National Institute Of Materials Physics - Romania

We reported on the sequential development of a high-operative photocatalyst with penta-component inorganic bulk heterojunction for improved charge trapping characteristics at particle-particle interfaces for enhanced solar light-driven photocatalytic degradation of active tetracycline antibiotic. Structural, morphological, optical, and electronic properties of the synthesized samples were investigated using a series of complementary char-acterization techniques, such as XRD, FE-SEM, HR-TEM, XPS, as well as hard and soft XAS in both total electron yield (TEY) and fluorescence yield (TFY). For the case of the carbon composite material, SrTiO3@NiFe2O4@-Fe0@Ni0@CNTs, a reduced crystallinity when compared to the starting support material was noticed, although this translated into a significant improvement of the morphology and the photocatalytic performance. The SrTiO3@NiFe2O4@Fe0@Ni0@CNTs fibrous photocatalyst can efficiently achieve a high-to-total degradation of tetracycline antibiotic under visible light irradiation in less than two hours, following a non-linear PFO kinetic model with an apparent reaction rate of about 0.0606 min-1 and an 98% photodegradation activity. The XPS and XAS analysis demonstrated unequivocally the appearance of nanoscale zero-valent iron (Fe0) and zero-valent nickel (Ni0) on the photocatalyst surface, which facilitates the separation of photogenerated e+ and h+ pairs, and the appearance of more active sites.

The aim of this work is to highlight the influence of blends based on TiO2 nanoparticles and reduced graphene oxide (RGO) on the photodegradation of acetaminophen (AC). To this end, the catalysts of TiO2/RGO blends with RGO sheet concentrations equal 5, 10, and 20 wt. % were prepared by the solid-state interaction of the two constituents. The preferential adsorption of TiO2 particles onto the RGO sheets' surfaces via the water molecules on the TiO2 particle surface was demonstrated by FTIR spectroscopy. This adsorption process induced an increase in the disordered state of the RGO sheets in the presence of the TiO2 particles, as highlighted by Raman scattering and scanning electron microscopy (SEM). The novelty of this work lies in the demonstration that TiO2/RGO mixtures, obtained by the solid-phase interaction of the two constituents, allow an acetaminophen removal of up to 95.18% after 100 min of UV irradiation. This TiO2/RGO catalyst induced a higher photodegradation efficiency of AC than TiO2 due to the presence of RGO sheets, which acted as a capture agent for the photogenerated electrons of TiO2, hindering the electron-hole recombination. The reaction kinetics of AC aqueous solutions containing TiO2/RGO blends followed a complex first-order kinetic model. Another novelty of this work is the demonstration of the ability of PVC membranes modified with Au nanoparticles to act both as filters for the removal of TiO2/RGO blends after AC photodegradation and as potential SERS supports, which illustrate the vibrational properties of the reused catalyst. The reuse of the TiO2/RGO blends after the first cycle of AC photodegradation indicated their suitable stability during the five cycles of pharmaceutical compound photodegradation.

The aim of this work is to highlight the influence of blends based on TiO2 nanoparticles and reduced graphene oxide (RGO) on the photodegradation of acetaminophen (AC). To this end, the catalysts of TiO2/RGO blends with RGO sheet concentrations equal 5, 10, and 20 wt. % were prepared by the solid-state interaction of the two constituents. The preferential adsorption of TiO2 particles onto the RGO sheets' surfaces via the water molecules on the TiO2 particle surface was demonstrated by FTIR spectroscopy. This adsorption process induced an increase in the disordered state of the RGO sheets in the presence of the TiO2 particles, as highlighted by Raman scattering and scanning electron microscopy (SEM). The novelty of this work lies in the demonstration that TiO2/RGO mixtures, obtained by the solid-phase interaction of the two constituents, allow an acetaminophen removal of up to 95.18% after 100 min of UV irradiation. This TiO2/RGO catalyst induced a higher photodegradation efficiency of AC than TiO2 due to the presence of RGO sheets, which acted as a capture agent for the photogenerated electrons of TiO2, hindering the electron-hole recombination. The reaction kinetics of AC aqueous solutions containing TiO2/RGO blends followed a complex first-order kinetic model. Another novelty of this work is the demonstration of the ability of PVC membranes modified with Au nanoparticles to act both as filters for the removal of TiO2/RGO blends after AC photodegradation and as potential SERS supports, which illustrate the vibrational properties of the reused catalyst. The reuse of the TiO2/RGO blends after the first cycle of AC photodegradation indicated their suitable stability during the five cycles of pharmaceutical compound photodegradation.

The phosphate KCoCr-(PO4)(2) and iron-substitutedvariants KCoCr1-x Fe x (PO4)(2) (x =0.25, 0.5, and 0.75) were synthesized by a solid-state reaction route,while a high substitution level of Fe was achieved. Their structureswere refined using powder X-ray diffraction and indexed in a monoclinicsystem with a P2(1)/n spacegroup. A 3D framework with six-sided tunnels parallel to the [101]direction was formed in which the K atoms are located. Mo''ssbauerspectroscopy confirms the exclusive presence of octahedral paramagneticFe(3+) ions, with isomer shifts increasing slightly with x substitution. Electron paramagnetic resonance spectroscopyconfirmed the presence of paramagnetic Cr3+ ions. The activationenergy, determined by dielectric measurements, shows that the iron-containingsamples present higher ionic activity. Relative to the electrochemicalactivity of K, these materials could be good candidates for positiveand/or negative electrode materials for energy storage applications. The synthesized phosphate KCoCr-(PO4)(2) and Fe-substituted variants KCoCr1-x Fe x (PO4)(2) (x = 0.25, 0.5, and 0.75) present a 3D frameworkwith six-sided tunnels in which the K atoms are located. The activationenergy, determined by dielectric measurements, shows that the iron-containingsamples present improved ionic activity, making these materials goodcandidates for positive and/or negative electrode materials for energystorage applications.

Historically, titanium dioxide (TiO2) has been one of the most extensively studied metal oxide photocatalysts; however, it suffers from a large bandgap and fast charge recombination. We report the use of green, rapid, single-step continuous hydrothermal flow synthesis for the preparation of TiO2, and TiO2 hybrids with reduced graphene oxide (rGO) and/or N-doped carbon quantum dots (NCQDs) with significant enhancement in photocatalytic activity. Using a solar light generator under ambient conditions with no extra oxygen gas added, we observed the evolution reaction of the model pollutant (methylene blue) in real time. Tailoring of the light absorption to match that of the solar spectrum was achieved by a combination of materials of nano-TiO2 hybrids of nitrogen-doped carbon quantum dots and graphene in its reduced form with a photocatalytic rate constant of ca. 25 x 10(-5) s(-1). Using a diversity of state-of-the-art techniques including high-resolution transmission electron microscopy, transient photoluminescence, X-ray photoelectron spectroscopy and high accuracy, sophisticated hybrid density functional theory calculations we have gained substantial insight into the charge transfer and modulation of the energy band edges of anatase due to the presence of graphene or carbon dots, parameters which play a key role in improving drastically the photocatalytic efficiencies when compared to pristine titania. More importantly, we prove that a combination of features and materials displays the best photocatalytic behaviour. This performance is delivered in a greener synthetic process that not only produces photocatalytic materials with optimised properties and tailored visible light absorption and efficiency but also provides a path to industrialization.

Historically, titanium dioxide (TiO2) has been one of the most extensively studied metal oxide photocatalysts; however, it suffers from a large bandgap and fast charge recombination. We report the use of green, rapid, single-step continuous hydrothermal flow synthesis for the preparation of TiO2, and TiO2 hybrids with reduced graphene oxide (rGO) and/or N-doped carbon quantum dots (NCQDs) with significant enhancement in photocatalytic activity. Using a solar light generator under ambient conditions with no extra oxygen gas added, we observed the evolution reaction of the model pollutant (methylene blue) in real time. Tailoring of the light absorption to match that of the solar spectrum was achieved by a combination of materials of nano-TiO2 hybrids of nitrogen-doped carbon quantum dots and graphene in its reduced form with a photocatalytic rate constant of ca. 25 x 10(-5) s(-1). Using a diversity of state-of-the-art techniques including high-resolution transmission electron microscopy, transient photoluminescence, X-ray photoelectron spectroscopy and high accuracy, sophisticated hybrid density functional theory calculations we have gained substantial insight into the charge transfer and modulation of the energy band edges of anatase due to the presence of graphene or carbon dots, parameters which play a key role in improving drastically the photocatalytic efficiencies when compared to pristine titania. More importantly, we prove that a combination of features and materials displays the best photocatalytic behaviour. This performance is delivered in a greener synthetic process that not only produces photocatalytic materials with optimised properties and tailored visible light absorption and efficiency but also provides a path to industrialization.

The phosphate KCoCr-(PO4)(2) and iron-substitutedvariants KCoCr1-x Fe x (PO4)(2) (x =0.25, 0.5, and 0.75) were synthesized by a solid-state reaction route,while a high substitution level of Fe was achieved. Their structureswere refined using powder X-ray diffraction and indexed in a monoclinicsystem with a P2(1)/n spacegroup. A 3D framework with six-sided tunnels parallel to the [101]direction was formed in which the K atoms are located. Mo''ssbauerspectroscopy confirms the exclusive presence of octahedral paramagneticFe(3+) ions, with isomer shifts increasing slightly with x substitution. Electron paramagnetic resonance spectroscopyconfirmed the presence of paramagnetic Cr3+ ions. The activationenergy, determined by dielectric measurements, shows that the iron-containingsamples present higher ionic activity. Relative to the electrochemicalactivity of K, these materials could be good candidates for positiveand/or negative electrode materials for energy storage applications. The synthesized phosphate KCoCr-(PO4)(2) and Fe-substituted variants KCoCr1-x Fe x (PO4)(2) (x = 0.25, 0.5, and 0.75) present a 3D frameworkwith six-sided tunnels in which the K atoms are located. The activationenergy, determined by dielectric measurements, shows that the iron-containingsamples present improved ionic activity, making these materials goodcandidates for positive and/or negative electrode materials for energystorage applications.

Active and stable materials that utilize solar radiation for promoting different reactions are critical for emerging technologies. Two of the most common polymeric carbon nitrides were prepared by the thermal polycondensation of melamine. The scope of this work is to investigate possible structural degradation before and after photoelectrochemical testing. The materials were characterized using synchrotron radiation and lab-based techniques, and subsequently degraded photoelectrochemically, followed by post-mortem analysis. Post-mortem investigations reveal: (1) carbon atoms bonded to three nitrogen atoms change into carbon atoms bonded to two nitrogen atoms and (2) the presence of methylene terminals in post-mortem materials. The study concludes that polymeric carbon nitrides are susceptible to photoelectrochemical degradation via ring opening.

Using the microwave-assisted sol-gel method, Zn- and Cu-doped TiO2 nanoparticles with an anatase crystalline structure were prepared. Titanium (IV) butoxide was used as a TiO2 precursor, with parental alcohol as a solvent and ammonia water as a catalyst. Based on the TG/DTA results, the powders were thermally treated at 500 degrees C. XRD and XRF revealed the presence of a single-phase anatase and dopants in the thermally treated nanoparticles. The surface of the nanoparticles and the oxidation states of the elements were studied using XPS, which confirmed the presence of Ti, O, Zn, and Cu. The photocatalytic activity of the doped TiO2 nanopowders was tested for the degradation of methyl-orange (MO) dye. The results indicate that Cu doping increases the photoactivity of TiO2 in the visible-light range by narrowing the band-gap energy.

Using the microwave-assisted sol-gel method, Zn- and Cu-doped TiO2 nanoparticles with an anatase crystalline structure were prepared. Titanium (IV) butoxide was used as a TiO2 precursor, with parental alcohol as a solvent and ammonia water as a catalyst. Based on the TG/DTA results, the powders were thermally treated at 500 degrees C. XRD and XRF revealed the presence of a single-phase anatase and dopants in the thermally treated nanoparticles. The surface of the nanoparticles and the oxidation states of the elements were studied using XPS, which confirmed the presence of Ti, O, Zn, and Cu. The photocatalytic activity of the doped TiO2 nanopowders was tested for the degradation of methyl-orange (MO) dye. The results indicate that Cu doping increases the photoactivity of TiO2 in the visible-light range by narrowing the band-gap energy.