National Institute Of Materials Physics - Romania

In this study, we report the performance improvement of wound dressings by covering them with magnetite-based nanostructured coatings. The magnetite nanoparticles (Fe3O4 NPs) were functionalized with Nigella sativa (N. sativa) powder/essential oil and dicloxacillin and were synthesized as coatings by matrix assisted pulsed laser evaporation (MAPLE). The expected effects of this combination of materials are: (i) to reduce microbial contamination, and (ii) to promote rapid wound healing. The crystalline nature of core/shell Fe3O4 NPs and coatings was determined by X-ray diffraction (XRD). Differential Scanning Calorimetry (DSC) and Thermo Gravimetric Analysis (TGA) have been coupled to investigate the stability and thermal degradation of core/shell nanoparticle components. The coatings' morphology was examined by scanning electron microscopy (SEM). The distribution of chemical elements and functional groups in the resulting coatings was evidenced by Fourier transform infrared (FTIR) spectrometry. In order to simulate the interaction between wound dressings and epithelial tissues and to evaluate the drug release in time, the samples were immersed in simulated body fluid (SBF) and investigated after different durations of time. The antimicrobial effect was evaluated in planktonic (free-floating) and attached (biofilms) bacteria models. The biocompatibility and regenerative properties of the nanostructured coatings were evaluated in vitro, at cellular, biochemical, and the molecular level. The obtained results show that magnetite-based nanostructured coatings functionalized with N. sativa and dicloxacillin are biocompatible and show an enhanced antimicrobial effect against Gram positive and Gram negative opportunistic bacteria.

The p-n junctions are the building blocks of nowadays electronic devices. The n- or p-type conductivity is obtained in classic semiconductors, like Si, by doping with atoms acting as donors or acceptors, respectively. Doping was used in ferroelectrics to influence the transition temperature, magnitude of some physical properties, but not necessarily conduction type. Therefore, comprehensive studies to obtain true ferroelectric p-n junctions by controlled doping are missing. Recently, it has been shown that Pb(Zr0.2Ti0.8)O-3 films doped with & AP;1% atomic Nb (n-type doping) or Fe (p-type doping) have different orientations of polarization in the as-grown state. Knowing that polarization orientation depends on doping type, the next step is to build ferroelectric p-n homojunctions and to study their properties in relation to ferroelectric polarization. p-n and n-p structures were grown for this purpose by successive deposition of Nb-doped and Fe-doped Pb(Zr,Ti)O-3 layers with different thicknesses. We find that these p-n homojunctions are ferroelectric, but the magnitude of the polarization and coercive field, as well as the dominant polarization orientation in the as-grown state, depend on the conduction type of the first grown layer. The I-V characteristics are quasi-linear, although the interfaces with the electrodes behaves as Schottky contacts. The resistance extracted from the I-V characteristics displays an exponential dependence on temperature, with an activation energy in the range of 0.14-0.17 eV. These results are explained assuming that the total current in the junction is the total of electron and hole injections at the electrode interfaces. It is shown that for relatively low doping concentrations, the current density contains a dominant term with a linear voltage dependence and an exponential temperature dependence, as observed experimentally, and a secondary (correction) term that is dependent on the free carrier density and can induce non-linear voltage dependence when this density is significant.

Glassy nanocomposites containing Yb3+/Er3+-doped GdF3 and LiGdF4 nanocrystals have been prepared by controlled crystallization of the xerogel and the structural, up-conversion luminescence, and magnetic properties were analyzed and discussed. Structural and morphological analysis showed uniform distribution of both GdF3 and LiGdF4 nanocrystals (tens of nm size), embedded in silica glass matrix as the result of thermal decomposition of the trifluoracetates, revealed as a strong exothermic peak at about 300 degrees C; the Li-ions co-doping showed a strong influence on the GdF3 and LiGdF4 nanocrystalline fraction. The energy dispersive spectrometry mapping showed Gd, F and Yb, Er within the nanocrystals but not in the silica glass matrix. X-ray diffraction pattern analysis indicated the crystalline lattice distortion consistent with the Yb/Er incorporation in both fluoride nanocrystals. The "green" ((H-2(11/2), S-4(3/2)) -> I-4(15/2)) and "red" (F-4(9/2)-> I-4(15/2)) up-conversion luminescences at 525, 545, and 660 nm observed under 980 nm laser light pumping were assigned to the Er3+ ions deexcitation through a two-photon process. The magnetic properties of the nanocomposite are strongly temperature dependent. The magnetization hysteresis loops show a ferromagnetic behavior at low temperatures (5K) related to the rare-earth ions contribution and the saturation magnetization of 39 emu/g. At 300 K a paramagnetic behavior was observed that was ascribed to the non-interacting localized nature of the magnetic moment of the rare-earth ions. Hence, such novel, multifunctional magnetic and optical materials can allow the intertwining between magnetism and photonics and might offer new opportunities for new magneto-optical device development.

The p-n junctions are the building blocks of nowadays electronic devices. The n- or p-type conductivity is obtained in classic semiconductors, like Si, by doping with atoms acting as donors or acceptors, respectively. Doping was used in ferroelectrics to influence the transition temperature, magnitude of some physical properties, but not necessarily conduction type. Therefore, comprehensive studies to obtain true ferroelectric p-n junctions by controlled doping are missing. Recently, it has been shown that Pb(Zr0.2Ti0.8)O-3 films doped with & AP;1% atomic Nb (n-type doping) or Fe (p-type doping) have different orientations of polarization in the as-grown state. Knowing that polarization orientation depends on doping type, the next step is to build ferroelectric p-n homojunctions and to study their properties in relation to ferroelectric polarization. p-n and n-p structures were grown for this purpose by successive deposition of Nb-doped and Fe-doped Pb(Zr,Ti)O-3 layers with different thicknesses. We find that these p-n homojunctions are ferroelectric, but the magnitude of the polarization and coercive field, as well as the dominant polarization orientation in the as-grown state, depend on the conduction type of the first grown layer. The I-V characteristics are quasi-linear, although the interfaces with the electrodes behaves as Schottky contacts. The resistance extracted from the I-V characteristics displays an exponential dependence on temperature, with an activation energy in the range of 0.14-0.17 eV. These results are explained assuming that the total current in the junction is the total of electron and hole injections at the electrode interfaces. It is shown that for relatively low doping concentrations, the current density contains a dominant term with a linear voltage dependence and an exponential temperature dependence, as observed experimentally, and a secondary (correction) term that is dependent on the free carrier density and can induce non-linear voltage dependence when this density is significant.

In this study, we report the performance improvement of wound dressings by covering them with magnetite-based nanostructured coatings. The magnetite nanoparticles (Fe3O4 NPs) were functionalized with Nigella sativa (N. sativa) powder/essential oil and dicloxacillin and were synthesized as coatings by matrix assisted pulsed laser evaporation (MAPLE). The expected effects of this combination of materials are: (i) to reduce microbial contamination, and (ii) to promote rapid wound healing. The crystalline nature of core/shell Fe3O4 NPs and coatings was determined by X-ray diffraction (XRD). Differential Scanning Calorimetry (DSC) and Thermo Gravimetric Analysis (TGA) have been coupled to investigate the stability and thermal degradation of core/shell nanoparticle components. The coatings' morphology was examined by scanning electron microscopy (SEM). The distribution of chemical elements and functional groups in the resulting coatings was evidenced by Fourier transform infrared (FTIR) spectrometry. In order to simulate the interaction between wound dressings and epithelial tissues and to evaluate the drug release in time, the samples were immersed in simulated body fluid (SBF) and investigated after different durations of time. The antimicrobial effect was evaluated in planktonic (free-floating) and attached (biofilms) bacteria models. The biocompatibility and regenerative properties of the nanostructured coatings were evaluated in vitro, at cellular, biochemical, and the molecular level. The obtained results show that magnetite-based nanostructured coatings functionalized with N. sativa and dicloxacillin are biocompatible and show an enhanced antimicrobial effect against Gram positive and Gram negative opportunistic bacteria.

Glassy nanocomposites containing Yb3+/Er3+-doped GdF3 and LiGdF4 nanocrystals have been prepared by controlled crystallization of the xerogel and the structural, up-conversion luminescence, and magnetic properties were analyzed and discussed. Structural and morphological analysis showed uniform distribution of both GdF3 and LiGdF4 nanocrystals (tens of nm size), embedded in silica glass matrix as the result of thermal decomposition of the trifluoracetates, revealed as a strong exothermic peak at about 300 degrees C; the Li-ions co-doping showed a strong influence on the GdF3 and LiGdF4 nanocrystalline fraction. The energy dispersive spectrometry mapping showed Gd, F and Yb, Er within the nanocrystals but not in the silica glass matrix. X-ray diffraction pattern analysis indicated the crystalline lattice distortion consistent with the Yb/Er incorporation in both fluoride nanocrystals. The "green" ((H-2(11/2), S-4(3/2)) -> I-4(15/2)) and "red" (F-4(9/2)-> I-4(15/2)) up-conversion luminescences at 525, 545, and 660 nm observed under 980 nm laser light pumping were assigned to the Er3+ ions deexcitation through a two-photon process. The magnetic properties of the nanocomposite are strongly temperature dependent. The magnetization hysteresis loops show a ferromagnetic behavior at low temperatures (5K) related to the rare-earth ions contribution and the saturation magnetization of 39 emu/g. At 300 K a paramagnetic behavior was observed that was ascribed to the non-interacting localized nature of the magnetic moment of the rare-earth ions. Hence, such novel, multifunctional magnetic and optical materials can allow the intertwining between magnetism and photonics and might offer new opportunities for new magneto-optical device development.

Featuring a high hydrogen storage content of up to 20 wt%, complex metal borohydrides remain promising solid state hydrogen storage materials, with the real prospect of reversible behavior for a zero-emission economy. However, the thermodynamic barriers and sluggish kinetics are still barriers to overcome. In this context, nanoconfinement has provided a reliable method to improve the behavior of hydrogen storage materials. The present work describes the thermodynamic and kinetic enhancements of LiBH4 nanoconfined in MFe2O4 (M=Co, Ni) ferrite-catalyzed graphene host. Composites of LiBH4-catalysts were prepared by melt infiltration and investigated by X-ray diffraction, TEM, STEM-EDS and TPD. The role of ferrite additives, metal precursor treatment (Ar, Ar/H-2) and the effect on hydrogen storage parameters are discussed. The thermodynamic parameters for the most promising composite LiBH4-graphene-NiFe2O4 (Ar) were investigated by Kissinger plot method, revealing an E-A = 127 kJ/mol, significantly lower than that of neat LiBH4 (170 kJ/mol). The reversible H-2 content of LiBH4-graphene-NiFe2O4 (Ar) after 5 a/d cycles was similar to 6.14 wt%, in line with DOE's target of 5.5 wt% storage capacity, while exhibiting the lowest desorption temperature peak of 349 degrees C. The composites with catalysts treated in Ar have lower desorption temperature due to better catalyst dispersion than using H-2/Ar.

The p-n junctions are the building blocks of nowadays electronic devices. The n- or p-type conductivity is obtained in classic semiconductors, like Si, by doping with atoms acting as donors or acceptors, respectively. Doping was used in ferroelectrics to influence the transition temperature, magnitude of some physical properties, but not necessarily conduction type. Therefore, comprehensive studies to obtain true ferroelectric p-n junctions by controlled doping are missing. Recently, it has been shown that Pb(Zr0.2Ti0.8)O-3 films doped with & AP;1% atomic Nb (n-type doping) or Fe (p-type doping) have different orientations of polarization in the as-grown state. Knowing that polarization orientation depends on doping type, the next step is to build ferroelectric p-n homojunctions and to study their properties in relation to ferroelectric polarization. p-n and n-p structures were grown for this purpose by successive deposition of Nb-doped and Fe-doped Pb(Zr,Ti)O-3 layers with different thicknesses. We find that these p-n homojunctions are ferroelectric, but the magnitude of the polarization and coercive field, as well as the dominant polarization orientation in the as-grown state, depend on the conduction type of the first grown layer. The I-V characteristics are quasi-linear, although the interfaces with the electrodes behaves as Schottky contacts. The resistance extracted from the I-V characteristics displays an exponential dependence on temperature, with an activation energy in the range of 0.14-0.17 eV. These results are explained assuming that the total current in the junction is the total of electron and hole injections at the electrode interfaces. It is shown that for relatively low doping concentrations, the current density contains a dominant term with a linear voltage dependence and an exponential temperature dependence, as observed experimentally, and a secondary (correction) term that is dependent on the free carrier density and can induce non-linear voltage dependence when this density is significant.

Photocatalytic conversion of H2O, CO2 and N-2 represents one promising approach to harvest and store solar energy, for which efficient visible light responsive semiconductors are inevitable. Often, the presence of a small amount of an additional component called a "cocatalyst", is required to synergistically enhance the performance of the photocatalyst. Tremendous efforts were made in the past to identify inexpensive materials to be used as cocatalysts, for which metal oxides (MOs) are one of the traditional choices. Among alternative categories of materials investigated, the recently discovered MXenes display enormous potential owing to their unique 2D layered structure, tuneable composition, abundant surface functionalities and superior electronic conductivity. Specifically, MOs and MXenes encompass a variety of distinct as well as analogous characteristics that allows them to be tailored to different extents. Unfortunately, a comprehensive overview covering the synthetic, structural and photocatalytic aspects of MOs and MXenes is not available as of now. Herein, we intend to summarize the progress achieved so far in these two families of materials to be used as cocatalysts for the photoconversion of H2O, CO2 and N-2. Followed by a general introduction, we briefly outline the fundamental principles and the role of cocatalysts in photocatalytic reactions. A discussion regarding the use of MOs and MXenes as cocatalysts for the conversion of H2O, CO2 and N-2 is then provided in separate sections. Critical assessment regarding structure and morphology control, surface properties and stability concerns can not only help to recognize the challenges that limit further advancement, but can also highlight the future research directions of these materials for the effective transformation of H2O, CO2 and N-2.

In this work, Tungsten(W)-doped TiO2 nanoparticles were synthesized using the sol-gel method and were used as electrode materials in supercapacitor applications. The structural and morphological properties of the prepared samples were analyzed by means of XRD, STEM, TEM, and XPS. The analysis of the defect centers was carried out using EPR spectroscopy. The electrochemical analysis of the assembled supercapacitor was done using cyclic voltammetry, galvanostatic cycling with potential limitation technique, potentiostatic electrochemical impedance spectroscopy, and voltage-holding experiments. All the presented samples showed paramagnetic defects in the EPR analysis, while 0.5% W-doped TiO2 showed a maximum signal intensity. The supercapacitor performance from the synthesized electrode material showed highly encouraging results. The equivalent series resistance (R-s) value for all the designs showed values under "1 omega,' which reflects high conductivity. As the maximum EPR intensity comes from TiO2 doped with 0.5% W, the supercapacitor performance of this sample was tested with a newly designed five-electrode system. This design showed superior performance compared to any other used designs with a specific capacitance of 25.5 F g(-1), with an energy density of 14.16 Wh kg (-1 )at 302 kW kg (-1).