgB2 with and without the addition of 0.01 % at. Te or cubic-BN. We show the surface resistance R-s of the MgB2 samples measured with a dielectric-loaded resonator at similar to 16.5 GHz and similar to 26.7 GHz in the 10 K-Tc temperature range at fields up to 1.0 T. Then, the MgB2 R., is studied with high frequency vortex motion models in order to obtain the pinning constant (Labusch parameter) and the depinning frequency. Finally, the microwave behavior of MgB2 in the mixed state is compared with the recent results obtained on Nb3Sn.

Mixtures of B4C, alpha-AlB12 and B powders were reactively spark plasma sintered at 1800 degrees C. Crystalline and amorphous boron powders were used. Samples were tested for their impact behavior by the Split Hopkinson Pressure Bar method. When the ratio R = B4C/alpha-AlB12 >= 1.3 for a constant B-amount, the major phase in the samples was the orthorhombic AlB24C4, and when R < 1 the amount of AlB24C4 significantly decreased. Predictions that AlB24C4 has the best mechanical impact properties since it is the most compact and close to the ideal cubic packing among the Al-B-C phases containing B-12-type icosahedra were partially confirmed. Namely, the highest values of the Vickers hardness (32.4 GPa), dynamic strength (1323 MPa), strain and toughness were determined for the samples with R = 1.3, i.e., for the samples with a high amount of AlB24C4. However, the existence of a maximum, detectable especially in the dynamic strength vs. R, indicated the additional influence of the phases and the composite's microstructure in the samples. The type of boron does not influence the dependencies of the indicated mechanical parameters with R, but the curves are shifted to slightly higher values for the samples in which amorphous boron was used.