National Institute Of Materials Physics - Romania

Two hybrid materials, based on 7-amino-4-(trifluoromethyl)coumarin and 7-amino-4-methyl-coumarin that attach covalently to graphene oxide (GO) have been synthesized in two steps: i) increasing the number of carboxyl groups required for functionalization with aminocoumarin derivatives by derivatization of the hydroxyls groups with chloroacetic acid, transforming GO into GO-COOH material; ii) activation of carboxylic groups using the carbodiimide-promoted reaction. The obtained composites were characterized by numerous methods that highlighted their successful obtaining. The antimicrobial activity was evaluated on resistant Mycobacterium tuberculosis strains, as well as on ESKAPE pathogens ((Enterococcus faecium, Staphylococcus aureus, Klebsiella pneumoniae, Acinetobacter baumannii, Pseudomonas aeruginosa, and Enterobacter spp.) in planktonic and biofilm growth states. The biocompatibility of the materials has been assayed using 3-(4, 5-dimethylthiazol-2-yl)2, 5-diphenyltetrazolium bromide assay as well as by measuring the level of nitric oxide/total reactive oxygen species and superoxide release in treated cells. The results have shown that materials exhibited improved inhibitory activity against resistant M. tuberculosis strains in comparison with GO, but also against planktonic and adherent strains. Also, the tested composites have been proved to be biocompatible on the MRC-5 fibroblast cells, demonstrating their promising potential to develop novel agents effective against multidrug resistant pathogens, including M. tuberculosis, as well as by the activation of a pro-inflammatory and of an oxidative response in the mammalian cells.

Hydrothermally formed mesoporous SnO2 was used as a support for nickel chemical deposition and, after subsequent thermal treatment, a high specific surface area (36 m(2) g(-1)) Ni/SnO2 material was obtained. XPS analysis has shown that in the Sn 3d region the spectrum is similar to that of pristine SnO2, whereas Ni species are present on the surface as NiO, Ni2O3 and Ni(OH)(2). Mixing Ni/SnO2 with a small amount of Black Pearls (BP) leads to a significant enhancement of the resulting Ni/SnO2-BP composite activity for nitrite anodic oxidation, presumably due to the higher surface area (115 m(2) g(-1)), to better electrical conductivity and to a certain contribution of the BP to an increase in surface density of the active sites. Ni/SnO2-BP also outperforms pristine BP (in terms of Tafel slopes and electron-transfer rates), most likely due to the fact that the Ni(ii)/Ni(iii) couple can act as an electrocatalyst for nitrite oxidation. A voltammetric method is proposed for the determination of nitrite, over a concentration range of three orders of magnitude (0.05 to 20 mM), with good reproducibility, high stability and excellent sensitivity. The high upper limit of the dynamic range of the analytically useful response might provide a basis for the reliable quantification of nitrite in wastewater.

Water and sunlight are the cleanest, most renewable, and abundant resources on Earth. Developing inexpensive, scalable photocatalysts that are highly stable for hydrogen (H-2) production has long been a cherished dream of humanity. Herein, we report on one-dimensional lepidocrocite-based sub-nanofilaments (NFs), approximate to 5 x 7 & Aring;(2) in cross-section, that generate H-2 from 80:20 v/v water/methanol mixtures when illuminated by simulated sunlight. The NFs were stable in the mixtures for times >4,300 h, 300 h of which were under irradiation. Apparent quantum yields as high as 11.7% were obtained. Based on deuterated water results, we conclude that water is the H-2 source. Further, no carbon dioxide (CO2) due to photocatalytic degradation of methanol was detected. Therefore, the NFs have strong green credentials and lucrative economic prospects for large scale up. We expect these NFs will lead to new lines for developing cheap and ultra-stable materials to produce H-2 photochemically for a long time.

Currently, the treatment of wounds is still a challenge for healthcare professionals due to high complication incidences and social impacts, and the development of biocompatible and efficient medicines remains a goal. In this regard, mesoporous materials loaded with bioactive compounds from natural extracts have a high potential for wound treatment due to their nontoxicity, high loading capacity and slow drug release. MCM-41-type mesoporous material was synthesized by using sodium trisilicate as a silica source at room temperature and normal pressure. The synthesized mesoporous silica was characterized by using Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), N2 absorption-desorption (BET), Dynamic Light Scattering (DLS) and Fourier transform infrared spectroscopy (FT-IR), revealing a high surface area (BET, 1244 m2/g); pore diameter of approx. 2 nm; and a homogenous, ordered and hexagonal geometry (TEM images). Qualitative monitoring of the desorption degree of the Salvia officinalis (SO) extract, rich in ursolic acid and oleanolic acid, and Calendula officinalis (CO) extract, rich in polyphenols and flavones, was performed via the continuous recording of the UV-VIS spectra at predetermined intervals. The active ingredients in the new composite MCM-41/sage and marigold (MCM-41/SO & CO) were quantified by using HPLC-DAD and LC-MS-MS techniques. The evaluation of the biological composites' activity on the wound site was performed on two cell lines, HS27 and HaCaT, naturally involved in tissue-regeneration processes. The experimental results revealed the ability to stimulate collagen biosynthesis, the enzymatic activity of the main metalloproteinases (MMP-2 and MMP-9) involved in tissue remodeling processes and the migration rate in the wound site, thus providing insights into the re-epithelializing properties of mesoporous composites.

[Cu(acac)(phen)(H2O)](ClO4) and [Cu(acac)(bipy)(H2O)](ClO4) catalysts were prepared by the immobilization of mixed-ligand complexes on graphene oxide derivatized with monochloroacetic acid. These catalysts were characterized through an ensemble of techniques including XRD, FTIR, Raman, and XPS while the catalytic behavior has been investigated in the oxidation of cyclohexene, 1-octene and glycerol in the presence of molecular oxygen. Cyclohexanone was the dominant product in the oxidation of cyclohexene resulting in selectivities higher than 50% for a conversion of 14.5%. The turnover frequencies were pretty high, namely, 4.5 h(-1) for [Cu(acac)(phen)(H2O)](ClO4) and 2.3 h(-1) for Cu(acac)(bipy)(H2O)](ClO4). The oxidation of 1-octene also occurred with a pretty high selectivity in 2-octanol as the main product. The role of copper in the oxidative dehydrogenation of glyceric acid towards tartronic acid was as well confirmed. Noteworthy, these catalysts were stable and their recycling occurred with no change in the conversion or selectivity.

Iron-doped Co3O4 oxides prepared by a surfactant-assisted method exhibited good catalytic activity in malic acid conversion, and the oxygen defects associated with the presence of Co2+ played a key role in catalyst activation for pyruvic acid production. The most active catalyst, for which the malic acid conversion was 70% and the pyruvic acid yield was 24%, has an inverse spinel type structure (Fe3+ replaces Co2+ from tetrahedral sites, while Fe2+ replaces Co3+ from octahedral sites) as well as a small energy difference between the highest occupied orbital and the lowest unoccupied orbital (low band-gap, E-g). The catalyst with the highest Co2+ loading showed the highest yield of pyruvic acid.

Photocatalytic conversion of H2O, CO2 and N-2 represents one promising approach to harvest and store solar energy, for which efficient visible light responsive semiconductors are inevitable. Often, the presence of a small amount of an additional component called a "cocatalyst", is required to synergistically enhance the performance of the photocatalyst. Tremendous efforts were made in the past to identify inexpensive materials to be used as cocatalysts, for which metal oxides (MOs) are one of the traditional choices. Among alternative categories of materials investigated, the recently discovered MXenes display enormous potential owing to their unique 2D layered structure, tuneable composition, abundant surface functionalities and superior electronic conductivity. Specifically, MOs and MXenes encompass a variety of distinct as well as analogous characteristics that allows them to be tailored to different extents. Unfortunately, a comprehensive overview covering the synthetic, structural and photocatalytic aspects of MOs and MXenes is not available as of now. Herein, we intend to summarize the progress achieved so far in these two families of materials to be used as cocatalysts for the photoconversion of H2O, CO2 and N-2. Followed by a general introduction, we briefly outline the fundamental principles and the role of cocatalysts in photocatalytic reactions. A discussion regarding the use of MOs and MXenes as cocatalysts for the conversion of H2O, CO2 and N-2 is then provided in separate sections. Critical assessment regarding structure and morphology control, surface properties and stability concerns can not only help to recognize the challenges that limit further advancement, but can also highlight the future research directions of these materials for the effective transformation of H2O, CO2 and N-2.

Replacing lead atoms in halide perovskite materials is of significant importance for the development of environmentally friendly perovskite solar cells. In this paper, we investigated the effect of doping the MAPbI(2.6)Cl(0.4) hybrid perovskite (MA-methyl ammonium) with non-toxic elements, such as alkaline earth metal ions (Mg2+) and transition metal ions (Zn2+). The structural, morphological, and optical properties of the prepared samples were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and UV-Vis. spectroscopy. Finally, the doped films were used as photoactive layers in solar devices in order to evaluate their photovoltaic performance. Zn proved to be more appropriate to replace partially Pb and films with higher quality were obtained. As a result, the MAPb1(-x)Zn(x)I(2.6)Cl(0.4) based solar cells have demonstrated a slight improvement of the photovoltaic performances, resulting in a uniform and narrower PCEs (power conversion efficiency) range, compared to pristine MAPbI(2.6)Cl(0.4) based devices.

Herein, a new direct synthesis route leading to a mesoporous NiWO4 with crystalline framework and NiWO4 -graphene nanoplatelets (GNP) composite is reported. Ni and W assembled into a mesoporous tungstate type of symmetry by co-precipitation synthesis route and its composite with GNP were used as supports for electrocatalysts, with reduced Pt content (8 wt.%), in oxygen reduction reaction (ORR) and hydrogen oxidation reaction (HOR) in acidic medium. A comprehensive assessment of the modifications related to the crystalline and porous structures, morphological aspects as well as the surface chemistry aiming to explain the electrochemical properties was performed. It was found that the presence of GNP during the synthesis process leads, mainly, to the enhanced growth of NiWO4 nanocrystallites, as well as induces changes in the surface chemistry. The elec-trochemical results show that the introduction of GNPs into the NiWO4 composite support leads to a significant improvement in the activity of the Pt electrocatalyst in ORR and HOR compared to both initial NiWO4 and Pt/NiWO4 samples, as well as mechanical mixtures of these catalysts with carbon. Mass activity for hydrogen oxidation, determined in a mixed kinetic-diffusion controlled region, obtained on the 8 wt.% Pt/NiWO4-GNP catalyst was significantly higher compared to the commercial 20 wt.% Pt/C Quintech catalyst. Our comprehensive structural and surface chemistry assessments indicate this composite material as a viable electrocatalyst for PEMFCs using a broader type of fuels.& COPY; 2022 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.

Light-emissive compounds able to transfer protons, either intra-or intermolecularly in the excited state, have increasingly attracted attention, especially by structural diversification of recognized fluorophores. We report herein synthesis and structural characterization of novel 1,3,4-oxadiazole-based compounds functionalised by salicylaldehyde or o-vanillin moieties. Solution absorption and emission spectroscopy performed on the resulted compounds indicated the essential influence of the established (intra and/or intermolecular) hydrogen bonds onto the optical properties. Theoretical calculations positively contributed to the effort of understanding the emissive behaviour of the compounds and the calculated data correlated very well to experiments. Occurrence of hydrogen bond interactions has been also observed in solid state and we discuss their molecular structures and the effects on the luminescent behaviour. The phenol groups in close proximity of the oxadiazole core were further exploited in cocrystallization experiments with pyridine-based co-partners. Hydrogen bonding were also found responsible for the supramolecular recognition between the two components. One type of the resulted co -crystals preserved the luminescence of the starting compound.