National Institute Of Materials Physics - Romania

A sensor for the enzymatic activity and inhibition of the 20S proteasome was developed by immobilizing the synthetic peptide ABZ-VVSYAMG-(O2Oc)2-OH at Au electrodes. The detection principle is based on the elec-troactivity of ABZ, part of the ABZ-VVSY-OH moiety released from the peptide upon 20S proteasome chymo-trypsin action. The peptide was immobilized on a para-amino thiophenol (PATP) self-assembled monolayer on Au electrode by cross-linking its amino group to the -(O2Oc)2-OH moiety of the peptide (Au/PATP/peptide). The immobilization of the peptide and its interaction with 20S proteasome was investigated by SEM, QCM, SPR, ATR-FTIR and electrochemistry. The activity of 20S proteasome was assessed electrochemically by cyclic voltammetry (CV) and electrochemical impedance spectra (EIS) after the immersion Au/PATP/peptide in 20S proteasome solution. CV study showed a decrease in both capacitive and faradaic currents corresponding to the ABZ-VVSY-OH removal, allowing the quantification of the 20S proteasome activity. The EIS study revealed that the resis-tance corresponding to charge transfer reactions at the peptide/solution interface correlated to the ABZ redox reaction, decreased linearly with increasing the incubation time in 20S proteasome solution. The perfected assay was applied for the investigation of the inhibitory effect of one synthetic, bortezomib, and two naturally occurring, epoxomicin, and lactacystin inhibitors.

This article's objective is the synthesis of new composites based on thermoplastic polyurethane (TPU) and TiO2 nanowires (NWs) as free-standing films, highlighting their structural and optical properties. The free-standing TPU-TiO2 NW films were prepared by a wet chemical method accompanied by a thermal treatment at 100 degrees C for 1 h, followed by air-drying for 2 h. X-ray diffraction (XRD) studies indicated that the starting commercial TiO2 NW sample contains TiO2 tetragonal anatase (A), cubic Ti0.91O (C), and orthorhombic Ti2O3 (OR), as well as monoclinic H2Ti3O7 (M). In the presence of TPU, an increase in the ratio between the intensities of the diffraction peaks at 43.4 degrees and 48 degrees belonging to the C and A phases of titanium dioxide, respectively, is reported. The increase in the intensity of the peak at 43.4 degrees is explained to be a consequence of the interaction of TiO2 NWs with PTU, which occurs when the formation of suboxides takes place. The variation in the ratio of the absorbance of the IR bands peaked at 765-771 cm(-1) and 3304-3315 cm(-1) from 4.68 to 4.21 and 3.83 for TPU and the TPU-TiO2 NW composites, respectively, with TiO2 NW concentration equal to 2 wt.% and 17 wt.%, indicated a decrease in the higher-order aggregates of TPU with a simultaneous increase in the hydrogen bonds established between the amide groups of TPU and the oxygen atoms of TiO2 NWs. The decrease in the ratio of the intensity of the Raman lines peaked at 658 cm(-1) and 635 cm(-1), which were assigned to the vibrational modes E-g in TiO2 A and E-g in H2Ti3O7 (ITiO2-A/I-H2Ti3O7), respectively, from 3.45 in TiO2 NWs to 0.94-0.96 in the TPU-TiO2 NW composites, which indicates that the adsorption of TPU onto TiO2 NWs involves an exchange reaction of TPU in the presence of TiO2 NWs, followed by the formation of new hydrogen bonds between the -NH- of the amide group and the oxygen atoms of TixO2x-mn, Ti2O3, and Ti0.91O. Photoluminescence (PL) studies highlighted a gradual decrease in the intensity of the TPU emission band, which is situated in the spectral range 380-650 nm, in the presence of TiO2 NW. After increasing the TiO2 NW concentration in the TPU-TiO2 NW composite mass from 0 wt.% to 2 wt.% and 17 wt.%, respectively, a change in the binding angle of the TPU onto the TiO2 NW surface from 12.6 degrees to 32 degrees and 45.9 degrees, respectively, took place.

In this paper, the stability of magnesium-doped hydroxyapatite/chitosan (MHC) suspension obtained with the sol-gel approach was evaluated using nondestructive ultrasound measurements. The MHC coatings obtained by the spin-coating technique were characterized before and after immersion for 7 and 14 days, respectively, in Dulbecco's modified eagle medium (DMEM) by scanning electron microscopy, equipped with an EDAX detector. Also, the functional groups present on the MHC coatings surface were analyzed with the aid of attenuated total reflection (ATR) Fourier transform infrared (FTIR) spectroscopy. The surface microstructure was evaluated using two commentary techniques, namely atomic force microscopy (AFM) and metallographic microscopy (MM). The influence of immersion in DMEM on the biological properties was studied with in vitro studies using primary osteoblast and HCT-8 cell lines. Our results revealed that both surface morphology and chemical composition of the MHC coatings allow rapid development of a new apatite layer on their surface after immersion in DMEM. Preliminary in vitro biological studies underlined the noncytotoxic effect of the studied samples on the proliferation of primary osteoblast and HCT-8 cell lines, which makes them a promising candidate for applications in fields such as orthopedics or dentistry. The antifungal assay of the MHC coatings was assessed using Candida albicans ATCC 10231 and their results showed a good inhibitory effect. The coatings made on the basis of the MHC composite could contribute to increasing the degree of success of implants by decreasing the risk of infections and postoperative inflammation.

This article's objective is the synthesis of new composites based on thermoplastic polyurethane (TPU) and TiO2 nanowires (NWs) as free-standing films, highlighting their structural and optical properties. The free-standing TPU-TiO2 NW films were prepared by a wet chemical method accompanied by a thermal treatment at 100 degrees C for 1 h, followed by air-drying for 2 h. X-ray diffraction (XRD) studies indicated that the starting commercial TiO2 NW sample contains TiO2 tetragonal anatase (A), cubic Ti0.91O (C), and orthorhombic Ti2O3 (OR), as well as monoclinic H2Ti3O7 (M). In the presence of TPU, an increase in the ratio between the intensities of the diffraction peaks at 43.4 degrees and 48 degrees belonging to the C and A phases of titanium dioxide, respectively, is reported. The increase in the intensity of the peak at 43.4 degrees is explained to be a consequence of the interaction of TiO2 NWs with PTU, which occurs when the formation of suboxides takes place. The variation in the ratio of the absorbance of the IR bands peaked at 765-771 cm(-1) and 3304-3315 cm(-1) from 4.68 to 4.21 and 3.83 for TPU and the TPU-TiO2 NW composites, respectively, with TiO2 NW concentration equal to 2 wt.% and 17 wt.%, indicated a decrease in the higher-order aggregates of TPU with a simultaneous increase in the hydrogen bonds established between the amide groups of TPU and the oxygen atoms of TiO2 NWs. The decrease in the ratio of the intensity of the Raman lines peaked at 658 cm(-1) and 635 cm(-1), which were assigned to the vibrational modes E-g in TiO2 A and E-g in H2Ti3O7 (ITiO2-A/I-H2Ti3O7), respectively, from 3.45 in TiO2 NWs to 0.94-0.96 in the TPU-TiO2 NW composites, which indicates that the adsorption of TPU onto TiO2 NWs involves an exchange reaction of TPU in the presence of TiO2 NWs, followed by the formation of new hydrogen bonds between the -NH- of the amide group and the oxygen atoms of TixO2x-mn, Ti2O3, and Ti0.91O. Photoluminescence (PL) studies highlighted a gradual decrease in the intensity of the TPU emission band, which is situated in the spectral range 380-650 nm, in the presence of TiO2 NW. After increasing the TiO2 NW concentration in the TPU-TiO2 NW composite mass from 0 wt.% to 2 wt.% and 17 wt.%, respectively, a change in the binding angle of the TPU onto the TiO2 NW surface from 12.6 degrees to 32 degrees and 45.9 degrees, respectively, took place.

Iron oxide nanoparticles are one of the most promising tools for theranostic applications of pancreatic cancer due to their unique physicochemical and magnetic properties making them suitable for both diagnosis and therapy. Thus, our study aimed to characterize the properties of dextran-coated iron oxide nanoparticles (DIO-NPs) of maghemite (gamma-Fe2O3) type synthesized by co-precipitation and to investigate their effects (low-dose versus high-dose) on pancreatic cancer cells focusing on NP cellular uptake, MR contrast, and toxicological profile. This paper also addressed the modulation of heat shock proteins (HSPs) and p53 protein expression as well as the potential of DIO-NPs for theranostic purposes. DIO-NPs were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), dynamic light scattering analyses (DLS), and zeta potential. Pancreatic cancer cells (PANC-1 cell line) were exposed to different doses of dextran-coated gamma-Fe2O3 NPs (14, 28, 42, 56 mu g/mL) for up to 72 h. The results revealed that DIO-NPs with a hydrodynamic diameter of 16.3 nm produce a significant negative contrast using a 7 T MRI scanner correlated with dose-dependent cellular iron uptake and toxicity levels. We showed that DIO-NPs are biocompatible up to a concentration of 28 mu g/mL (low-dose), while exposure to a concentration of 56 mu g/mL (high-dose) caused a reduction in PANC-1 cell viability to 50% after 72 h by inducing reactive oxygen species (ROS) production, reduced glutathione (GSH) depletion, lipid peroxidation, enhancement of caspase-1 activity, and LDH release. An alteration in Hsp70 and Hsp90 protein expression was also observed. At low doses, these findings provide evidence that DIO-NPs could act as safe platforms in drug delivery, as well as antitumoral and imaging agents for theranostic uses in pancreatic cancer.

Presently, iron oxide nanoparticles are the only ones approved for clinical use as contrast agents in magnetic resonance imaging (MRI). Even though there is a high demand for these types of nanoparticles both for clinical use as well as for research, there are difficulties in obtaining stable nanoparticles with reproducible properties. In this context, in this study, we report the obtaining by an adapted coprecipitation method of dextran-coated maghemite nanoparticles (gamma-Fe2O3 NPs). The morphology and structure of the dextran-coated maghemite nanoparticles (gamma-Fe2O3 NPs) were determined using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The TEM and SEM micrographs highlighted the obtaining of particles of nanometric size and spherical shape morphology. Furthermore, the high-resolution transmission electron microscopy (HRTEM), as well as selected area diffraction (SAED), revealed that the obtained samples presented the structure of cubic maghemite. In this study, we also explored the effects of the co-precipitation synthesized dextran-coated maghemite nanoparticles (gamma-Fe2O3 NPs) on the redox status of macrophages. For cytotoxicity evaluation of these NPs, murine macrophages (RAW 264.7 cell line) were exposed to different concentrations of dextran-coated maghemite nanoparticles (gamma-Fe2O3 NPs) corresponding to 0-500 mu g Fe3+/mL and incubated for 24, 48, and 72 h. Intracellular iron uptake, changes in the oxidative stress parameters (reactive oxygen species production and malondialdehyde level), and the activity of antioxidant enzymes, as well as GSH concentration in cells, were evaluated after incubation with a lower (50 mu g Fe3+/mL) and higher (500 mu g Fe3+/mL) dose of NPs. The results indicated a significant decrease in RAW 264.7 cell viability after 72 h in the presence of NPs at concentrations above 25 mu g Fe3+/mL. An important accumulation of NPs, dependent on dose and exposure time, was detected in macrophages, but it induced only a limited raise in the oxidative status. We showed here that the antioxidant capacity of RAW 264.7 macrophages was efficient in counteracting dextran-coated maghemite nanoparticles (gamma-Fe2O3 NPs) toxicity even at higher doses.

Green nanotechnology is a rapidly growing field linked to using the principles of green chemistry to design novel nanomaterials with great potential in environmental and health protection. In this work, metal and semiconducting particles (AuNPs, AgClNPs, ZnO, AuZnO, AgClZnO, and AuAgClZnO) were phytosynthesized through a "green" bottom-up approach, using burdock (Arctium lappa L.) aqueous extract. The morphological (SEM/TEM), structural (XRD, SAED), compositional (EDS), optical (UV-Vis absorption and FTIR spectroscopy), photocatalytic, and bio-properties of the prepared composites were analyzed. The particle size was determined by SEM/TEM and by DLS measurements. The phytoparticles presented high and moderate physical stability, evaluated by zeta potential measurements. The investigation of photocatalytic activity of these composites, using Rhodamine B solutions' degradation under solar light irradiation in the presence of prepared powders, showed different degradation efficiencies. Bioevaluation of the obtained composites revealed the antioxidant and antibacterial properties. The tricomponent system AuAgClZnO showed the best antioxidant activity for capturing ROS and ABTS center dot(+) radicals, and the best biocidal action against Escherichia coli, Staphylococcus aureus and Pseudomonas aeruginosa. The "green" developed composites can be considered potential adjuvants in biomedical (antioxidant or biocidal agents) or environmental (as antimicrobial agents and catalysts for degradation of water pollutants) applications.

Usually, before being used in biomedical applications, a biomaterials' bioactivity is tested by in vitro methods that simulate similar conditions to those found in the human body. In this work, we report on the synthesis of zinc-doped hydroxyapatite-chitosan (ZnHApC) composite coatings by the vacuum deposition method. The surface microstructure and the chemical and molecular modification of the coatings before and after soaking in DMEM (Dulbecco's Modified Eagle's Medium) were studied. For this objective, techniques such as attenuated total reflection (ATR), Fourier transform infrared (FTIR) spectroscopy, metallographic microscopy (MM), and scanning electron microscopy (SEM) were applied used. Also, water contact angle measurements and swelling studies were made on ZnHApC composite coatings before and after soaking in a biological medium. The coatings' adherence to the substrate was also studied. The results of antifungal studies on ZnHApC composite coatings against the Candida albicans microbial strain reveal their good antifungal activity. The biocompatibility of the composite coatings was tested using a primary osteoblast cell line. Our results suggest that zinc-doped hydroxyapatite-chitosan samples could be used as a bioimplant material due to their enhanced bioactivity and biocompatibility.

A novel electrochemical biosensor was developed to monitor fibroblast cells stress levels for the first time in situ under external stimuli based on the recognition of superoxide anion released upon cell damage. The biosensor comprised metallized polycaprolactone electrospun fibers covered with zinc oxide for improved cell adhesion and signal transduction, whilst stable bioconjugates of mercaptobenzoic acid-functionalized gold nanoparticles/ superoxide dismutase were employed as recognition bioelements. Biosensors were first tested and optimized for in situ generated superoxide detection by fixed potential amperometry at +0.3 V, with minimal interferences from electroactive species in cell culture media. L929 fibroblast cells were then implanted on the optimized biosensor surface and the biosensor morphologically characterized by scanning electron microscopy (SEM) and fluorescence microscopy, which illustrated the network-type pattern of fibroblasts adjacent to the fiber scaffold. Fibroblast stress was induced by zymosan and monitored at the cells integrated biosensor using fixed potential amperometry (CA) with a sensitivity of 26 nA cm-2 mu g mL-1 zymosan and electrochemical impedance spectros-copy (EIS), with similar sensitivity of the biosensor considering the Rs and Z' parameters of around 0.13 omega cm2 mu g-1 mL and high correlation factors R2 of 0.9994. The obtained results underline the applicability of the here developed biosensor for the electrochemical screening of the fibroblast cells stress. The concept in using low-cost biocompatible polymeric fibers as versatile scaffolds for both enzyme immobilization and cell adhesion, opens a new path in developing biosensors for the in-situ investigation of a variety of cellular events.

The microscopic mechanism of the occurrence of ferroelectric properties in M-type barium hexaferrites is investigated by experimental and first-principle computation methods. The analysis of magnetic, X-ray, and Mossbauer measurements of BaFe12O19 samples ascertains the correlation between the thermal factor in the process of annealing samples and their functional properties. The occurrence of the remnant polarization in barium hexaferrites at room temperature contradicts the description of their crystal structure in the fra-mework of centrosymmetric space group P63/mmc (No. 194), in which one of the symmetry operations is inversion center. Therefore, the crystal structure of BaFe12O19 was analyzed in the frameworks of SG P63/mmc (No. 194) and non-centrosymmetric SG P63mc (No. 186). The computed value of polarization for a non-centrosymmetric unit cell is similar to 3.5 mu C/cm2. The analysis of polarization was carried out on a path connecting the polar P63mc and non-polar P63/mmc structures and considered in terms of the total energy barrier. Our result allows ascertaining a direct relationship between the remnant polarization of the unit cell and the broken spatial-inversion symmetry in the crystal structure of M-type barium hexaferrite.(c) 2022 Elsevier B.V. All rights reserved.