National Institute Of Materials Physics - Romania

The scope of this study consists of setting up of an integrated cost-effective sampling & laboratory analyses procedure which delineates sampling, sub-sampling and analytical uncertainties in case of fine-grained extractive waste deposits. This procedure is designed to support the decision makers towards fine-grained waste deposits upcycling and land reclamation. This procedure consists of a balanced replicated sampling design (BRSD) coupled with a three split levels ANOVA data processing. The paper provides the readership with the mathematical backgrounds of the three split level ANOVA analysis (3L-ANOVA) and an Excel algorithm for its implementation. Also, the paper presents an example of implementation of the developed methods in the case of a Romanian iron ore tailings (IOT) old pond. The findings of the paper consist of: a) argues, based on OM, SEM-EDS, XRFS and XRD observations, that classical TOS is ineffective for fine-grained waste deposits; b) BRSD in conjunction with 3L-ANOVA analysis is the only approach fit for reliable characterization of the fine-grained stockpiles; c) sampling uncertainty is the critical factor of the uncertainty budget of the analyte concentration; d) Lilliefors approach is adequate for the hypothesis testing where or not the measurand is normal distributed; e) The outcomes of the BRDSD&3L-ANOVA investigations carried on Teliuc tailings, estimated at circa 5.5* 106 m3, consist mainly of mineral quantification at lot level i.e. quartz-54% (+/- 7%), hematite-15% (+/- 3%), calcite-11% (+/- 3%), MgO 3% (+/- 1%), Al2O3 9% (+/- 2%). The concentrations of some CRMs like Ti, V, Ba, Y, W were found at ACE limits and their associated relative expanded uncertainties overpass 50%. Thus, the expanded uncertainties clearly depict the reliability of acquired data for the decision makers regarding waste valorization. f) The IOT into Teliuc can be upcycled as minerals for cement and ceramic industries as well as for geopolymer manufacture. Also, IOT can be downcycles as filler in road construction and mine closure. Finally, the Teliuc yard can be rehabilitated with zero-waste left behind. The data exactness provided by this procedure can be increased to any desirable level through increasing the number of collected items, but the cost of sampling and analyses increases proportionally. In such circumstances, the posted approach can be tailored at the stakeholder request as to safely underpin the decision to turn fine-grained by-products into valuable secondary resources, facilitating a greater circularity of the mining industry.

Replacing lead atoms in halide perovskite materials is of significant importance for the development of environmentally friendly perovskite solar cells. In this paper, we investigated the effect of doping the MAPbI(2.6)Cl(0.4) hybrid perovskite (MA-methyl ammonium) with non-toxic elements, such as alkaline earth metal ions (Mg2+) and transition metal ions (Zn2+). The structural, morphological, and optical properties of the prepared samples were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and UV-Vis. spectroscopy. Finally, the doped films were used as photoactive layers in solar devices in order to evaluate their photovoltaic performance. Zn proved to be more appropriate to replace partially Pb and films with higher quality were obtained. As a result, the MAPb1(-x)Zn(x)I(2.6)Cl(0.4) based solar cells have demonstrated a slight improvement of the photovoltaic performances, resulting in a uniform and narrower PCEs (power conversion efficiency) range, compared to pristine MAPbI(2.6)Cl(0.4) based devices.

Replacing lead atoms in halide perovskite materials is of significant importance for the development of environmentally friendly perovskite solar cells. In this paper, we investigated the effect of doping the MAPbI(2.6)Cl(0.4) hybrid perovskite (MA-methyl ammonium) with non-toxic elements, such as alkaline earth metal ions (Mg2+) and transition metal ions (Zn2+). The structural, morphological, and optical properties of the prepared samples were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and UV-Vis. spectroscopy. Finally, the doped films were used as photoactive layers in solar devices in order to evaluate their photovoltaic performance. Zn proved to be more appropriate to replace partially Pb and films with higher quality were obtained. As a result, the MAPb1(-x)Zn(x)I(2.6)Cl(0.4) based solar cells have demonstrated a slight improvement of the photovoltaic performances, resulting in a uniform and narrower PCEs (power conversion efficiency) range, compared to pristine MAPbI(2.6)Cl(0.4) based devices.

Novel biomaterials with promising bone regeneration potential, derived from rich, renewable, and cheap sources, are reported. Thus, thin films were synthesized from marine-derived (i.e., from fish bones and seashells) hydroxyapatite (MdHA) by pulsed laser deposition (PLD) technique. Besides the physical-chemical and mechanical investigations, the deposited thin films were also evaluated in vitro using dedicated cytocompatibility and antimicrobial assays. The morphological examination of MdHA films revealed the fabrication of rough surfaces, which were shown to favor good cell adhesion, and furthermore could foster the in-situ anchorage of implants. The strong hydrophilic behavior of the thin films was evidenced by contact angle (CA) measurements, with values in the range of 15-18 degrees. The inferred bonding strength adherence values were superior (i.e., similar to 49 MPa) to the threshold established by ISO regulation for high-load implant coatings. After immersion in biological fluids, the growth of an apatite-based layer was noted, which indicated the good mineralization capacity of the MdHA films. All PLD films exhibited low cytotoxicity on osteoblast, fibroblast, and epithelial cells. Moreover, a persistent protective effect against bacterial and fungal colonization (i.e., 1- to 3-log reduction of E. coli, E. faecalis, and C. albicans growth) was demonstrated after 48 h of incubation, with respect to the Ti control. The good cytocompatibility and effective antimicrobial activity, along with the reduced fabrication costs from sustainable sources (available in large quantities), should, therefore, recommend the MdHA materials proposed herein as innovative and viable solutions for the development of novel coatings for metallic dental implants.

Sodium hexatitanate (Na2Ti6O13) nanoparticles have been synthesized by the hydrothermal method with microwave and conven-tional heating, after which their photocatalytic properties toward an azo dye pollutant degradation have been investigated. Insights into the dynamics and reactivity of the species involved in the photocatalytic mechanism of the (Na2Ti6O13) samples were precisely investigated, for the first time, by X-band electron paramagnetic resonance (EPR) spectroscopy under different experimental conditions. X-ray diffraction structural analysis revealed that all samples crystallized in a monoclinic C2/m structure, with different short-range structural order according to the employed heating, as indicated by Raman. Field-emission scanning electron microscopy and transmission electron microscopy results revealed the formation of rod-and fiber-like nanoparticles with different diameters and lengths. EPR measurements indicated the presence of different Ti3+ point defects and F centers in the samples. X-ray photoelectron spectroscopy analysis proved the presence of oxygen-related defects, but no Ti3+ was detected on the surface. Spin trapping experiments monitored the generation of hydroxyl (OH center dot) radicals over UV-irradiation time. Various parameters contribute to the photocatalytic activity of the samples; however, the type of defect and particle morphology appeared as key factors for enhanced efficiency. Our study provides significant information about paramagnetic defects in Na2Ti6O13 materials and their role in photocatalysis to design other Ti-based photocatalysts.

The development of new thin-film cathodes triggered a recent research interest in energy storage applications. Over the past years, vanadium oxides have been extensively explored as promising electrodes for batteries owing to their rich valence states and remarkable electrochemical properties. Herein, we report on the synthe-sis of undoped and Sn doped V2O3 thin-films on graphene (G)/Al foil by pulsed laser deposition followed by rapid thermal annealing in N2 at low temperature (similar to 430 degrees C). The obtaining V2O3 phase on graphene/Al foil (G/Al) has been confirmed by X-ray diffraction and Raman and X-ray photoelectron spectroscopy analyses. The synthesized vanadium oxide films were tested as cathodes in coin cells. The electrochemical properties have been systematically investigated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and galvanostatic charge discharge (GCD) measurements. A superior electrochemical performance was observed for the V2O3 on G/Al structures, with an initial capacity of around 300 mAh g-1, with respect to the bare G/Al electrode. The use of the Sn-doped (5 mol%) V2O3 thin-films improved slightly the initial capac-ity up to a value of ca. 311 mAh g-1. Both V2O3/G/Al and Sn-doped V2O3/G/Al exhibited excellent cycling performances after 40 cycles with a capacity maintenance at a C-rate C/20 of 317 mAh g-1. Long-term cycling test (up to 200 cycles) showed that the Sn doping could be an excellent strategy to improve the stability of the electrodes, which yielded a capacity loss of only 0.128% per cycle. Possible mechanisms are presented and dis-cussed. This work could serve as point of reference for future developments in the field of batteries employing vanadium oxide-based thin-films deposited by physical vapor deposition techniques.

Cu2NiSnS4 (CNTS) absorber layers are elaborated by electrodeposition at various applied potentials followed by sulfurization treatment at 450 degrees C under sulfur atmosphere. The microstructural investigations revealed the presence of Cu4SnS4 secondary phases which can be reduced using an applied potential of -1.15 V vs. Ag/AgCl. Using the corresponding cathodic potential for Ni2+, the competing detrimental hydrogen evolution regresses the morphology and composition. The film with the highest Ni concentration has a band gap of 1.44 eV as inferred from diffuse reflectance data. The Randles cell model is probed by electrochemical impedance spectroscopy.

Whereas solar photovoltaic cells are promising for proper power production, their wide deployment is hampered by production costs, material availability and toxicity. One of these materials is CuO, which has great chemical stability as well as interesting physical properties, including a direct band gap, a high absorption coefficient, and p-type conductivity. These properties indicate CuO as an exciting semiconducting material to use an absorber layer in thin films solar cells. For this specific reason, this paper focuses on the synthesis of pristine and Ni-incorporated CuO thin films by spray pyrolysis process. Several techniques such as; X-ray diffraction (XRD), Raman spectroscopy, Scanning Electron Microscopy (SEM), Energy dispersive X-ray (EDX) and UV-Visible spectroscopy have been employed to characterize the synthesized samples. The XRD analysis indicated the formation of polycrystalline CuO thin films and the average crystallite size was decreased from 35 to 20 nm for the samples with x = 0-8 at%, respectively. Furthermore, Raman spectroscopy also confirms the single-phase formation of CuO films. The SEM images demonstrated that the incorporation of Ni in the CuO matrix improved the films surface. The EDX analysis and the elemental mapping belay the homogeneous distribution of the elements. Moreover, UV-Visible spectroscopy has shown a significant expansion in optical energy band gap from 1.45 to 1.53 eV with an increase of Ni concentration. On the other hand, to investigate the impact of Ni-incorporated CuO on nanostructure Ni:CuO/ZnO-NRs heterojunction solar cell performance, SCAPS-1D software is used. It has been found that, 8% Ni:CuO layer has been revealed as better for nanostructured solar cells. The results of this contribution will provide some vital guidelines for fabricating higher-efficiency solar cells.

High-energy physics detectors with internal charge multiplication, like Low Gain Avalanche Detectors (LGADs), that will be used for fast timing in the High Luminosity LHC experiments, have to exhibit a significant radiation tolerance. In this context, the impact of radiation on the highly boron-doped gain layer is of particular interest, since due to the so-called Acceptor Removal Effect (ARE) a radiation-induced deactivation of active boron dopants takes place, that is causing a progressive loss in the gain with increasing irradiation level. In this paper we present defect-spectroscopy measurements (Deep-Level Transient Spectroscopy and Thermally Stimulated Current technique) on neutron, proton and electron irradiated p-type silicon pad diodes of different resistivity as well as LGADs neutron irradiated at fluences up to 1 x 1015 neq/cm2. We show that compared to silicon pad diodes the determination of LGAD defect introduction rates is less straightforward as they are strongly influenced by the impact of the gain layer. The measured gain layer capacitance has a strong frequency and temperature dependence which makes DLTS measurements challenging to perform with results difficult to interpret. With the TSC technique the defects formed in the LGADs are nicely observed and can be compared to the defects formed in the silicon pad diodes. However, the exact assignment of defects to the gain layer or bulk region remains challenging and the charge amplification effect of the LGADs impacts the exact determination of defect concentrations. We also demonstrate that, depending on the TSC measurement conditions, defect induced internal electric fields are built up in the irradiated LGADs which impact the signal current.

The technology of perovskite solar cells (PSC) is getting close to breaching the consumer market. Yet, one of the current challenges is to reduce the toxicity during their fabrication by reducing the use of the toxic solvents involved in the perovskite fabrication process. A good solubilization of lead halides used in hybrid perovskite preparation is required, and it is only possible with polar solvents. A mixture of dimethylformamide (DMF) and dimethyl sulfoxide (DMSO) is the most popular solvent combination for a perovskite precursor solution. DMF is necessary to ensure a good dissolution of lead iodide, but it is also the most toxic solvent. In this paper, we study the replacement of the dimethylformamide with presumably less toxic alternatives, such as N-methyl-2-Pyrrolidone (NMP) and ethyl acetate (EA), for the preparation of the K(0.1)FA(0.7)MA(0.2)PbI(2.8)Cl(0.2) (KFAMA) hybrid perovskite. The perovskite thin films were investigated by various characterization techniques: X-ray diffraction, atomic force microscopy, scanning electron microscopy, and UV-vis spectroscopy, while the photovoltaic parameters were determined by measuring the IV curves of the corresponding solar cells. The present study shows that by keeping the same deposition parameters as when only DMF solvent is used, the partial solvent substitution with NMP and EA gives promising results for reducing the toxicity of the fabrication process of KFAMA-based PSCs. Thus, with no specific optimization of the deposition process, and for the maximum possible partial substitution of DMF with NMP and EA solvents, the loss in the power conversion efficiency (PCE) value is only 35% and 18%, respectively, associated with the more structural defects promoted by NMP and EA.