National Institute Of Materials Physics - Romania

In this work, new optical properties of composites based on polystyrene (PS) microspheres and graphene oxide (GO) are reported. The radical polymerization of styrene in the presence of benzoyl peroxide, pentane and GO induces the appearance of new ester groups in the PS macromolecular chains remarked through an increase in the absorbance of the infrared (IR) band at 1743 cm(-1). The decrease in the GO concentration in the PS/GO composites mass from 5 wt.% to 0.5 wt.% induces a diminution in the intensities of the D and G Raman bands of GO simultaneous with a down-shift of the D band from 1351 to 1322 cm(-1). These variations correlated with the covalent functionalization of the GO layers with PS. For the first time, the photoluminescent (PL) properties of PS/GO composites are reported. The PS microspheres are characterized by a PL band at 397 nm. Through increasing the GO sheets' concentration in the PS/GO composite mass from 0.5 wt.% to 5 wt.%, a PS PL quenching process is reported. In addition, in the presence of ultraviolet A (UVA) light, a photo-degradation process of the PS/GO composite having the GO concentration equal to 5 wt.% is demonstrated by the PL studies.

This work involves the synthesis and characterization of Cu2ZnSnS4 (CZTS) layers. The films were prepared on Mo/glass substrates by single-step electrodeposition method followed by sulfurization at 500 degrees C under argon flow. The effect of boric acid concentration on the crystallographic structure, compositional and morphological properties of CZTS films was investigated, with the objective to understand the growth behavior and to enhance the film properties. Cyclic Voltammetry was used in order to estimate the adequate deposition potential for the CZT alloy. The x-ray diffraction analysis showed the formation of the kesterite phase in all the samples. The Raman and x-ray photoelectron spectroscopy studies confirmed the existence of the CZTS phase. The scanning electron microscopy was employed to inspect the films structure. The results indicated that increasing the concentration of boric acid affects the physico-chemical properties of the films.

This paper presents some studies on the organic heterostructures realized by Matrix Assisted Pulsed Laser Evaporation in both bi-layer and mixed layer configurations on glass substrates covered by flat or nano-patterned ITO. The donor, a star-shaped arylenevinylene compound, 4,4',4 ''-tris[(4'-diphenylamino) styryl] triphenylamine, and acceptor, a non-fullerene compound, N,N'-bis-(1-dodecyl)perylene-3,4,9,10 tetracarboxylic diimide, were blended in three weight ratios: 1:2, 1:3 and 1:4. A grating of cylindrical pillars with a periodicity of 1.1 mu m has been developed by UV-Nanoimprint Lithography in a polymer layer. The shape of the nanostructures changed to cone trunk by the Pulsed Laser Deposition of ITO on this nanostructured surface. The effect of the nanostructures and composition on the optical and electrical properties of the heterostructures was analyzed. The nano-patterning affected both the UV-Vis transmission and photoluminescence through the multiple reflections inside the cavities and at interfaces and the particularities of the molecular arrangement. The patterning was preserved independently of composition, but the roughness increased with increasing acceptor amount. The I-V characteristics drawn at room temperature in dark revealed an ohmic contact behavior for all heterostructures. The nano-patterning had a similar effect on the current in the heterostructures with mixed layer (1:2) and stacked bi-layer.

The effect of UV light on the cationic photopolymerization of the SU8 negative photoresist is shown by photoluminescence (PL) studies. Our results demonstrate that the cationic photopolymerization reaction of the SU8 photoresist takes place predominantly under the influence of the UVA light. Using UVA light, the influence of carbon nanotubes [of the types single-walled carbon nanotubes (SWNTs), double-walled carbon nanotubes (DWNTs), multiwalled carbon nanotubes (MWNTs), and SWNTs functionalized with carboxyl groups (SWNTs-COOH)] on the cationic photopolymerization process of the SU8 photoresist is shown by PL studies. The cationic photopolymerization of the SU8 photoresist is monitored by the variations of the two emission bands with maxima at similar to 400-429 nm and 523-556 nm. The increase in the relative intensity of the PL band at similar to 523-556 nm is dependent on (i) the carbon nanotube concentration in the SU8 photoresist matrix; (ii) the type of carbon nanotubes, i.e., SWNTs, DWNTs, and MWNTs; and (iii) the nonfunctionalized and functionalized state of SWNTs. The results reported in this work demonstrate that PL can be used as a complementary method to Raman scattering and IR spectroscopy in the investigation of the cationic photopolymerization reaction of the SU8 negative photoresist. A decrease in the wrapping angle of carbon nanotubes with the SU8 photoresist is highlighted by anisotropic PL studies.

In this work, the effect of aliovalent substitution of Pb2+ by Eu3+ on structural, morphological and optical properties of CH3NH3PbI3 (MAPbI(3)) was studied, aiming to improve the properties of perovskite films used in solar cells application. The surface morphology, the microstructure and the optical properties of the obtained films containing different Europium (Eu) concentrations were characterized by atomic force microscopy, x-ray photoelectron spectroscopy, x-ray diffraction, UV-vis spectroscopy and photoluminescence spectroscopy.

A complete characterization from optical, morphological, electrical, photo-electrical and thermo-electrical point of view was done for PEDOT:PSS thin films and DMSO and EG sensitized PEDOT:PSS films. The studies on the electrical conductivity and electrical photoconductivity allowed the calculation of different relaxation times. The relaxation time of the electrical conductivity is of order of femtosecond and is multiplied by a factor 10 when PEDOT: PSS thin films were deposited on surfaces sensitized with DMSO and EG. Besides, the photoconduction excitation and relaxation times are of order of seconds. An increase in the relaxation photoconduction time by 2 was observed for films deposited on surfaces sensitized with DMSO and by 1.2 for films deposited on surfaces sensitized with EG. The time response of electrical conductivity after exposure to light adds supplementary knowledge for the understanding of the inertial processes, or hysteresis behavior of organic or perovskite solar cells involving PEDOT:PSS films. The electrical conductivity increases with the temperature and the use of DMSO and EG as surfactants lead to higher values of electrical conductivity and Seebeck coefficient. A better stability of the electrical conductivity with the temperature increase, was noticed for films deposited on surfaces sensitized with DMSO.

Tellurium metallic colloids were evidence in the phosphate tellurite glasses obtained by the melt quenching method over 1000 degrees C. The concentration and subsequent color of these glasses strongly depend on the preparation conditions due to the significant differences among the melting point of the component oxides. The presence of Te metallic colloids was evidenced by the magneto-optical measurements at different temperatures, by the shift of the emissions spectra with the excitation wavelength and the thermoluminescence spectra as a result of recombination between the hole centers, created during x-ray irradiation, with the quasi coupled electrons from the surface of the metallic colloids. The peak position in the absorption spectra of these metallic colloids was modeled based on generalized Mie light scattering theory on these metallic structures, taking into account the size and shape of colloids but also the dielectric constant of the phosphate tellurite glasses in which these colloids are embedded.

Matrix-assisted pulsed laser evaporation (MAPLE) was used to deposit hybrid nanocomposite thin films based on cobalt phthalocyanine (CoPc), C60 fullerene and ZnO nanoparticles. The inorganic nanoparticles, with a size of about 20 nm, having the structural and optical properties characteristic of ZnO, were chemically synthesized by a simple precipitation method. Furthermore, ZnO nanoparticles were dispersed in a dimethyl sulfoxide solution in which CoPc and C60 had been dissolved, ready for the freezing MAPLE target. The effect of the concentration of ZnO nanoparticles on the structural, morphological, optical and electrical properties of the CoPc:C60:ZnO hybrid nanocomposite layers deposited by MAPLE was evaluated. The infrared spectra of the hybrid nanocomposite films confirm that the CoPc and C60 preserve their chemical structure during the laser deposition process. The CoPc optical signature is recognized in the ultraviolet-visible (UV-Vis) spectra of the obtained layers, these being dominated by the absorption bands associated to this organic compound while the ZnO optical fingerprint is identified in the photoluminescence spectra of the prepared layers, these disclosing the emission bands linked to this inorganic semiconductor. The hybrid nanocomposite layers exhibit globular morphology, which is typical for the thin films deposited by MAPLE. Current-voltage (J-V) characteristics of the structures developed on CoPc:C60:ZnO layers reveal that the addition of an appropriate amount of ZnO nanoparticles in the CoPc:C60 mixture leads to a more efficient charge transfer between the organic and inorganic components. Due to their photovoltaic effect, structures featuring such hybrid nanocomposite thin films deposited by MAPLE can have potential applications in the field of photovoltaic devices.

Our study focused on the long-term degradation under simulated conditions of coatings based on different compositions of polycaprolactone-polyethylene glycol blends (PCL-blend-PEG), fabricated for titanium implants by a dip-coating technique. The degradation behavior of polymeric coatings was evaluated by polymer mass loss measurements of the PCL-blend-PEG during immersion in SBF up to 16 weeks and correlated with those yielded from electrochemical experiments. The results are thoroughly supported by extensive compositional and surface analyses (FTIR, GIXRD, SEM, and wettability investigations). We found that the degradation behavior of PCL-blend-PEG coatings is governed by the properties of the main polymer constituents: the PEG solubilizes fast, immediately after the immersion, while the PCL degrades slowly over the whole period of time. Furthermore, the results evidence that the alteration of blend coatings is strongly enhanced by the increase in PEG content. The biological assessment unveiled the beneficial influence of PCL-blend-PEG coatings for the adhesion and spreading of both human-derived mesenchymal stem cells and endothelial cells.

Single-phase Ba1-xSrxTiO3 (BST) perovskite ceramics with 0.3 <= x <= 0.4 were prepared from powders synthesized via sol-gel route. The compositions have the ferroelectric-paraelectric phase transition close to room temperature. At 20 degrees C the BST ceramics are ferroelectric for 0.3 <= x <= 0.35 and paraelectric for x = 0.375 and x = 0.40. The study follows the relation between the structural changes produced when increasing the Sr content and the dielectric properties at low intensity electric fields. It is found that the grain size and tetragonality decreases as the Sr content increases. Analyses of complex permittivity and impedance spectroscopy reveal the temperature and frequency dependencies of the dielectric properties. The phase transitions seem to be of first order for all compositions, with a thermal hysteresis that decreases with increasing the Sr content, fact attributed to the corresponding increase of the grain boundaries weight allowing a more efficient stress relaxation in the structure during the change of the symmetry from cubic to tetragonal. The diffusiveness degree during the phase transition is increasing with Sr content, suggesting some relaxor-type contribution attributed to smaller grain size. The ac conductivity follows the universal Jonscher law, with an ac component having the power parameter s independent of Sr content, and a dc component that it is thermally activated with an activation energy of about 0.7-0.77 eV attributed to oxygen vacancies acting as donor-like defects. The fit of impedance spectra at different temperatures and frequencies is obtained by using an equivalent circuit accounting the grains, grain boundaries, electrode interfaces and the local contributions produced by reorientation of defect dipoles or defect clusters. All the component circuits have significant variations around phase transitions. These are discussed in relation to structural changes occurring during transition and considering the changes in the distribution of various charges when polarization vanishes.