National Institute Of Materials Physics - Romania

Cu-doped hydroxyapatite (CuHAp) thin films were obtained using spin coating method. To make these thin films, CuHAp suspensions obtained by sol-gel method were used. The coatings obtained were thermally treated at 500 degrees C. After the thermal treatment, the thin films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM). Moreover, the stability of the suspensions before being used to obtain the thin films was certified by dynamic light scattering (DLS), zeta potential methods and ultrasound measurements. In the XRD patterns, the peaks associated with hexagonal hydroxyapatite were identified in accordance with JCPDS no. 09-0432. EDS and XPS results confirmed the presence of Cu ions in the samples. Data about the morphological features and chemical composition of CuHAp thin films were obtained by performing scanning electron microscopy (SEM) measurements. Our results suggest that the CuHAp thin films surface is continuous and homogenous. The presence of the functional groups in the CuHAp thin films was confirmed by Fourier-transform infrared spectroscopy (FTIR) and Raman spectroscopy studies. Information about the surface topography of the CuHAp thin films has been obtained using atomic force microscopy (AFM). The AFM images determined that the surface topography of the CuHAp thin layer is homogenous and continuous without presenting any unevenness or fissures. The cytotoxicity of CuHAp thin films was assessed using human gingival fibroblasts (HGF-1) cells. The results of the cell viability assays demonstrated that the thin films presented good biocompatible properties towards the HGF-1 cells. Additionally, the adherence and development of HGF-1 cells on the surface of CuHAp thin films were determined using AFM. The AFM surface topographies highlighted that the CuHAp thin film's surface favored the attachment and proliferation of HGF-1 cells on their surface.

In the current study, a porous composite material, hydroxyapatite/chitosan/microcrystalline-cellulose (CaHAp-CS-MCC), was successfully prepared and used for the adsorption of Eriochrome Black T (EBT) from water. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), differential thermal analysis (DTA), thermogravimetric analysis (TGA), specific surface area (SSA), and atomic force microscope (AFM) were used to evaluate the physicochemical properties of the prepared adsorbents. CaHAp-CS-MCC exhibited a decrease in crystallinity and reduction in crystallite size. CaHAp-CS-MCC surface exhibited cracks and pores. AFM displayed changes in surface micro-texture of CaHAp, formation of new surface structures, and variations in particle size and distribution. Upon grafting CaHAp with CS and MCC, its specific surface area decreased from 139.224 to 11.775 m2/g. BET suggested that filling CaHAp pores by CS and MCC contributed to the reduction in surface area. The pore volume values decreased from 2.56 x 10-1 (CaHAp) to 3.91 x 10-2 cm3/g (CaHAp-CS-MCC). Adsorption equilibrium was reached at about 40 min. The adsorption capacities values of CaHAp-CS-MCC and CaHAp were equal to 248 mg/g and 92 mg/g, respectively. The pseudo-second order and the Langmuir equations fitted well the adsorption phenomenon. The calculated thermodynamic parameters showed an exothermic and non-spontaneous system.

In the present work, we report the synthesis and investigations of La0.9K0.1MnO3 and La0.8K0.1Pb0.1MnO3 bulk samples which could be potential magnetocaloric materials for magnetic refrigeration close to room temperature. A flash combustion reaction and sintering at 1200 degrees C for 10 h are used to prepare the bulk materials. Both compounds crystallized into a rhombohedral structure with R3\documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\overline{3 }$$\end{document}c space group confirmed by X-ray powder diffraction results. Scanning electron microscopy analysis, combined with XRD peak profiles is performed to estimate the particle/crystallite size of the samples. Moreover, the Curie temperature, TC, is found to be higher in lead-rich sample due to the enhancement of the grain size and the Mn3+-O-Mn4+ double exchange (DE) interaction. Therefore, the bulk sample La0.8K0.1Pb0.1MnO3 shows a room temperature phase transition of 289 K as well as a higher saturation magnetization. The La0.8K0.1Pb0.1MnO3 bulk compound exhibits a high and sharp peak in magnetic entropy change up to 5.5 Jkg-1 K-1 under 5 T at the magnetic transition temperature TC. To compare the magnetocaloric performances of the studied compounds, relative cooling power (RCP) was employed. The obtained experimental results revealed that the increase in particle size influences severely the magnetocaloric properties.

This research targets the need for eco-friendly strategies in the synthesis of bioactive materials, addressing the importance of valorization of vegetal waste. This study focuses on developing biohybrids containing biomimetic lipid vesicles and phytosynthesized gold-silver chloride nanoparticles (AuAgCl NPs) derived from Achillea millefolium L. extract. By leveraging the natural antioxidant and antimicrobial properties of the plant, the research proposes a sustainable approach to creating materials with potential biomedical applications. The biomimetic membranes were loaded with chlorophyll a, a natural spectral marker. Three types of bioactive materials (biohybrids) were developed by varying the lipid vesicle/AuAgCl NP ratio. Optical (UV-Vis, fluorescence emission, FTIR), structural (XRD), elemental (EDX, XPS), and morphological (TEM) studies were performed to characterize the bio-developed materials. The hydrophobic/hydrophilic characteristics of the samples were investigated by measuring the water contact angle, and their size was estimated by DLS and TEM. Zeta potential measurements were used to evaluate the physical stability of phyto-developed particles. Antioxidant properties of phyto-particles were investigated through the chemiluminescence technique. The obtained biomaterials exhibited high antioxidant activity and antiproliferative activity against HT-29 and B-16 cancer cells. Therapeutic index values were calculated for each biohybrid. Additionally, the bio-prepared hybrids revealed biocidal action against Staphylococcus aureus and Enterococcus faecalis. The phyto-developed biomaterials are promising in biomedical applications, particularly as adjuvants in cancer therapy.

Nowadays, the development of devices based on organic materials is an interesting research challenge. The performance of such devices is strongly influenced by material selection, material properties, design, and the manufacturing process. Usually, buckminsterfullerene (C60) is employed as electron transport material in organic photovoltaic (OPV) devices due to its high mobility. However, considering its low solubility, there have been many attempts to replace it with more soluble non-fullerene compounds. In this study, bulk heterojunction thin films with various compositions of zinc phthalocyanine (ZnPc), a perylene diimide derivative, or C60 were prepared by matrix-assisted pulsed laser evaporation (MAPLE) technique to assess the influence of C60 replacement on fabricated heterostructure properties. The investigations revealed that the optical features and the electrical parameters of the organic heterostructures based on this perylene diimide derivative used as an organic acceptor were improved. An increase in the JSC value (4.3 x 10-4 A/cm2) was obtained for the structures where the perylene diimide derivative acceptor entirely replaced C60 compared to the JSC value (7.5 x 10-8 A/cm2) for the heterostructure fabricated only with fullerene. These results are encouraging, demonstrating the potential of non-fullerene compounds as electron transport material in OPV devices.

Among many iron-based superconductors, isovalently substituted BaFe2(As1-xPx)2 displays, for x approximate to 0.3, apart from the quite usual Second Magnetization Peak (SMP) in the field dependence of the critical current density, an unusual peak effect in the temperature dependence of the critical current density in the constant field, which is related to the rhombic-to-square (RST) structural transition of the Bragg vortex glass (BVG). By using multi-harmonic AC susceptibility investigations in three different cooling regimes-field cooling, zero-field cooling, and field cooling with measurements during warming up-we have discovered the existence of a temperature region in which there is a pronounced magnetic memory effect, which we attributed to the direction of the structural transition. The observed huge differences in the third harmonic susceptibility at low and high AC frequencies indicates the difference in the time-scale of the structural transition in comparison with the timescale of the vortex excitations. Our findings show that the RST influence on the vortex dynamics goes beyond the previously observed influence on the onset of the SMP.

Background/Objectives: A biocomposite based on magnesium-doped hydroxyapatite and enriched with amoxicillin (MgHApOx) was synthesized using the coprecipitation method and is presented here for the first time. Methods: The stability of MgHAp and MgHApOx suspensions was evaluated by ultrasound measurements. The structure of the synthesized MgHAp and MgHApOx was examined with X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The crystalline structure was determined by X-ray diffraction. The FTIR data were collected in the range of 4000-400 cm-1. The morphology of the nanoparticles was evaluated by scanning electron microscopy (SEM). Furthermore, the biocompatible properties of MgHAp, MgHApOx and amoxicillin (Ox) suspensions were assessed using human fetal osteoblastic cells (hFOB 1.19 cell line). The antimicrobial properties of the MgHAp, MgHApOx and Ox suspension nanoparticles were assessed using the standard reference microbial strains Staphylococcus aureus ATCC 25923, Escherichia coli ATCC 25922 and Candida albicans ATCC 10231. Results: X-ray studies have shown that the biocomposite retains the characteristics of HAp and amoxicillin. The SEM assessment exhibited that the apatite contains particles at nanometric scale with acicular flakes morphology. The XRD and SEM results exhibited crystalline nanoparticles. The average crystallite size calculated from XRD analysis increased from 15.31 nm for MgHAp to 17.79 nm in the case of the MgHApOx sample. The energy-dispersive X-ray spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) analysis highlighted the presence of the constituent elements of MgHAp and amoxicillin. Moreover, XPS confirmed the substitution of Ca2+ ions with Mg2+ and the presence of amoxicillin constituents in the MgHAp lattice. The results of the in vitro antimicrobial assay demonstrated that MgHAp, MgHApOx and Ox suspensions exhibited good antimicrobial activity against the tested microbial strains. The results showed that the antimicrobial activity of the samples was influenced by the presence of the antibiotic and also by the incubation time. Conclusions: The findings from the biological assays indicate that MgHAp and MgHApOx are promising candidates for the development of new biocompatible and antimicrobial agents for biomedical applications.

The development of thin films of chromium-doped hydroxyapatite (20CrHAp) deposited on silicon substrate by the spin coating method was realized for the first time. A coherent investigation of the physicochemical properties of 20CrHAp thin films was also carried out for the first time. The obtained thin films were studied by various techniques such as, scanning electron microscopy (SEM), atomic force microscopy (AFM), Fourier transform infrared spectroscopy (FTIR) investigations and fractal analysis. By scanning electron microscopy (SEM) studies were obtained valuable information about the surface morphology of the 20CrHAp thin films. The zeta potential (ZP), Dynamic light scattering (DLS) and ultrasound measurements (US) were used in order to evaluate the stability of 20CrHAp suspension. The ratio between the hydrodynamic diameter obtained by DLS and the particle diameter obtained by SEM was 1.6. The SEM results on 20CrHAp thin films suggested that the sample possess a conglomerate of nanoparticles unevenly distributed on their surface. The surface morphology of the 20CrHAp thin films was studied with the aid of atomic force microscopy (AFM). The AFM topography of the 20CrHAp thin film's surface highlighted that the thin films present the morphology of a continuum deposited layer composed of non-uniform particle conglomerates. The presence of hydroxyapatite on the surface of silicium effects on the development of the fungal cells on their surface. Furthermore, our investigation delves into the

Recently, much research has focused on the search for new mixed donor-acceptor layers for applications in organic electronics. Organic heterostructures with layers based on the generation 1 poly(propylene thiophenoimine) (G1PPT) dendrimer, N,N '-diisopropylnaphthalene diimide (MNDI), and a combination of the two were prepared and their electrical properties were investigated. Single layers of G1PPT and MNDI and a mixed layer (G1PPT:MNDI) were obtained via spin coating on quartz glass, silicon, and glass/ITO substrates, using chloroform as a solvent. The absorption mechanism was investigated, the degree of disorder was estimated, and the emission properties of the layers were highlighted using spectroscopic methods (UV-Vis transmission and photoluminescence). The effects of the concentration and surface topographical particularities on the properties of the layers were analyzed via atomic force microscopy. All of the heterostructures realized with ITO and Au electrodes showed good conduction, with currents of the order of mA. Additionally, the heterostructure with a mixed layer exhibited asymmetry in the current-voltage curve between forward and reverse polarization in the lower range of the applied voltages, which was more significant at increased concentrations and could be correlated with rectifier diode behavior. Consequently, the mixed-layer generation 1 poly(propylene thiophenoimine) dendrimer with N,N '-diisopropylnaphthalene diimide can be considered promising for electronic applications.