National Institute Of Materials Physics - Romania

The present study brings developments in the area of tissue engineering of heart valves, with the design and application of a new 2D model for human heart valve. This model contains valvular interstitial cells (VIC) encapsulated in gold covered electrospun polycaprolactone (PCL/Au) fibers, the latter serving also as an electrochemical sensor that enables the monitoring of oxygen levels of cellular media. The biocompatibility of PCL and PCL/Au with VIC was evaluated after the encapsulation of VIC in both scaffolds using the lactate dehydrogenase assay. Fluorescence microscopy of the encapsulated cells was used for the investigation of cell morphology, by employing phalloidin labelled F-actin (red) and DAPI nuclear staining (blue). The electrochemical techniques allowed to investigate the effect of cell encapsulation within the PCL/Au 2D constructs and to quantify the dissolved oxygen levels in cell culture media at both PCL/Au and PCL/Au with encapsulated cells (PCL/ Au/cells). Experiments were performed in a hypoxistation, which allowed a fine control on the cellular media oxygenation. Electrochemical impedance spectroscopy (EIS) was used to evaluate the electrochemical behavior of the 2D constructs, PCL/Au and PCL/Au/cells, in cellular media at different O-2 concentration. Results were analyzed and both impedance values at a fixed frequency and values of the equivalent circuit elements were used to construct calibration curves for dissolved O-2 determination. The second electrochemical technique used to monitor the levels of O-2 at PCL/Au and PCL/Au/cells in the cellular media was square wave voltammetry with sensitivities of 1.5 and 2.5 mu A cm(-2) mu M-1, for PCL/Au and PCL/Au/cells, respectively.

A nanostructured samarium oxide electrode was constructed by electrodeposition onto the surface of a gold electrode on SiO2/Si wafer. The samarium oxides electrode's surface morphology was investigated by scanning electron microcopy showing a quasi-monodispersed nanoplatelets like structure. X-rays diffraction analysis demonstrated a mixture of monoclinic and hexagonal phases while the X-rays photoelectron spectroscopy indicated the co-existence of both Sm2+ and Sm3+ species in a 1:3 proportion. Cyclic voltammetry and electrochemical impedance spectroscopy were used to investigate the charge transfer processes at the surface of the samarium oxide electrode in the absence and in the presence of redox probes. A roughness factor of 2.5 was determined from the samarium oxide electrode while the charge transfer constant was almost double when compared to the planar gold electrode. Then, the samarium oxide electrode was used for the H2O2 detection by fixed potential amperometry at -0.20 V (vs. Ag/AgCl) with a linear region between 0.01 and 1.00 mM, a sensitivity of 153 mu A cm(-2) mM(-1) and a LoD = 2.70 mu M. Glucose oxidase was used as a model enzyme in order to test the capacity of the samarium oxides electrode for biosensing. The enzyme was immobilized by physical adsorption and the optimum conditions for glucose analysis investigated. The biosensor showed a linear range for glucose detection between 0.10 and 1.20 mM with a sensitivity of 8.40 mu A cm(-2) mM(-1) and a LoD = 8.00 mu M. Selectivity was tested toward common interfering species, and the results revealed the lack of biosensor response. The glucose biosensor on samarium oxides was tested for glucose detection in serum samples with a recovery factor of 90%, and the result validated with a commercial glucometer. (C) 2021 Elsevier Ltd. All rights reserved.

The performances of 3.5 at.% Nd:LGSB bifunctional laser and nonlinear optical (NLO) crystal were investigated. A high-quality single crystal with incongruent melting, having dimensions of about 12 mm in diameter and 35 mm in length, was grown along the c-axis by the Czochralski technique. The phase-matching curve for type I second harmonic generation (SHG) was determined. Efficient laser emission at 1062 nm, along the phase-matching direction for SHG of 1062 nm radiation, was obtained under the pump at 807 nm with a fiber-coupled laser diode. The Nd:LGSB laser operated with a high slope efficiency of eta(sa) = 0.56 (with respect to the absorbed pump power), delivering the highest output power of 2.1 W for 4.04 W of absorbed pump power. Preliminary SFD experiments resulted in achieving a maximum green output power of 48 mW at 3.94 W absorbed pump power.

This work reports the effect of the rapid solidification technique and thermal treatment on the martensitic transformation (MT), magnetic and magnetostrictive properties on the off-stoichiometric Ni49Mn31Ga20 and Ni51Mn28Ga21 ferromagnetic shape memory ribbons. The samples were investigated by X-ray diffraction, differential scanning calorimetry, scanning electron microscopy, magnetic and magnetostrictive measurements. The temperature dependence of the X-ray phases analysis shows the presence of martensite structures, both tetragonal and monoclinic, at room temperature and allowed to study their evolution through MT. The thermal treatment induces changes in the microstructure with implications in MT and Curie temperatures evolution. The competition between the magnetization orientation and twin boundary motion within martensitic variants under magnetic field evidenced in the magnetic-strain curves was discussed and correlated with the magnetic data.

The local crystal/magnetic structures of the SrFe12-xInxO19 solid solutions (x = 0.1; 0.3; 0.6 and 1.2) were investigated using neutron powder diffraction. The measurements of the electric polarization for all investigated samples were carried out as a function of the external electric field. The presence of the ferroelectric and ferromagnetic ordering (dual ferroic ordering) in the SrFe12-xInxO19 hexaferrites at 300 K was found. This appearance contradicts to the conventional opinion describing their crystal structure (centrosymmetric space group P6(3)/mmc (No. 194)). The reason for the existence of a spontaneous polarization (nonzero dipole moment) in the SrFe12-xInxO19 hexaferrites continues controversial. The crystal structure of the hexaferrites was considered both the centrosymmetric P6(3)/mmc and non-centrosymmetric P6(3)mc space groups. This fact made it possible to find a connection between the emerging dipole moment and not equal distortions of the neighbor oxygen polyhedral. The nature description of the nonzero dipole moment formation in a quasi-centrosymmetrical system of the In-substituted SrFe12-xInxO19 hexaferrites was presented based on the neutron diffraction data. (C) 2021 Elsevier B.V. All rights reserved.

Piezoelectric hard/soft effects of multivalence co-dopants (Sb and Mn) in correlation with their location in the lattice, were investigated in PZT ceramics, prepared by conventional ceramic technology, with the following compositions: Pb0.98Sr0.02 ((Ti0.49Zr0.51)(1-0.015-x)Mn0.015Sbx)O-3 with x = 0, 0.005, 0.01, 0.02, 0.03, where antimony was initially assumed to substitute for Ti/Zr ions. The antimony valence state was found to be +3 in all samples by X-ray Photoelectron Spectroscopy investigations. The Electron Paramagnetic Resonance spectra evidenced a steep enhancement of the Mn2+ concentration upon increasing antimony doping level, explained by a charge compensation mechanism, between the Sb3+ ions substituting Pb2+ at the A-sites and the Mn2+ ions, localized at the B-sites. The incorporation of Sb3+ at the A-site of the PZT lattice is also supported by the variation of the lattice parameters, determined by X-ray Diffraction, with the increasing Sb concentration. The investigation of the dielectric, electromechanical and ferroelectric properties evidenced a hard piezoelectric behavior, mainly attributed to the presence of large sized Mn2+ ions, localized at B-sites. Our results prove that the piezoelectric hard/soft response is decisively influenced by the interplay between multiple valence states and locations of the co-dopants, on one hand, and the charge compensation mechanisms, on the other hand. This provides indirect information about the location of some co-dopants which can substitute for both cationic sites in the PZT based ceramics.

Samarium doped hydroxyapatite (Ca10-xSmx(PO4)(6)(OH)(2), x(Sm) = 0.5, 50SmHAp) is a very promising candidate to be used for different coatings in various dental and orthopedic implants. We report, for the first time, the obtaining of 50SmHAp thin films by a cost-effective method, namely spin coating. Thin films of 50SmHAp on silicon substrate have been analyzed by various techniques such as Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), atomic force microscopy (AFM), Metallographic microscopy and Glow Discharge Optical Emission Spectroscopy (GDOES). The stability of 50SmHAp suspension was evaluated by ultrasound measurements. Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM) and scanning electron microscopy (SEM) were also used to evaluate the 50SmHAp suspension. The antifungal activity of 50SmHAp suspension and coatings was assessed using Candida albicans ATCC 10231 fungal strain (C. albicans). The results of the antifungal assays depicted that both 50SmHAp suspensions and coatings were effective in inhibiting the development of C. albicans fungal cells, thus making them ideal candidates for the development of novel antifungal agents. The obtained results give new perspective for possible applications of 50SmHAp thin films in various medical applications due to their antifungal properties.

We investigated the optical and electrical properties of flexible single and bi-layer organic heterostructures prepared by vacuum evaporation with a p-type layer of arylenevinylene oligomers, based on carbazole, 3,3 ' bis(N hexylcarbazole)vinylbenzene = L13, or triphenylamine, 1,4 bis [4 (N,N' diphenylamino)phenylvinyl] benzene = L78, and an n-type layer of 5,10,15,20-tetra(4-pyrydil)21H,23H-porphyne = TPyP. Transparent conductor films of Al-doped ZnO (AZO) with high transparency, >90% for wavelengths > 400 nm, and low resistivity, between 6.9 x 10(-4) ohm center dot cm and 23 x 10(-4) ohm center dot cm, were deposited by pulsed laser deposition on flexible substrates of polyethylene terephthalate (PET). The properties of the heterostructures based on oligomers and zinc phthalocyanine (ZnPc) were compared, emphasizing the effect of the surface morphology. The measurements revealed a good absorption in the visible range of the PET/AZO/arylenevinylene oligomer/TPyP heterostructures and a typical injection contact behavior with linear (ZnPc, L78) or non-linear (L13) J-V characteristics in the dark, at voltages < 0.4 V. The heterostructure PET/AZO/L78/TPyP/Al showed a current density of ~1 mA/cm(2) at a voltage of 0.3 V. The correlation between the roughness exponent, evaluated from the height-height correlation function, grain shape, and electrical behavior was analyzed. Consequently, the oligomer based on triphenylamine could be a promising replacement of donor ZnPc in flexible electronic applications.

In this study, we develop chitosan-hydroxyapatite (CS-HAp) composite layers that were deposited on Si substrates in radio frequency (RF) magnetron sputtering discharge in argon gas. The composition and structure of CS-HAp composite layers were investigated by analytical techniques, such as Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), metallographic microscopy (MM), and atomic force microscopy (AFM). On the other hand, in the present study the second order derivative of FT-IR-ATR spectra, for compositional analyses of CS-HAp, were used. The SEM, MM, and AFM data have shown the formation of CS-HAp composite layers. The surface of CS-HAp composite layers showed uniform growth (at an Ar gas working pressure of p = 2 x 10(-3) mbar). The surface of the CS-HAp composites coatings became more nanostructured, becoming granular as the gas pressure increased from 5 x 10(-3) to 1.2 x 10(-2) mbar. However, our studies revealed that the surface morphology of the CS-HAp composite layers varies with the Ar gas working pressure. At the same time, optical properties are slightly influenced by Ar pressure. Their unique physicochemical properties make them suitable for various applications in the biomedical field, if we consider the already proven antimicrobial properties of chitosan. The antifungal properties and the capacity of the CS-HAp composite layers to inhibit the development of fungal biofilms were also demonstrated using the Candida albicans ATCC 10231 (C. albicans) fungal strain.

Hydroxyapatite (Ca-10(PO4)(6)(OH)(2), HAp), due to its high biocompatibility, is widely used as biomaterial. Doping with various ions of hydroxyapatite is performed to acquire properties as close as possible to the biological apatite present in bones and teeth. In this research the results of a study performed on thin films of hydroxyapatite co-doped with nitrogen and bromine (NBrHAp) are presented for the first time. The NBrHAp suspension was obtained by performing the adapted co-precipitation method using cetyltrimethylammonium bromide (CTAB). The thin layers of NBrHAp were obtained by spin-coating. The stability of the NBrHAp suspension was examined by ultrasound measurements. The thin layers obtained by the spin-coating method were examined by scanning electron microscopy (SEM), optical microscopy (OM), and metallographic microscopy (MM). The presence of nitrogen and bromine were highlighted by energy-dispersive X-ray spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) studies. Fourier transform infrared spectroscopy (FTIR) was used to highlight the chemical status of nitrogen and bromine. In addition, the powder obtained from the NBrHAp suspension was analyzed by XRD. Moreover, the in vitro antimicrobial activity of the NBrHAp suspensions and coatings was investigated using the reference microbial strains Staphylococcus aureus ATCC 25923, Escherichia coli ATCC 25922, and Candida albicans ATCC 10231. The results highlighted the successful obtainment of N and Br co-doped hydroxyapatite suspension for the first time by an adapted co-precipitation method. The obtained suspension was used to produce pure NBrHAp composite thin films with superior morphological properties. The NBrHAp suspensions and coatings exhibited in vitro antimicrobial activity against bacterial and fungal strains and revealed their good antimicrobial activity.