National Institute Of Materials Physics - Romania

In this work, the structural, thermal, vibrational, morphological, magnetic and optical properties of LaPO4:Ce/RE/Me (RE=Nd3+, Tb3+; Me-Cr3+, Mn2+) and LaPO4:Yb3+/Er3+ phosphors prepared by the co-precipitation method are presented. The obtained materials crystallized in monoclinic structure with the P2(1)/n space group and the particles were of nanorod shape with about 200 nm in length and the diameter approximately 19 nm. The presence of dopant ions was confirmed by both electron paramagnetic resonance (EPR) and UV-visible spectroscopies. In addition, the down-conversion (DC) and up-conversion (UC) of the LaPO4 nanophosphors via the 275 and 980 nm excitations, respectively, were considered, and a wide range of electronic transitions was observed. Based on the photoluminescence (PL) spectra, there is an efficient energy transfer (ET) process from Ce3+ donors to Nd3+ and Tb3+ acceptors, and the computed ET efficiency was 70% and 88%, respectively. The Ce3+/Cr3+ and Ce3+/Mn2+ doped LaPO4 showed weak far-red and green luminescence with much smaller ET efficiency of about 3.7 and 0.4%, respectively. LaPO4:Yb3+/Er3+ showed UC luminescence under the 980 nm laser radiation, and the resulted red and green light was attributed to the Er3+ transitions.

This study presents the design and manufacture of metasurface lenses optimized for focusing light with 1.55 mu m wavelength. The lenses are fabricated on silicon substrates using electron beam lithography, ultraviolet-nanoimprint lithography and cryogenic deep reactive-ion etching techniques. The designed metasurface makes use of the geometrical phase principle and consists of rectangular pillars with target dimensions of height h = 1200 nm, width w = 230 nm, length l = 354 nm and periodicity p = 835 nm. The simulated efficiency of the lens is 60%, while the master lenses obtained by using electron beam lithography are found to have an efficiency of 45%. The lenses subsequently fabricated via nanoimprint are characterized by an efficiency of 6%; the low efficiency is mainly attributed to the rounding of the rectangular nanostructures during the pattern transfer processes from the resist to silicon due to the presence of a thicker residual layer.

In this paper, three deposition techniques are combined to create a window material with high average transmission at oblique angles of incidence. Spectrophotometry and ellipsometry measurements, respectively, yield the optical constants n and k. In contrast with other analyses on the subject, a high average transmission, higher than 91% in the 450-900 nm spectral range, is obtained at incident angles of 20-25 degrees. The refractive index and extinction coefficient are determined by the Swanepoel method. The iterative optimization performed using the OpenFilters software leads to an antireflection (AR) multilayer with low reflection and high transmission. The surface quality of the films was characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM), which revealed compact, continuous, and smooth films.

In this work, synthesis and optical properties of a new composite based on poly(o-phenylenediamine) (POPD) fiber like structures, poly(vinylidene fluoride) (PVDF) spheres and double-walled carbon nanotubes (DWNTs) are reported. As increasing the PVDF weight in the mixture of the chemical polymerization reaction of o-phenylenediamine, the presence of the PVDF spheres onto the POPD fibers surface is highlighted by scanning electron microscopy (SEM). The down-shift of the Raman line from 1421 cm(-1) to 1415 cm(-1) proves the covalent functionalization of DWNTs with the POPD-PVDF blends. The changes in the absorbance of the IR bands peaked around 840, 881, 1240 and 1402 cm(-1) indicate hindrance steric effects induced of DWNTs to the POPD fiber like structures and the PVDF spheres, as a consequence of the functionalization process of carbon nanotubes with macromolecular compounds. The presence of the PVDF spheres onto the POPD fiber like structures surface induces a POPD photoluminescence (PL) quenching process. An additional PL quenching process of the POPD-PVDF blends is reported to be induced in the presence of DWNTs. The studies of anisotropic PL highlight a change of the angle of the binding of the PVDF spheres onto the POPD fiber like structures surface from 50.2 degrees to 38 degrees when the carbon nanotubes concentration increases in the POPD-PVDF/DWNTs composites mass up to 2 wt.%.

This paper prepared composites under the free membranes form that are based on thermoplastic polymers of the type of polyurethane (TPU) and polyolefin (TPO), which are blended in the weight ratio of 2:1, and ceramic nanoparticles (CNs) such as BaSrTiO3 and SrTiO3. The structural, optical, and conductive properties of these new composite materials are reported. The X-ray diffraction studies highlight a cubic crystalline structure of these CNs. The main variations in the vibrational properties of the TPU:TPO blend induced by CNs consist of the following: (i) the increase in the intensity of the Raman line of 1616 cm(-1); (ii) the down-shift of the IR band from 800 to 791 cm(-1); (iii) the change of the ratio between the absorbance of IR bands localized in the spectral range 950-1200 cm(-1); and (iv) the decrease in the absorbance of the IR band from 1221 cm(-1). All these variations were correlated with a preferential adsorption of thermoplastic polymers on the CNs surface. A photoluminescence (PL) quenching process of thermoplastic polymers is demonstrated to occur in the presence of CNs. The anisotropic PL measurements have highlighted a change in the angle of the binding of the TPU:TPO blend, which varies from 23.7 degrees to approximate to 49.3 degrees and approximate to 53.4 degrees, when the concentration of BaSrTiO3 and SrTiO3 CNs, respectively, is changed from 0 to 25 wt. %. Using dielectric spectroscopy, two mechanisms are invoked to take place in the case of the composites based on TPU:TPO blends and CNs, i.e., one regarding the type of the electrical conduction and another specifying the dielectric-dipolar relaxation processes.

In this work, the photodegradation process of atorvastatin calcium (ATC) is reported as depending on: (1) the presence and the absence of excipients in the solid state; (2) the chemical interaction of ATC with phosphate buffer (PB) having pH equal to 7 and 8; and (3) hydrolysis reaction of ATC in the presence of aqueous solution of NaOH. The novelty of this work consists in the monitoring of the ATC photodegradation by photoluminescence (PL). The exposure of ATC in solid state to UV light induces the photo-oxygenation reactions in the presence of water vapors and oxygen from air. According to the X-ray photoelectron spectroscopic studies, we demonstrate that the photo-oxygenation reaction leads to photodegradation compounds having a high share of C=O bonds compared to ATC before exposure to UV light. Both in the presence of PB and NaOH, the photodegradation process of ATC is highlighted by a significant decrease in the intensity of the PL and photoluminescence excitation (PLE) spectra. According to PLE spectra, the exposure of ATC in the presence of NaOH to UV light leads to the appearance of a new band in the spectral range 340-370 nm, this belonging to the photodegradation products. Arguments concerning the chemical compounds, that resulted in this last case, are shown by Raman scattering and FTIR spectroscopy.

Ge2Sb2Te5 (GST-225) is a chalcogenide material with applications in nonvolatile memories. However, chalcogenide material properties are dependent on the deposition technique. GST-225 thin films were prepared using three deposition methods: magnetron sputtering (MS), pulsed laser deposition (PLD) and a deposition technique that combines MS and PLD, namely MSPLD. In the MSPLD technique, the same bulk target is used for sputtering but also for PLD at the same time. The structural and optical properties of the as-deposited and annealed thin films were characterized by Rutherford backscattering spectrometry, X-ray reflectometry, X-ray diffraction, Raman spectroscopy and spectroscopic ellipsometry. MS has the advantage of easily leading to fully amorphous films and to a single crystalline phase after annealing. MS also produces the highest optical contrast between the as-deposited and annealed films. PLD leads to the best stoichiometric transfer, whereas the annealed MSPLD films have the highest mass density. All the as-deposited films obtained with the three methods have a similar optical bandgap of approximately 0.7 eV, which decreases after annealing, mostly in the case of the MS sample. This study reveals that the properties of GST-225 are significantly influenced by the deposition technique, and the proper method should be selected when targeting a specific application. In particular, for electrical and optical phase change memories, MS is the best suited deposition method.

The lack of order in amorphous chalcogenides offers them novel properties but also adds increased challenges in the discovery and design of advanced functional materials. The amorphous compositions in the Si-Ge-Te system are of interest for many applications such as optical data storage, optical sensors and Ovonic threshold switches. But an extended exploration of this system is still missing. In this study, magnetron co-sputtering is used for the combinatorial synthesis of thin film libraries, outside the glass formation domain. Compositional, structural and optical properties are investigated and discussed in the framework of topological constraint theory. The materials in the library are classified as stressed-rigid amorphous networks. The bandgap is heavily influenced by the Te content while the near-IR refractive index dependence on Ge concentration shows a minimum, which could be exploited in applications. A transition from a disordered to a more ordered amorphous network at 60 at% Te, is observed. The thermal stability study shows that the formed crystalline phases are dictated by the concentration of Ge and Te. New amorphous compositions in the Si-Ge-Te system were found and their properties explored, thus enabling an informed and rapid material selection and design for applications.

Tuning the intrinsic structural and stoichiometric properties by different means is used for increasing the green energy production efficiency of complex oxide materials. Here, we report on the formation of self-assembled nanodomains and their effects on the photoelectrochemical (PEC) properties of LaFeO3 (LFO) epitaxial thin films as a function of layer's thickness. The variation with the film's thickness of the structural parameters such as in-plane and out-of-plane crystalline coherence length and the coexistence of different epitaxial orientation-SrTiO3// LFO, SrTiO3// LFO and [110] LFO//[10] STO, as well as the appearance of self-assembled nanodomains for film's thicknesses higher than 14 nm, is presented. LFO thin films exhibit different epitaxial orientations depending on their thickness, and the appearance of self-assembled nanopyramids-like domains after a thickness threshold value has proven to have a detrimental effect on the PEC functional properties. Using Nb:SrTiO3 as conductive substrate and 0.5 M NaOH aqueous solution for PEC measurements, the dependence of the photocurrent density and the onset potential vs. RHE on the structural and stoichiometric features exhibited by the LFO photoelectrodes are unveiled by the X-ray diffraction, high-resolution transmission electron microscopy, ellipsometry, and Rutherford backscattering spectroscopy results. The potentiodynamic PEC analysis has revealed the highest photocurrent density J(photocurrent) values (up to 1.2 mA/cm(2)) with excellent stability over time, for the thinnest LFO/Nb:SrTiO3 sample, both cathodic and anodic behavior being noticed. Noticeably, the LFO thin film shows unbiased hydrogen evolution from water, as determined by gas chromatography in aqueous 0.5 M NaOH solution under constant illumination.

Amorphous metal chalcogenides have good switching properties for resistive memories, but have low thermal stability. In this work, the response to rapid thermal stress, as high as 550 degrees C, of amorphous Cu-GeSe, Ag-GeSe, Cu-GeTe, Ag-GeTe thin films, is investigated. Metal-GeTe films, which are amorphous up to 280 degrees C, are the most stable. Metal-GeSe films start to crystallize at 190 degrees C and a Cu1.59Se phase, with 20.5% Cu vacancies and a structure similar to the c-Cu2-xSe superionic conductor, is formed. This might boost the performance of memory devices. Silver atoms migration is facilitated in Ag-GeSe by poor crystallization (below 5%, at all temperatures). Difussion of Ag is enhanced in Ag-GeTe, due to the crystallization of the cubic (Ag2Te)(4)-GeTe2 (Ag8GeTe6) phase, which has Ag+ vacancies. In Cu-GeTe, the formation of stoichiometric polycrystalline Cu0.67Ge0.33 Te might hinder diffusion. An unusual anisotropic behaviour (increase in thickness, simultaneously with contraction of surface) is observed at 100 degrees C in Cu-GeSe and Cu-GeTe thin films, which suggests the orientation of the amorphous clusters package along a preferential direction.