National Institute Of Materials Physics - Romania

Anode modification with carbon nanomaterials is an important strategy for the improvement of microbial fuel cell (MFC) performance. The presence of nitrogen in the carbon network, introduced as active nitrogen functional groups, is considered beneficial for anode modification. In this aim, nitrogen-containing carbon nanostructures (NCNs) with different morphologies were obtained via carbonization of polyaniline and were further investigated as anode modifiers in MFCs. The present study investigates the influence of NCN morphology on the changes in the anodic microbial community and MFC performance. Results show that the nanofibrillar morphology of NCNs is beneficial for the improvement of MFC performance, with a maximum power density of 40.4 mW/m(2), 1.25 times higher than the anode modified with carbonized polyaniline with granular morphology and 2.15 times higher than MFC using the carbon cloth-anode. The nanofibrillar morphology, due to the well-defined individual nanofibers separated by microgaps and micropores and a better organization of the carbon network, leads to a larger specific surface area and higher conductivity, which can allow more efficient substrate transport and better bacterial colonization with greater relative abundances of Geobacter and Thermoanaerobacter, justifying the improvement of MFC performance.

Pure and Er-doped hematite (alpha-Fe2O3) nanorods were prepared by a two-step method involving hydrothermal synthesis and calcination of pure and Er-doped goethite (alpha-FeOOH) nanorods. Substitution of Fe3+ by Er3+ in the crystal structure of hematite caused morpho-structural changes such as expansion of the unit cell and gradual shortening and rounding of hematite nanorods towards formation of nanoellipsoids. These changes induced modification of magnetic and optical properties suggesting the possibility of a systematic control of physical properties via rare earth substitution. A decrease in the hyperfine magnetic field, coercive field and Morin transition temperature, as well as an increase of the magnetic susceptibility and a narrowing of the optical band gap were observed by substitution. Intimate mechanisms related to the formation of more and more defect-like hematite phases with decreased temperatures for the transition to the low temperature antiferromagnetic phase at increased doping level were evidenced via temperature dependent Mo center dot ssbauer spectroscopy.

Sesquipedalian mud and burnt bricks (second to third century AD) were excavated from the Roman city of Romula located in the Lower Danube Region (Olt county, Romania). Along with local soils, bricks are investigated by petrographic analysis, X-ray fluorescence (XRF), X-ray diffraction (XRD), Fourier transformed infrared spectroscopy (FT-IR), electron microscopy (SEM/EDX), X-ray microtomography (XRT), thermal analysis (DTA-TG), M.ssbauer spectroscopy, magnetometry, colorimetry, and mechanical properties assessment. The results correlate well with each other, being useful for conservation/restoration purposes and as reference data for other ceramic materials. Remarkably, our analysis and comparison with literature data indicate possible control and wise optimization by the ancient brickmakers through the recipe, design (size, shape, and micro/ macrostructure), and technology of the desired physical-chemical-mechanical properties. We discuss the Roman bricks as materials that can adapt to external factors, similar, to some extent, to modern "smart" or "intelligent" materials. These features can explain their outstanding durability to changes of weather/climate and mechanical load.

Magnetic nanoparticles (MNPs) have evolved tremendously during recent years, in part due to the rapid expansion of nanotechnology and to their active magnetic core with a high surface-to-volume ratio, while their surface functionalization opened the door to a plethora of drug, gene and bioactive molecule immobilization. Taming the high reactivity of the magnetic core was achieved by various functionalization techniques, producing MNPs tailored for the diagnosis and treatment of cardiovascular or neurological disease, tumors and cancer. Superparamagnetic iron oxide nanoparticles (SPIONs) are established at the core of drug-delivery systems and could act as efficient agents for MFH (magnetic fluid hyperthermia). Depending on the functionalization molecule and intrinsic morphological features, MNPs now cover a broad scope which the current review aims to overview. Considering the exponential expansion of the field, the current review will be limited to roughly the past three years.

Intermetallic Cr-Al-C thin films from the 211 class of MAX phases were fabricated via ion beam deposition and structural investigations were undertaken to obtain information about morpho-structural effects propelled by carbon excess in the stoichiometry of the films. In order to promote the occurrence of the Cr2AlC MAX phase, the stoichiometric thin films were subsequently annealed at two temperature values: 650 degrees C and 700 degrees C in UHV conditions for 30 min. The morpho-structural effects in both as-deposited and annealed films were monitored using scanning electron microscopy, X-ray diffraction, and Raman spectroscopy. XRD analysis showed that the as-deposited sample was almost completely crystallized in the hexagonal Cr2AlC structure, with a remaining amorphous fraction of about 17%, most probably rich in carbon. Raman analysis allowed the identification of three spectral regions, two of them encompassing the Raman optical modes belonging to the Cr2AlC 211 MAX phase, while the third one gave strong evidence of highly intense and large D- and G-bands of carbon. Structural parameters such as the crystal lattice parameters as well as the volume of the crystal unit cell were found to decrease upon annealing; this decrease is attributed to the grain growth. The average crystallite dimension was proven to increase after annealing, while the lattice micro-strain lowered to approximately 63% in the annealed thin film compared to the as-deposited one. Well-formed and intense Raman peaks attributed to D- and G-bands of carbon were also observed and, corroborated with the structural data, seemed to indicate an overall increased level of crystal ordering as well as potential carbon nanoclustering after thermal treatments with thin Cr2AlC films. This observed phenomenon concords with previously documented reports on ab initio modelling of possible Cr2AlC structures with carbon excess.

The manipulation of magnetic anisotropy represents the fundamental prerequisite for the application of magnetic materials. Here we present the vectorial magnetic properties of nanostructured systems and thin films of Fe and FeCo prepared on linearly trenched Mo templates with thermally controlled periodicity. The magnetic properties of the nanosystems are engineered by tuning the shape, size, thickness, and composition parameters of the thin films. Thus, we control coercivity, magnetization, orientation of the easy axis of magnetization, and the long-range magnetic order of the system in the function of the temperature. We distinguish magnetic components that emerge from the complex morpho-structural features of the undulating Fe or FeCo nanostructured films on trenched Mo templates: (i) assembly of magnetic nanowires and (ii) assembly of magnetic islands/clusters. Uniaxial anisotropy at room temperature was proven, characterized, and explained in the case of all systems. Our work contributes to the understanding of magnetic properties necessary for possible further applications of linear systems and undulated thin films.

In this work, we report the preparation of nanostructured electrodes based on dense arrays of vertically-aligned copper (Cu) nanowires (NWs) to be subsequently covered by cadmium telluride (CdTe) thin films, with great potential to be used within "substrate"-type photovoltaic cells based on A(II)-BVI heterojunctions. In particular, the multi-step preparation protocol presented here involves an electrochemical synthesis procedure within a supported anodic aluminum oxide (AAO) nanoporous template for first generating a homogeneous array of vertically-aligned Cu NWs, which are then further embedded within a compact CdTe thin film. In a second stage, we tested three deposition methods (vacuum thermal evaporation, VTE; radio-frequency magnetron sputtering, RF-MS; and electrochemical deposition, ECD) for use in obtaining CdTe layers potentially able to consistently penetrate the previously prepared Cu NWs array. A comparative analysis was performed to critically evaluate the morphological, optical, and structural properties of the deposited CdTe films. The presented results demonstrate that under optimized processing conditions, the ECD approach could potentially allow the cost-effective fabrication of absorber layer/collecting electrode CdTe/Cu nanostructured interfaces that could improve charge collection mechanisms, which in turn could allow the fabrication of more efficient solar cells based on A(II)-BVI semiconducting compounds.

Direct current (DC) and radio frequency (RF) magnetron sputtering methods were selected for conducting the deposition of structural materials, namely ceramic and metallic co-depositions. A total of six configurations were deposited: single thin layers of oxides (Cr2O3, SiO2) and co-deposition configurations (50:50 wt.%) as structural materials (W, Be)-(Cr2O3, SiO2), all deposited on 304L stainless steel (SS). A comprehensive evaluation such as surface topology, thermal desorption outgassing, and structural/chemical state was performed. Moreover, mechanical characterization evaluating properties such as adherence, nano indentation hardness, indentation modulus, and deformation relative to yielding, was performed. Experimental results show that, contrary to SiO2 matrix, the composite layers of Cr2O3 with Be and W exhibit surface smoothing with mitigation of artifacts, thus presenting a uniform and compact state with the best microstructure. These results are relevant in order to develop future dense coatings to be used in the fusion domain.

We report in this paper on the monolayer composites thin films that have the magnetic spinel CoFe2O4 and the piezoelectric perovskite BNT-BT0.08 as constituent phases. Composite thin films of CoFe2O4 and BNT-BT0.08, with molar ratios of 0.5:1, 1:1 and 1.5:1, have been deposited by spin coating method from a sol precursor, mixture type, of CoFe2O4 and BNT-BT0.08. The monolayer thin films, deposited on Si/SiO2/TiO2/Pt substrate, were characterized using selected methods, such as: X-ray diffraction, scanning electron microscopy, atomic force microscopy/piezoelectric force microscopy, dielectric spectroscopy, and vibrating sample magnetometer. X-ray diffraction demonstrated the two phases: cubic CoFe2O4 and rhombohedral BNT-BT0.08. Furthermore, the Si/ SiO2/TiO2/Pt/BNT-BT0.08/CoFe2O4 monolayers show a simultaneous enhancement of both the magnetization and coercivity with the increase of the magnetic phase, accompanied by a decrease of the dielectric constant. The obtained results reveal that the investigated monolayer structures present superior properties compared to those of bilayer composites.