National Institute Of Materials Physics - Romania

The current study aims to present and discuss the results obtained by complementary archaeometric methods applied for the first time on white pigments inlaid on excised pottery of the Boian-Vidra tradition (Early Chalcolithic, c. 4900-4600 BCE). The samples came from three settlements located in Southern Romania (Sultana-Ghetarie, Vidra, and Vladiceasca). They were selected considering that the pottery was produced in approximately contemporary sites, located relatively close to each other in the same geographical region, namely the Romanian Plain. The experimental part included the analysis of local samples of carbonate concretions and prehistoric animal bone ash as reference materials. Archaeometric investigations consisted in applying "in-air" PIXE and EDX methods for the chemical composition, XRD and FTIR for mineralogical data, SEM for microstructure observation, and EPR for the characterisation of the paramagnetic centres. Calcite, bone ash, and silica rich sediments were identified as the primary decorating pigments. The mixtures of calcite and bone-ash observed in 13 samples were specific to the sites at Vidra and Vladiceasca. Silica-rich sediments from distant sources were the main whitening materials in two samples from Vladiceasca, while for the samples from Sultana-Ghetarie, calcite was the only whitening mineral. The results show with a high degree of confidence the use of both local (i.e., carbonate neo-formations and bone ash) and exotic (silica-rich sediments) raw materials to obtain the white pigment applied to Boian-Vidra pottery. Thus, the current data show the adaptability of the potters with respect to the surrounding resources and also provide new evidence for a vast trade network of raw materials and/or finished products in the Lower Danube area during the Early Chalcolithic. The deliberate mixing of two whitening materials from different sources could be a technological choice and may highlight complex symbolic behaviours.

In this work, the influence of the preparation route on the structural, morphological, and thermoelectric properties of the Mg2Si0.4Sn0.6 solid solutions is investigated. The synthesis based on melting the constituent elements in a closed graphite crucible followed by spark plasma sintering allows mixing elements with a large difference of their melting temperatures and a good control of sample stoichiometry. The optimized synthesis route is validated by the doped V and Sb samples, which yield good thermoelectric performance. The n-type doping leads to two orders of magnitude increase of the carrier concentration, and thus a subsequent increase of the electrical conductivity, which, in turn, augments greatly the power factor of the Mg1.98V0.02Si0.385Sn0.6Sb0.015 to 42.61 x10(-4) Wm(-1)K 2 at 650K. Although doping slightly enlarges the thermal conductivity, a peak value of the figure of merit ZT similar to 1.15 is obtained at 723K, which is 20 times higher than the ZT of un-doped material.

This paper reports the synthesis and characterization of Cu2ZnSnS4 (CZTS) absorber films, prepared by a two-step electrodeposition of a ZnS (zinc sulfide) binary and a CZT (copper, zinc and tin) ternary precursors on Mo/Ti/Si substrates. The as-electrodeposited ZnS/CZT and CZT/ZnS stacks were thermally treated in a tubular furnace in sulfur environment at 550 degrees C. The role of the ZnS buffer layer is to provide a zinc and sulfur reservoir, needed to complete the formation of kesterite phase. X-ray diffraction and Raman analyses revealed the formation of the CZTS phase. The surface morphology and chemical composition of the films were studied using a scanning electron microscope. The bandgap values inferred from diffuse reflectance data, are discussed with respect to the stoichiometry which is considerably affected by the order of the stacks. Room-temperature photoluminescence of the CZT/ZnS sample showed a board PL band of 1.51 eV. It was found that the film with a ZnS layer on top is preferred for the formation of a Zn-rich single CZTS phase.

Laser-Induced Thermionic Vacuum Arc (LTVA) provides a better way to produce uniform metallic thin films than the classical Thermionic Vacuum Arc (TVA) method. In Ti-doped chromium thin films produced using LTVA, the amorphous chromium is superimposed with small bcc chromium nanoparticles. These amorphous/crystalline structures with small crystallites induce lower roughness and electrical resistivity, reducing electron-phonon scattering and increasing charge transport across LTVA thin films. A significant shift in resistivity for the LTVA samples is observed due to electron scattering on the phonon-crystalline structures in the TVA samples which exhibit larger crystallites. Meanwhile, the wettability measurements reveal a higher contact angle, resulting in a lower surface free energy and consecutively lower dissociation energy for the LTVA-produced thin films than the TVA samples.

New aspects concerning the photodegradation (PD) of ampicillin are reported by photoluminescence (PL), Raman scattering and FTIR spectroscopy. The exposure of ampicillin in the absence (AM) and in the presence of the excipient (AMP) to UV light leads to an intensity diminution of the photoluminescence excitation (PLE) and photoluminescence (PL) spectra and the emergence of a new IR band at 3450 cm(-1). The photoluminescence studies demonstrate that the AM PD is amplified in the presence of excipients and an alkaline medium. In this last case, the PD process of AM involves the emergence of new compounds, whose presence is highlighted by: (i) the emergence of the isosbestic point at 300 nm in the UV-VIS spectra; (ii) a change in the ratio between the absorbance of IR bands situated in the spectral ranges 1200-1660 and 3250-3450 cm(-1); and (iii) a change in the ratio between the intensities of the Raman lines localized in the spectral ranges 1050-1800 and 2750-3100 cm(-1). A chemical mechanism of the PD processes of AM in an alkaline medium is proposed.

Phosphate and tellurite glasses can be used in optics, optoelectronics, magneto-optics, and nuclear and medical fields. Two series of phosphate-tellurite glasses, (50-x)ZnO-10Al(2)O(3)-40P(2)O(5)-xTeO(2) and (40-x)Li2O-10Al(2)O(3)-5TiO(2)-45P(2)O(5)-xTeO(2) (x = 5, 10), were synthesized by a non-conventional wet-route, and the mechanical properties as key performance measures for their application in optoelectronics were investigated. X-ray Diffraction (XRD) measurements revealed the vitreous nature of the investigated materials. Instrumented indentation tests allowed the calculation of hardness (H) and Young's modulus (E) using the Oliver and Pharr model. The influence of increasing the TeO2 content, as well as the substitution of ZnO by Li2O-TiO2, on the variation of hardness, Young's modulus, penetration depth (PD), and fracture toughness (FT) was evaluated in both series. As a general trend, there is a decrease in the hardness and Young's modulus with increasing penetration depth. The addition of Li2O and TiO2 instead of ZnO leads to improved hardness and elastic modulus values. Regarding the H/E ratio, it was found that the samples with lower TeO2 content should be significantly more crack-resistant compared to the higher TeO2 content samples. The H-3/E-2 ratio, being lower than 0.01, revealed a poor resistance of these glasses to plastic deformation. At the same time, a decrease of the fracture toughness with increasing TeO2 content was noticed for each glass series. Based on dilatometry measurements, the thermal expansion coefficient as well as the characteristic temperatures of the glasses were measured. Field Emission Scanning Electron Microscopy-Energy Dispersive X-ray analysis (FESEM-EDX) revealed a uniform distribution of the elements in the bulk samples. The mechanical properties of these vitreous materials are important in relation to their application as magneto-optical Faraday rotators in laser cavities.

Silver doped hydroxyapatite [AgHAp, Ca10-xAg(PO4)(6)(OH)(2)], due to its antimicrobial properties, is an advantageous material to be used for various coatings. The AgHAp thin films with x(Ag) = 0.05 and x(Ag) = 0.1 were achieved using the spin-coating method. The resulting samples were examined by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). XRD analysis revealed that the particles of both samples are ellipsoidal. Also, in agreement with the results obtained by XRD measurements, the results of the SEM studies have shown that the particles shape is ellipsoidal. Optical properties of silver doped hydroxyapatite thin films deposited on Si substrate were investigated through Fourier transform infrared spectroscopy (FTIR) and Raman spectroscopy. The results obtained by the two complementary techniques highlighted that the molecular structure of the studied samples is not influenced by the increase of the silver concentration in the samples. Our studies revealed that the surface morphology of the obtained samples consist of uniform and continuous layers. The biocompatibility of the obtained thin films was also evaluated with the aid of human osteosarcoma MG63 (ATCC CRL 1427) cell line. Moreover, the in vitro antifungal activity against Candida albicans fungal strain of the AgHAp thin films was studied and the obtained results revealed their antifungal effect. The results of the biological assays showed that the AgHAp thin films are a very promising material for biomedical applications.

In this work, the thermally stimulated current (TSC) technique has been used to investigate the properties of the radiation-induced interstitial boron and interstitial oxygen defect complex by 23-GeV (E-kin) protons, including activation energy, defect concentration, as well as the annealing behavior. At first isothermal annealing (at 80 degrees C for 0-180 min) followed by isochronal annealing (for 15 min between 100 degrees C and 190 degrees C in steps of 10 degrees C), studies had been performed in order to get information about the thermal stability of the interstitial boron and interstitial oxygen defect in 50-Omega cm material after irradiation with 23-GeV protons to a fluence of 6.91 x 10(13) p/cm(2). The results are presented and discussed. Furthermore, the extracted data from TSC measurements are compared with the macroscopic properties derived from current-voltage and capacitance-voltage characteristics. In addition, the introduction rate of interstitial boron and interstitial oxygen defect as a function of the initial doping concentration was determined by exposing diodes with different resistivities (10, 50, 250, and 2 k Omega cm) to 23-GeV protons. These results are compared with data from TSC and deep-level transient spectroscopy measurements achieved by the team of the CERN-RD50 "Acceptor removal project."

Owing to its unique biological and physicochemical properties, hydroxyapatite (HAp) represents one of the most extensively studied biomaterials for biomedical applications. It is well known that Candida is currently one of the fungi frequently involved in the onset and development of post-implant infections and, owing to the appearance of antifungal resistance, it is quite difficult to treat despite all the tremendous efforts made in this regard by the scientific world. Therefore, in this context, we report for the first time in this paper, the development and characterization of europium-doped thin films (5EuHAp, x(Eu) = 0.05) on a Si substrate by a spin-coating method. The results of ultrasound (US), zeta (zeta) potential, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and Fourier-transform infrared spectroscopy (FTIR) studies are presented. The XRD studies conducted on 5EuHAp suspension revealed the nanometric dimensions of the particles and sample purity. In addition, a moderate stability of the 5EuHAp suspension was observed. XPS measurements revealed the presence of Eu 3d in the 5EuHAp thin films. In the SEM micrographs, the surface uniformity and the absence of the surface defects could be observed. Moreover, the results of the FTIR studies showed the presence of the vibrational bands specific to the HAp structure in the studied sample. The antifungal activity of the HAp and 5EuHAp suspensions and coatings was evaluated using the Candida albicans ATCC 10231 (C. albicans) fungal strain. The qualitative assays of the antifungal properties of HAp and 5EuHAp coatings were also visualized by SEM and CLSM. The antifungal studies revealed that both 5EuHAp suspensions and coatings exhibited noticeable antifungal activity against C. albicans cells.

In this work, thermoelectric properties of the nanocomposite materials produced via ball milling followed by spark plasma sintering from In0.2Yb0.2Co4Sb12 double filled skutterudite (SKT) with silicon and tungsten carbide inclusions are investigated. The nanocomposites with low volume ratios of beta-SiC and '-WC have a significantly increased power factor, while the lattice thermal conductivity is lowered only for beta-SiC composites. The power factor enhancement in '-WC/SKT composite compensates the increase of its thermal conductivity, and as a consequence, the maximum value of the figure of merit, 0.97, is attained for 0.33 v% 'WC at 450 degrees C, with 15% higher than that of the simple skutterudite sample. (c) 2021 Elsevier B.V. All rights reserved.