National Institute Of Materials Physics - Romania

Cation-substituted hydroxyapatite (HA), standalone or as a composite (blended with polymers or metals), is currently regarded as a noteworthy candidate material for bone repair/regeneration either in the form of powders, porous scaffolds or coatings for endo-osseous dental and orthopaedic implants. As a response to the numerous contradictions reported in literature, this work presents, in one study, the physico-chemical properties and the cytocompatibility response of single cation-doped (Ce, Mg, Sr or Zn) HA nanopowders in a wide concentration range (0.5-5 at.%). The modification of composition, morphology, and structure was multiparametrically monitored via energy dispersive X-ray, X-ray photoelectron, Fourier-transform infrared and micro-Raman spectroscopy methods, as well as by transmission electron microscopy and X-ray diffraction. From a compositional point of view, Ce and Sr were well-incorporated in HA, while slight and pronounced deviations were observed for Mg and Zn, respectively. The change of the lattice parameters, crystallite size, and substituting cation occupation factors either in the Ca(I) or Ca(II) sites were further determined. Sr produced the most important HA structural changes. The in vitro biological performance was evaluated by the (i) determination of leached therapeutic cations (by inductively coupled plasma mass spectrometry) and (ii) assessment of cell behaviour by both conventional assays (e.g., proliferation-3-(4,5-dimethyl thiazol-2-yl) 5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium assay; cytotoxicity-lactate dehydrogenase release assay) and, for the first time, real-time cell analysis (RTCA). Three cell lines were employed: fibroblast, osteoblast, and endothelial. When monophasic, the substituted HA supported the cells' viability and proliferation without signs of toxicity. The RTCA results indicate the excellent adherence of cells. The study strived to offer a perspective on the behaviour of Ce-, Mg-, Sr-, or Zn-substituted HAs and to deliver a well-encompassing viewpoint on their effects. This can be highly important for the future development of such bioceramics, paving the road toward the identification of candidates with highly promising therapeutic effects.

Highly dispersed supported NbOx species were prepared via a deposition precipitation-carbonization (DPC)-like method. As precursors for niobium species and carrier ammonium niobate(V) oxalate hydrate and humins were used. Characterization of the resulted catalysts indicated bi-functional acid-base niobium species anchored onto a highly hydrophobic graphite-like carbon structure. These catalysts were investigated in the one-pot conversion of glucose to 5-hydroxymethylfurfural (HMF) in a biphasic system consisting of a mixture of a 20 wt% NaCl aqueous solution phase and an organic extracting phase (methyl-isobutyl-ketone (MIBK), 2-tert-butylphenol (TBP) or 2sec-butylphenol (SBP)). The optimization conditions afforded the highest yield to HMF (96 %) for the GHNb1.2 catalyst (with 2.5 wt%Nb), the base/acid sites ratio of 1.76, in biphasic TBP/water system, at 180 ?C after 8 h.

Structural and electrical properties of epitaxial Pb(Zr0.2Ti0.8)O-3 films grown by pulsed laser deposition from targets with different purities are investigated in this study. One target was produced in-house by using high purity precursor oxides (at least 99.99%), and the other target was a commercial product (99.9% purity). It was found that the out-of-plane lattice constant is about 0.15% larger and the a domains amount is lower for the film grown from the commercial target. The polarization value is slightly lower, the dielectric constant is larger, and the height of the potential barrier at the electrode interfaces is larger for the film deposited from the pure target. The differences are attributed to the accidental impurities, with a larger amount in the commercial target as revealed by composition analysis using inductive coupling plasma-mass spectrometry. The heterovalent impurities can act as donors or acceptors, modifying the electronic characteristics. Thus, mastering impurities is a prerequisite for obtaining reliable and reproducible properties and advancing towards all ferroelectric devices.

In this study, nano-BaTiO3 (BTO) powders were obtained via the solvothermal method at different reaction times and were investigated using transmission electron microscopy (TEM), X-ray diffraction (XRD) and Raman spectroscopy. The results were compared with those obtained for a larger crystallite size BTO powder (BTO-m). The sizes of the cuboid crystallites (as determined by XRD and TEM) ranged from about 18 to 24 nm, depending on the reaction time. The evolution with temperature of the structure parameters of nano-BTO was monitored by means of X-ray diffraction and Raman spectroscopy and no signs of phase transition were found up to 170 degrees C. Careful monitoring of the dependence of the XRD peak widths on the hkl indices showed that the effect of the cubic crystallite shape upon the XRD peak widths was buried by the effect of hidden tetragonal line splits and by anisotropic microstrain. The good correlation of the line widths with the tetragonal split amplitudes, observed especially for BTO-m above the transition temperature, indicates tetragonal deformations, as also revealed by Raman spectroscopy. The large anisotropic microstrain shown by the nano-powders, which had a maximum value in the directions, was considered evidence of the phenomenon of surface relaxation of cubic crystallites edged by {100} faces. The observed behavior of the nano-BTO structures with increasing temperature may suggest a correlation between the surface relaxation and tetragonal deformation in the nano-cubes. The experimental results for both nano-BTO and mezoscale-BTO are in agreement with the core-shell model.

Properties of epitaxial PbZr0.2Ti0.8O3 (PZT) films deposited on Si substrates were investigated for integration in the present CMOS technology. Polarization is downward oriented, in association with the presence of an internal electric field, and has a lower value compared to the PZT films deposited on single crystal perovskite SrTiO3 (STO) substrates (40 mu C/cm(2) versus 80 mu C/cm(2)), while the dielectric constant is larger (180 versus 120). Large value for the pyroelectric coefficient was also found, 1.22 x 10(-3)C/m(2)K, as for PZT grown on single crystal STO. The macroscopic ferroelectric and pyroelectric properties appear to be affected by the structural quality and stoichiometry of the PZT film. The changes in the electric properties are an effect of the strain gradients induced by the large difference between the thermal expansion coefficients of PZT and Si substrate, leading in turn to Pb oxidation and antisite defect formation compared to PZT films deposited on STO substrates.

Lanthanum orthophosphate (LaPO4) and La0.95-xCe0.05MnxPO4 (x = 0.00, 0.03, 0.10) phosphors were synthesized by a simple and cost-efficient co-precipitation method and the formation of LaPO4 nanorods with a monoclinic P21/n crystal structure was observed. X-ray diffraction pattern analysis indicated a slight distortion of the LaPO4 crystalline structure and an increase of the lattice strain as a consequence of the Mn2+ and Ce3+ dopants incorporation in the host matrix. Scanning electron microscopy revealed that the microstructure of all powders consists of agglomerations of nanorods, which are around 17 +/- 3 nm in diameter and length ranging from 100 nm to 300 nm. Electron paramagnetic resonance measurements have indicated the presence of Mn2+ in isolated species, but also as agglomerates. Ce3+ and Mn2+ doping of LaPO4 resulted also in a decrease of the band gap up to 4.70 eV compared to the un-doped sample. Because of an energy transfer effect from Ce3+ to Mn2+ ions, green emission of Mn2+ ions at around 550 nm was observed upon 275 nm excitation.

In this paper, potassium based triple cation mixed-halide perovskite films were explored in order to enhance the stability and photovoltaic performance of perovskite based solar cells. It was found that adding potassium (K+) to a double cation mixed halide perovskite (FA(0.80)MA(0.20)PbI(2.8)Cl(0.2)), structural, morphological and optoelectronic properties of perovskites are improved. The perovskite films were prepared by one-step spin coating method with and without K+ and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), UV-Vis spectroscopy, X-ray photoelectron spectroscopy (XPS), and photoluminescence spectroscopy (PL). The results indicate that potassium incorporation reduces significantly the yellow non-perovskite delta-phase formation and improves the perovskite film quality, thus contributing to the reduction of hysteresis, improves the stability and increases the PCE up to 12.51%. Furthermore, the doped devices exhibit reduced hysteresis and provide remarkable shelf stability by retaining more than 70% of the initial efficiency with low humidity over 850 h. (C) 2020 Elsevier B.V. All rights reserved.

The paper presents the possibility of detecting low H2S concentrations using CuWO4. The applicative challenge was to obtain sensitivity, selectivity, short response time, and full recovery at a low operating temperature under in-field atmosphere, which means variable relative humidity (%RH). Three different chemical synthesis routes were used for obtaining the samples labeled as: CuW1, CuW2, and CuW3. The materials have been fully characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). While CuWO4 is the common main phase with triclinic symmetry, different native layers of CuO and Cu(OH)(2) have been identified on top of the surfaces. The differences induced into their structural, morphological, and surface chemistry revealed different degrees of surface hydroxylation. Knowing the poisonous effect of H2S, the sensing properties evaluation allowed the CuW2 selection based on its specific surface recovery upon gas exposure. Simultaneous electrical resistance and work function measurements confirmed the weak influence of moisture over the sensing properties of CuW2, due to the pronounced Cu(OH)(2) native surface layer, as shown by XPS investigations. Moreover, the experimental results obtained at 150 degrees C highlight the linear sensor signal for CuW2 in the range of 1 to 10 ppm H2S concentrations and a pronounced selectivity towards CO, CH4, NH3, SO2, and NO2. Therefore, the applicative potential deserves to be noted. The study has been completed by a theoretical approach aiming to link the experimental findings with the CuW2 intrinsic properties.

Pd deposited on CeOx-MnOx/La-Al2O3 has been prepared as a sensitive material for methane (CH4) detection. The effect of different amounts (1.25%, 2.5% and 5%) of Pd loading has been investigated. The as prepared materials were deposited on Pt microcoils using a drop-coating method, as a way of developing pellistors operated using a Wheatstone bridge configuration. By spanning the operating temperature range between 300 degrees C and 550 degrees C, we established the linearity region as well as the maximum sensitivity towards 4900 ppm of CH4. By making use of the sigmoid dependence of the output voltage signal from the Wheatstone bridge, the gas surface reaction and diffusion phenomena have been decoupled. The pellistor with 5% Pd deposited on CeOx-MnOx/La-Al2O3 exhibited the highest selective-sensitivity in the benefit of CH4 detection against threshold limits of carbon monoxide (CO), sulfur dioxide (SO2) and hydrogen sulfide (H2S). Accordingly, adjusting the percent of Pd makes the preparation strategies of pellistors good candidates towards CH4 detection.

The development of robust, safe, cost-effective and efficient photocatalytic systems for water splitting should take into account the presence of a proper and powerful photon absorber and an efficient, low-cost and earth-abundant electrocatalyst to perform the reaction at high conversions. In this study, Ni-Zn/TiO(2)ternary composites with high photocatalytic activity for water splitting under UV irradiation were successfully prepared via a simple and low-cost deposition-precipitation route. Thus, different Ni : Zn molar ratios (1 : 0, 1 : 1, 3 : 1, 6 : 1, 9 : 1, and 0 : 1) were deposited on TiO(2)in order to reach a total metal loading of 50 wt. %. The obtained composites were characterized using several techniques, such as: X-ray diffraction, UV-Vis spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy. The most active synthesized composite, namely Ni-Zn/TiO2(9 : 1), exhibits H(2)generation rate above 17 mmols g(-1) h(-1), which is nearly one thousand times higher than that obtained with TiO(2)Evonik P25. Our study demonstrates that TiO(2)becomes a degenerated semiconductor in the presence of Ni and ZnO, with remarkable photocatalytic properties. Thus, the obtained results can open new opportunities in the preparation of very active materials for hydrogen production based on the optimization of three-component structures.