National Institute Of Materials Physics - Romania

The scope of this study consists of setting up of an integrated cost-effective sampling & laboratory analyses procedure which delineates sampling, sub-sampling and analytical uncertainties in case of fine-grained extractive waste deposits. This procedure is designed to support the decision makers towards fine-grained waste deposits upcycling and land reclamation. This procedure consists of a balanced replicated sampling design (BRSD) coupled with a three split levels ANOVA data processing. The paper provides the readership with the mathematical backgrounds of the three split level ANOVA analysis (3L-ANOVA) and an Excel algorithm for its implementation. Also, the paper presents an example of implementation of the developed methods in the case of a Romanian iron ore tailings (IOT) old pond. The findings of the paper consist of: a) argues, based on OM, SEM-EDS, XRFS and XRD observations, that classical TOS is ineffective for fine-grained waste deposits; b) BRSD in conjunction with 3L-ANOVA analysis is the only approach fit for reliable characterization of the fine-grained stockpiles; c) sampling uncertainty is the critical factor of the uncertainty budget of the analyte concentration; d) Lilliefors approach is adequate for the hypothesis testing where or not the measurand is normal distributed; e) The outcomes of the BRDSD&3L-ANOVA investigations carried on Teliuc tailings, estimated at circa 5.5* 106 m3, consist mainly of mineral quantification at lot level i.e. quartz-54% (+/- 7%), hematite-15% (+/- 3%), calcite-11% (+/- 3%), MgO 3% (+/- 1%), Al2O3 9% (+/- 2%). The concentrations of some CRMs like Ti, V, Ba, Y, W were found at ACE limits and their associated relative expanded uncertainties overpass 50%. Thus, the expanded uncertainties clearly depict the reliability of acquired data for the decision makers regarding waste valorization. f) The IOT into Teliuc can be upcycled as minerals for cement and ceramic industries as well as for geopolymer manufacture. Also, IOT can be downcycles as filler in road construction and mine closure. Finally, the Teliuc yard can be rehabilitated with zero-waste left behind. The data exactness provided by this procedure can be increased to any desirable level through increasing the number of collected items, but the cost of sampling and analyses increases proportionally. In such circumstances, the posted approach can be tailored at the stakeholder request as to safely underpin the decision to turn fine-grained by-products into valuable secondary resources, facilitating a greater circularity of the mining industry.

The diffusion of iodide defects has been considered the most important degradation mechanism of methylammonium lead iodide (MAPI) in solar cells. The present study demonstrates the importance of the pressure inside this material on the dynamics of iodide defects, using molecular dynamics simulations. It is known that the diffusion coefficient of an iodide vacancy is an order of magnitude higher than that of interstitial iodide. We show that this difference systematically increases with increased tensile strain and that both diffusion coefficients tend to zero when a compressive strain is applied. This result suggests that compression of the MAPI can be a good solution to reduce its degradation rate. Besides, the statistical aspect of deriving the diffusion coefficient from the mean squared displacement (MSD) is discussed in terms of the initial conditions (positions and velocities) of the atoms and the simulation time, considering different seeds of the pseudorandom number generator used in the simulations performed with the LAMMPS software.

Novel biomaterials with promising bone regeneration potential, derived from rich, renewable, and cheap sources, are reported. Thus, thin films were synthesized from marine-derived (i.e., from fish bones and seashells) hydroxyapatite (MdHA) by pulsed laser deposition (PLD) technique. Besides the physical-chemical and mechanical investigations, the deposited thin films were also evaluated in vitro using dedicated cytocompatibility and antimicrobial assays. The morphological examination of MdHA films revealed the fabrication of rough surfaces, which were shown to favor good cell adhesion, and furthermore could foster the in-situ anchorage of implants. The strong hydrophilic behavior of the thin films was evidenced by contact angle (CA) measurements, with values in the range of 15-18 degrees. The inferred bonding strength adherence values were superior (i.e., similar to 49 MPa) to the threshold established by ISO regulation for high-load implant coatings. After immersion in biological fluids, the growth of an apatite-based layer was noted, which indicated the good mineralization capacity of the MdHA films. All PLD films exhibited low cytotoxicity on osteoblast, fibroblast, and epithelial cells. Moreover, a persistent protective effect against bacterial and fungal colonization (i.e., 1- to 3-log reduction of E. coli, E. faecalis, and C. albicans growth) was demonstrated after 48 h of incubation, with respect to the Ti control. The good cytocompatibility and effective antimicrobial activity, along with the reduced fabrication costs from sustainable sources (available in large quantities), should, therefore, recommend the MdHA materials proposed herein as innovative and viable solutions for the development of novel coatings for metallic dental implants.

Replacing lead atoms in halide perovskite materials is of significant importance for the development of environmentally friendly perovskite solar cells. In this paper, we investigated the effect of doping the MAPbI(2.6)Cl(0.4) hybrid perovskite (MA-methyl ammonium) with non-toxic elements, such as alkaline earth metal ions (Mg2+) and transition metal ions (Zn2+). The structural, morphological, and optical properties of the prepared samples were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and UV-Vis. spectroscopy. Finally, the doped films were used as photoactive layers in solar devices in order to evaluate their photovoltaic performance. Zn proved to be more appropriate to replace partially Pb and films with higher quality were obtained. As a result, the MAPb1(-x)Zn(x)I(2.6)Cl(0.4) based solar cells have demonstrated a slight improvement of the photovoltaic performances, resulting in a uniform and narrower PCEs (power conversion efficiency) range, compared to pristine MAPbI(2.6)Cl(0.4) based devices.

Replacing lead atoms in halide perovskite materials is of significant importance for the development of environmentally friendly perovskite solar cells. In this paper, we investigated the effect of doping the MAPbI(2.6)Cl(0.4) hybrid perovskite (MA-methyl ammonium) with non-toxic elements, such as alkaline earth metal ions (Mg2+) and transition metal ions (Zn2+). The structural, morphological, and optical properties of the prepared samples were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and UV-Vis. spectroscopy. Finally, the doped films were used as photoactive layers in solar devices in order to evaluate their photovoltaic performance. Zn proved to be more appropriate to replace partially Pb and films with higher quality were obtained. As a result, the MAPb1(-x)Zn(x)I(2.6)Cl(0.4) based solar cells have demonstrated a slight improvement of the photovoltaic performances, resulting in a uniform and narrower PCEs (power conversion efficiency) range, compared to pristine MAPbI(2.6)Cl(0.4) based devices.

Sub-stochiometric nickel oxide (NiOx) films were investigated as a hole selective contact option in silicon (Si) heterojunction solar cells. Numerical simulations were carried out to evaluate the impacts of the NiOx electronic properties variations and the NiOx/Si interface defect density (D-it) on device performance. Simulation data suggest that the best performance is achievable for wide bandgaps (E-g) and corresponding high valence band edge (E-VB) positions in the NiOx films. Overall, in simulations, the performance remains practically unchanged for the nickel vacancy concentrations [V-Ni] = 10(17)-10(21 )cm(-3), assuming high E-VB and low D-it. The experimental data measured using NiOx films prepared by radio-frequency magnetron sputtering reveal that the increase in [V-Ni] lifts the conductivity, concurrently decreasing E-g and E-VB. As a result, we concluded that the performance of the fabricated sputtered NiOx/Si heterojunction solar cell is limited by high D-it as well as narrow E-g and low E-VB.

Sodium hexatitanate (Na2Ti6O13) nanoparticles have been synthesized by the hydrothermal method with microwave and conven-tional heating, after which their photocatalytic properties toward an azo dye pollutant degradation have been investigated. Insights into the dynamics and reactivity of the species involved in the photocatalytic mechanism of the (Na2Ti6O13) samples were precisely investigated, for the first time, by X-band electron paramagnetic resonance (EPR) spectroscopy under different experimental conditions. X-ray diffraction structural analysis revealed that all samples crystallized in a monoclinic C2/m structure, with different short-range structural order according to the employed heating, as indicated by Raman. Field-emission scanning electron microscopy and transmission electron microscopy results revealed the formation of rod-and fiber-like nanoparticles with different diameters and lengths. EPR measurements indicated the presence of different Ti3+ point defects and F centers in the samples. X-ray photoelectron spectroscopy analysis proved the presence of oxygen-related defects, but no Ti3+ was detected on the surface. Spin trapping experiments monitored the generation of hydroxyl (OH center dot) radicals over UV-irradiation time. Various parameters contribute to the photocatalytic activity of the samples; however, the type of defect and particle morphology appeared as key factors for enhanced efficiency. Our study provides significant information about paramagnetic defects in Na2Ti6O13 materials and their role in photocatalysis to design other Ti-based photocatalysts.

The development of new thin-film cathodes triggered a recent research interest in energy storage applications. Over the past years, vanadium oxides have been extensively explored as promising electrodes for batteries owing to their rich valence states and remarkable electrochemical properties. Herein, we report on the synthe-sis of undoped and Sn doped V2O3 thin-films on graphene (G)/Al foil by pulsed laser deposition followed by rapid thermal annealing in N2 at low temperature (similar to 430 degrees C). The obtaining V2O3 phase on graphene/Al foil (G/Al) has been confirmed by X-ray diffraction and Raman and X-ray photoelectron spectroscopy analyses. The synthesized vanadium oxide films were tested as cathodes in coin cells. The electrochemical properties have been systematically investigated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and galvanostatic charge discharge (GCD) measurements. A superior electrochemical performance was observed for the V2O3 on G/Al structures, with an initial capacity of around 300 mAh g-1, with respect to the bare G/Al electrode. The use of the Sn-doped (5 mol%) V2O3 thin-films improved slightly the initial capac-ity up to a value of ca. 311 mAh g-1. Both V2O3/G/Al and Sn-doped V2O3/G/Al exhibited excellent cycling performances after 40 cycles with a capacity maintenance at a C-rate C/20 of 317 mAh g-1. Long-term cycling test (up to 200 cycles) showed that the Sn doping could be an excellent strategy to improve the stability of the electrodes, which yielded a capacity loss of only 0.128% per cycle. Possible mechanisms are presented and dis-cussed. This work could serve as point of reference for future developments in the field of batteries employing vanadium oxide-based thin-films deposited by physical vapor deposition techniques.

Cu2NiSnS4 (CNTS) absorber layers are elaborated by electrodeposition at various applied potentials followed by sulfurization treatment at 450 degrees C under sulfur atmosphere. The microstructural investigations revealed the presence of Cu4SnS4 secondary phases which can be reduced using an applied potential of -1.15 V vs. Ag/AgCl. Using the corresponding cathodic potential for Ni2+, the competing detrimental hydrogen evolution regresses the morphology and composition. The film with the highest Ni concentration has a band gap of 1.44 eV as inferred from diffuse reflectance data. The Randles cell model is probed by electrochemical impedance spectroscopy.

Sodium hexatitanate (Na2Ti6O13) nanoparticles have been synthesized by the hydrothermal method with microwave and conven-tional heating, after which their photocatalytic properties toward an azo dye pollutant degradation have been investigated. Insights into the dynamics and reactivity of the species involved in the photocatalytic mechanism of the (Na2Ti6O13) samples were precisely investigated, for the first time, by X-band electron paramagnetic resonance (EPR) spectroscopy under different experimental conditions. X-ray diffraction structural analysis revealed that all samples crystallized in a monoclinic C2/m structure, with different short-range structural order according to the employed heating, as indicated by Raman. Field-emission scanning electron microscopy and transmission electron microscopy results revealed the formation of rod-and fiber-like nanoparticles with different diameters and lengths. EPR measurements indicated the presence of different Ti3+ point defects and F centers in the samples. X-ray photoelectron spectroscopy analysis proved the presence of oxygen-related defects, but no Ti3+ was detected on the surface. Spin trapping experiments monitored the generation of hydroxyl (OH center dot) radicals over UV-irradiation time. Various parameters contribute to the photocatalytic activity of the samples; however, the type of defect and particle morphology appeared as key factors for enhanced efficiency. Our study provides significant information about paramagnetic defects in Na2Ti6O13 materials and their role in photocatalysis to design other Ti-based photocatalysts.