National Institute Of Materials Physics - Romania

In this paper, potassium based triple cation mixed-halide perovskite films were explored in order to enhance the stability and photovoltaic performance of perovskite based solar cells. It was found that adding potassium (K+) to a double cation mixed halide perovskite (FA(0.80)MA(0.20)PbI(2.8)Cl(0.2)), structural, morphological and optoelectronic properties of perovskites are improved. The perovskite films were prepared by one-step spin coating method with and without K+ and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), UV-Vis spectroscopy, X-ray photoelectron spectroscopy (XPS), and photoluminescence spectroscopy (PL). The results indicate that potassium incorporation reduces significantly the yellow non-perovskite delta-phase formation and improves the perovskite film quality, thus contributing to the reduction of hysteresis, improves the stability and increases the PCE up to 12.51%. Furthermore, the doped devices exhibit reduced hysteresis and provide remarkable shelf stability by retaining more than 70% of the initial efficiency with low humidity over 850 h. (C) 2020 Elsevier B.V. All rights reserved.

The paper presents the possibility of detecting low H2S concentrations using CuWO4. The applicative challenge was to obtain sensitivity, selectivity, short response time, and full recovery at a low operating temperature under in-field atmosphere, which means variable relative humidity (%RH). Three different chemical synthesis routes were used for obtaining the samples labeled as: CuW1, CuW2, and CuW3. The materials have been fully characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). While CuWO4 is the common main phase with triclinic symmetry, different native layers of CuO and Cu(OH)(2) have been identified on top of the surfaces. The differences induced into their structural, morphological, and surface chemistry revealed different degrees of surface hydroxylation. Knowing the poisonous effect of H2S, the sensing properties evaluation allowed the CuW2 selection based on its specific surface recovery upon gas exposure. Simultaneous electrical resistance and work function measurements confirmed the weak influence of moisture over the sensing properties of CuW2, due to the pronounced Cu(OH)(2) native surface layer, as shown by XPS investigations. Moreover, the experimental results obtained at 150 degrees C highlight the linear sensor signal for CuW2 in the range of 1 to 10 ppm H2S concentrations and a pronounced selectivity towards CO, CH4, NH3, SO2, and NO2. Therefore, the applicative potential deserves to be noted. The study has been completed by a theoretical approach aiming to link the experimental findings with the CuW2 intrinsic properties.

Pd deposited on CeOx-MnOx/La-Al2O3 has been prepared as a sensitive material for methane (CH4) detection. The effect of different amounts (1.25%, 2.5% and 5%) of Pd loading has been investigated. The as prepared materials were deposited on Pt microcoils using a drop-coating method, as a way of developing pellistors operated using a Wheatstone bridge configuration. By spanning the operating temperature range between 300 degrees C and 550 degrees C, we established the linearity region as well as the maximum sensitivity towards 4900 ppm of CH4. By making use of the sigmoid dependence of the output voltage signal from the Wheatstone bridge, the gas surface reaction and diffusion phenomena have been decoupled. The pellistor with 5% Pd deposited on CeOx-MnOx/La-Al2O3 exhibited the highest selective-sensitivity in the benefit of CH4 detection against threshold limits of carbon monoxide (CO), sulfur dioxide (SO2) and hydrogen sulfide (H2S). Accordingly, adjusting the percent of Pd makes the preparation strategies of pellistors good candidates towards CH4 detection.

The development of robust, safe, cost-effective and efficient photocatalytic systems for water splitting should take into account the presence of a proper and powerful photon absorber and an efficient, low-cost and earth-abundant electrocatalyst to perform the reaction at high conversions. In this study, Ni-Zn/TiO(2)ternary composites with high photocatalytic activity for water splitting under UV irradiation were successfully prepared via a simple and low-cost deposition-precipitation route. Thus, different Ni : Zn molar ratios (1 : 0, 1 : 1, 3 : 1, 6 : 1, 9 : 1, and 0 : 1) were deposited on TiO(2)in order to reach a total metal loading of 50 wt. %. The obtained composites were characterized using several techniques, such as: X-ray diffraction, UV-Vis spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy. The most active synthesized composite, namely Ni-Zn/TiO2(9 : 1), exhibits H(2)generation rate above 17 mmols g(-1) h(-1), which is nearly one thousand times higher than that obtained with TiO(2)Evonik P25. Our study demonstrates that TiO(2)becomes a degenerated semiconductor in the presence of Ni and ZnO, with remarkable photocatalytic properties. Thus, the obtained results can open new opportunities in the preparation of very active materials for hydrogen production based on the optimization of three-component structures.

The development of robust, safe, cost-effective and efficient photocatalytic systems for water splitting should take into account the presence of a proper and powerful photon absorber and an efficient, low-cost and earth-abundant electrocatalyst to perform the reaction at high conversions. In this study, Ni-Zn/TiO(2)ternary composites with high photocatalytic activity for water splitting under UV irradiation were successfully prepared via a simple and low-cost deposition-precipitation route. Thus, different Ni : Zn molar ratios (1 : 0, 1 : 1, 3 : 1, 6 : 1, 9 : 1, and 0 : 1) were deposited on TiO(2)in order to reach a total metal loading of 50 wt. %. The obtained composites were characterized using several techniques, such as: X-ray diffraction, UV-Vis spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy. The most active synthesized composite, namely Ni-Zn/TiO2(9 : 1), exhibits H(2)generation rate above 17 mmols g(-1) h(-1), which is nearly one thousand times higher than that obtained with TiO(2)Evonik P25. Our study demonstrates that TiO(2)becomes a degenerated semiconductor in the presence of Ni and ZnO, with remarkable photocatalytic properties. Thus, the obtained results can open new opportunities in the preparation of very active materials for hydrogen production based on the optimization of three-component structures.

This study reports on the results obtained after doping the [CH3NH3](0.94)[C3N2H5](0.06)PbI2.6Cl0.4 mixt halide perovskite with europium or antimony (Eu3+/Sb3+) at the 'B site'. This way two new complex compounds were obtained, [CH3NH3](0.94)[C3N2H5](0.06)Pb1-yByI2.6Cl0.4 (B = Eu or Sb and y = 0-0.05) as perovskite precursor solutions and deposited as thin films. The properties of the perovskite films were investigated by various characterization techniques: x-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), UV-vis spectroscopy while the photovoltaic parameters were determined by measuring the IV curves of the corresponding solar cells. We find that doping the mixt halide perovskite with very small quantities of Sb improves the quality of the perovskite films and further improves the stability of perovskite solar cells.

The catalytic activity of a series of vanadium aluminophosphates catalysts prepared by sol-gel method followed by combustion of the obtained gel was evaluated in glycerol conversion towards methanol. The materials were characterized by several techniques such as X-ray diffraction (XRD), UV-vis, Fourier-transform infrared (FTIR), Raman and X-ray photoelectron (XPS) spectroscopies. The amount of vanadium incorporated in aluminophosphates framework played an important role in the catalytic activity, while in the products distribution the key role is played by the vanadium oxidation state on the surface. The sample that contains a large amount of V(4+)has the highest selectivity towards methanol. On the sample with the lowest vanadium loading the oxidation path to dihydroxyacetone is predominant. The catalyst with higher content of tetrahedral isolated vanadium species, such V5APO, is less active in breaking the C-C bonds in the glycerol molecule than the one containing polymeric species.

To improve the catalytic performance of an active layered double hydroxide (LDH)-derived CuCeMgAlO mixed oxide catalyst in the total oxidation of methane, it was promoted with different transition-metal cations. Thus, two series of multicationic mixed oxides were prepared by the thermal decomposition at 750 degrees C of their corresponding LDH precursors synthesized by coprecipitation at constant pH of 10 under ambient atmosphere. The first series of catalysts consisted of four M(3)CuCeMgAlO mixed oxides containing 3 at.% M (M = Mn, Fe, Co, Ni), 15 at.% Cu, 10 at.% Ce (at.% with respect to cations), and with Mg/Al atomic ratio fixed to 3. The second series consisted of four Co(x)CuCeMgAlO mixed oxides withx= 1, 3, 6, and 9 at.% Co, while keeping constant the Cu and Ce contents and the Mg/Al atomic ratio. All the mixed oxides were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) coupled with X-ray energy dispersion analysis (EDX), X-ray photoelectron spectroscopy (XPS), nitrogen adsorption-desorption at -196 degrees C, temperature-programmed reduction under hydrogen (H-2-TPR), and diffuse reflectance UV-VIS spectroscopy (DR UV-VIS), while thermogravimetric and differential thermal analyses (TG-DTG-DTA) together with XRD were used for the LDH precursors. The catalysts were evaluated in the total oxidation of methane, a test reaction for volatile organic compounds (VOC) abatement. Their catalytic performance was explained in correlation with their physicochemical properties and was compared with that of a reference Pd/Al(2)O(3)catalyst. Among the mixed oxides studied, Co(3)CuCeMgAlO was found to be the most active catalyst, with a temperature corresponding to 50% methane conversion (T-50) of 438 degrees C, which was only 19 degrees C higher than that of a reference Pd/Al(2)O(3)catalyst. On the other hand, this T(50)value was ca. 25 degrees C lower than that observed for the unpromoted CuCeMgAlO system, accounting for the improved performance of the Co-promoted catalyst, which also showed a good stability on stream.

Palladium is one of the most efficient metals for the hydrogenation of organic compounds. However, when molecules, such as nitroaromatics, with several reducible functionalities, are hydrogenated, Pd, like any other very active metal, such as nickel or platinum, often behaves unselectively. One strategy to render Pd more selective is to choose the proper support. Herein, we show that MAX phase powders of Ti3SiC2, Ti2AlC, or Ti3AlC2 can chemoselectively hydrogenate 4-nitrostyrene to 4-aminostyrene, with 100% selectivity, at around 3-4% conversion. To boost the latter, we loaded Ti3SiC2 with 0.0005 wt % Pd and increased the conversion to 100% while maintaining the 4-AS selectivity at >90%. By optimizing the Pd loading, we were also able to increase the turnover frequency 100-fold relative to previous literature results. The identification of this highly efficient and chemoselective system has broad implications for the design of cost-effective, earth-abundant, nontoxic, metal catalysts, with ultralow noble metal loadings.

Mesoporous CeO2:Mn3O4 materials (3:7 and 7:3 molar ratio) were prepared by co-precipitation and deposited as porous thick films over alumina (Al2O3) planar substrate provided with Pt meander. The aim was oriented towards detecting low levels methane (CH4) at moderate operating temperatures. Herein we demonstrated that the sensitivity of catalytic micro-converters (CMCs) towards a given peak of CH4 concentration corresponds to specific gas-surface interaction phenomena. More precisely, a transition from thermal conductivity to combustion rate is likely to occur when CMCs are operated under real atmospheric conditions (normal pressure, presence of relative humidity, and constant operating temperature). The response to CH4 was analyzed over different gas flows and different gas concentrations under the same operating regime. The materials were fully characterized by adsorption-desorption isotherms, H-2-Temperature Programmed Reduction (H-2-TPR), X-ray Diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Scanning Electron Microscopy (SEM), and Raman spectroscopies. Thus, the applicative aspect of using CeO2:Mn3O4 as moderate temperature CMC for CH4 detection is brought to the fore.