National Institute Of Materials Physics - Romania

Magnetism and Superconductivity

Facilities and Services

For preparation of materials by wet chemistry methods. Includes fume hood Biobase, heating mantle Winkler, magnetic stirrer with hot plate Heidolph, home manufactured autoclave, oven for heat treatment in gas flow. Characteristics: –  fume hood exhaust volume 800 m3/ h –  fume hood intake air velocity (8 velocity steps, >0.50 m/s) –  magnetic stirrer hotplate […]

View

The 8000M Mixer/Mill is a high-energy ball mill that grinds between 0.3 – 10 grams of samples, depending of density. The complex movement (8 shape figure) allows obtaining high energy. Characteristics: – 875 cycles per minute – dry or wet milling  –  sample size per vial: up to 10 ml for grinding tough samples and […]

View

Freeze dryer Biobase BK-FD 12T allows extracting water from organic or inorganic materials (powders, bulk or solutions) by sublimation at low temperatures. Characteristics: –  Cold trap temperature -80 0C –  Vacuum degree < 10 Pa  –  Drying area: 0.075 m2 –  Water capture capability: 3 kg / 24 h –  Tray Layer: 3 –  Loading […]

View

For sample manipulation in controlled atmosphere (low concentration of oxygen and humidity) Characteristics: –  concentration of oxygen below 1 ppm –  concentration of water vapor (moisture) below 1 ppm –  possibility of in-situ regeneration of the molecular sieve catalyst used for removal of oxygen and moisture – automatic adjustment of pressure inside glove box within […]

View

For investigation of gas-solid reaction kinetics and thermodynamics (Pressure-composition Isotherms) during formation/decomposition of hydrides, nitrides, etc by Sievert (volumetric) method. Characteristics:   – Type of gas: hydrogen, nitrogen, inert gases. Not oxygen or corrosive gases             –   Pressure range measurements: from 0.01 atm up to 135 atm –   Temperature range: 30 0C – 450 0C or […]

View

The compact EASYHEAT induction heating systems are a reliable solution for heating parts with a quick, clean source of heat. With a movable work head that can be located up to 3m (10’) from the power supply, it is ideal for repeatable, non-contact heating of parts. Equipped to operate over a broad frequency range (150-400 […]

View

The PlasmaQuant® MS Spectrometer, manufactured by Analytik Jena is extremely reliable – able to run any sample matrix from waste water to organic solvents. The integrated aerosol dilution allows direct analysis of high TDS samples. Simply dilute samples online. The highly efficient RF system of the PlasmaQuant® MS produces a virtually center-grounded, stable and robust […]

View

The Pulsed Laser Deposition (PLD) work station is manufactured by SURFACE systems+technology GmbH & Co. KG and is used for preparation of epitaxial thin films, especially advanced oxide layers, having the major advantage of stoichiometric material transfer from a target to the substrate. Characteristics: -2 deposition chambers, each with 4-target carousels; – KrF excimer laser […]

View

Main characteristics:  Front loading Useful hot zone: ∅=4″ h=5″ within +/- 10 C can be used both as “hot press” or classic sintering Maximum batch furnace temperature: 2300 C Maximum “hot press” temperature: 2200 C  Increasing temperature at 100 C/min. Max. stroke force 100 kN, above 1000 C Max. stroke distance: 4″ with ΔF = […]

View

Main characteristics:  Front loading Work space: 135 mm x 135 mm x 135 mm 6 magnetrons, maximum power 4.8 kW Frequency: 2450 MHz Maximum sintering temperature: 1700 C (limited by insulation parameters) Ar, N2 sintering or vacuum (~10-3 mbar) Temperature measurement by pyrometer Maximal temperature and heating ratio depend mostly on the heated material properties […]

View

1 2 3


Back to top

Copyright © 2022 National Institute of Materials Physics. All Rights Reserved