National Institute Of Materials Physics - Romania

Almost all proposed configurations and practical achievements based on superconductor/ferromagnet (S/F) heterostrucutres focus on s-wave superconductors. However, several attempts targeted also high temperature superconductors, most of them using manganite ferromagnets LaXMnO3 (X: Ca or Sr) and Y1Ba2Cu3O7-x (YBCO). Here we propose a new ferromagnetic material that can be used with YBCO for the fabrication of S/F hybrid structures. We show that a ferromagnetic order can be induced in a thin layer (similar to 130 nm thickness) of CaRuO3 grown by pulsed laser deposition on epitaxial YBCO film. Detailed magnetic and structural investigations show that the observations of the weak ferromagnetism are consistent with the magnetic order induced by in-plane tensile strain of about 1.7% and the easy-magnetization axis forms an angle of similar to 180o with the layer plane. The value of the Curie temperature T (Curie) estimated using the Curie-Weiss law was 340 K. An unusual temperature dependence of the magnetic moment around the superconducting transition was observed in both field-cooled and zero-field-cooled configurations which is attributed to the paramagnetic Meissner effect.

Cu-Fe-Sn-S have been electrodeposited on indium tin oxide coated glass (ITO/glass) substrates, varying only the deposition time, followed by sulfurization in argon atmosphere at a temperature of 500 degrees C. X-ray diffraction patterns confirmed the formation of polycrystalline CFTS and other secondary phases. The Raman spectroscopy results confirm the formation of stannite phase, by the existence of the most intense peak at 330 cm(-1) corresponding to A-symmetry vibrational mode, while the SnS2 surface phase reduces upon increasing deposition time. The inferred bandgaps by specular transmission are in 1.4-1.7 eV range, influenced by the detected orthorhombic Cu4SnS4 and rhodostannite secondary phases. The electrical measurements confirm the p-type nature of the films, while density of free carriers is relatively high (similar to 10(19) cm(-3)), leading to extremely low resistivity in the Omega cm range.

The discovery of multifunctional properties related to electro-activity of organic systems of biomolecules is important for a variety of applications, especially for devices in the realm of biocompatible sensors and/or bioactuators. A further step towards such applications is to prepare thin films with the required properties. Here, the investigation is focused on the characterization of films of guanine and cytosine nucleobases, prepared by thermal evaporation-an industrial accessible deposition technique. The cytosine films have an orthorhombic non-centrosymmetric structure and grow in two interconnected nanostructured fractal patterns, of nearly equal proportion. Piezoresponse force microscopy images acquired at room temperature on the cytosine films display large zones with antiparallel alignment of the vertical components of the polarization vector. Guanine films have a dense nano-grained morphology. Our studies reveal electrical polarization switching effects which can be related to ferroelectricity in the films of guanine molecules. Characteristic ferroelectric polarization-electric-field hysteresis loops showing large electrical polarization are observed at low temperatures up to 200 K. Above this temperature, the guanine films have a preponderant paraelectric phase containing residual or locally induced nano-scopic ferroelectric domains, as observed by piezoresponse force microscopy at room temperature.

Rare-earth elements are widely used as doping materials as they considerably change the semiconductor optical, electrical, magnetic and radiative properties. This work explores the influence of Gadolinium (Gd) as a dopant on the radiative, optical and magnetic properties of the Zinc Selenide (ZnSe). ZnSe single crystals were grown by the physical transport method and doped during the growth process using a GdSe source. A wide range of characterization equipment was employed to analyze the obtained ZnSe:Gd single crystals. Intracenter radiative transition of the Gd has not been detected. Gd ions activate the background impurities, causing radiative transitions from the conduction band to the Cu2+ level and intracenter transitions within V3+, V2+ and Cr2+ ions. At the same time, the edge band intensity is dependent on the dopant concentration. Optical transmittance decreases, but the position of the fundamental absorption band is unchanged. Single crystals have a zinc blende crystal structure, and Gd ions do not form complexes with native defects or background impurities.

Pristine high-density bulk disks of MgB2 with added hexagonal BN (10 wt.%) were prepared using spark plasma sintering. The BN-added samples are machinable by chipping them into desired geometries. Complex shapes of different sizes can also be obtained by the 3D printing of polylactic acid filaments embedded with MgB2 powder particles (10 wt.%). Our present work aims to assess antimicrobial activity quantified as viable cells (CFU/mL) vs. time of sintered and 3D-printed materials. In vitro antimicrobial tests were performed against the bacterial strains Escherichia coli ATCC 25922, Pseudomonas aeruginosa ATCC 27853, Staphylococcus aureus ATCC 25923, Enterococcus faecium DSM 13590, and Enterococcus faecalis ATCC 29212; and the yeast strain Candida parapsilosis ATCC 22019. The antimicrobial effects were found to depend on the tested samples and microbes, with E. faecium being the most resistant and E. coli the most susceptible.

Glasses from lithium-aluminum-zinc-boron-phosphorous oxide system co-doped with terbium (Tb3+) and dysprosium (Dy3+) oxides were studied for magneto-optical applications in lasers. The Fourier Transform Infrared and Raman Spectroscopy complementary analysis suggested the depolymerization of the borophosphate glass network by adding and increasing the rare-earth (RE) oxide content. Main UV-vis absorption maxima of Tb and Dy ions were identified at 348 and 1266 nm. Spectroscopic ellipsometry indicated a maximum refractive index of 1.56, at 400 nm, for the highest RE content. The Verdet constant amplified by increasing the RE content, reaching for the 9 mol% RE co-doped sample a value of -0.075 min/Oe/cm at 630 nm. The Faraday rotation angle was additionally confirmed by using a Faraday Cell Device, being also related to the specific paramagnetic behavior evidenced by Superconducting Quantum Interference Device magnetometry. The magneto-optical properties recommend such vitreous co-doped materials for magneto-optical devices.

The feasibility of mixed-cation mixed-halogen perovskites of formula A(x)A'1-xPbXyXz'X3-y-z '' is analyzed from the perspective of structural stability, opto-electronic properties and possible degradation mechanisms. Using density functional theory (DFT) calculations aided by machine-learning (ML) methods, the structurally stable compositions are further evaluated for the highest absorption and optimal stability. Here, the role of the halogen mixtures is demonstrated in tuning the contrasting trends of optical absorption and stability. Similarly, binary organic cation mixtures are found to significantly influence the degradation, while they have a lesser, but still visible effect on the opto-electronic properties. The combined framework of high-throughput calculations and ML techniques such as the linear regression methods, random forests and artificial neural networks offers the necessary grounds for an efficient exploration of multi-dimensional compositional spaces.

ZnS is a wide band gap material which was proposed as a possible candidate to replace CdS as a buffer layer in solar cells. However, the structural and optical properties are influenced by the deposition method. ZnS thin films were prepared using magnetron sputtering (MS), pulsed laser deposition (PLD), and a combined deposition technique that uses the same bulk target for sputtering and PLD at the same time, named MSPLD. The compositional, structural, and optical properties of the as-deposited and annealed films were inferred from Rutherford backscattering spectrometry, X-ray diffraction, X-ray reflectometry, Raman spectroscopy, and spectroscopic ellipsometry. PLD leads to the best stoichiometric transfer from target to substrate, MS makes fully amorphous films, whereas MSPLD facilitates obtaining the densest films. The study reveals that the band gap is only slightly influenced by the deposition method, or by annealing, which is encouraging for photovoltaic applications. However, sulphur vacancies contribute to lowering the bandgap and therefore should be controlled. Moreover, the results add valuable information towards the understanding of ZnS polymorphism. The combined MSPLD method offers several advantages such as an increased deposition rate and the possibility to tune the optical properties of the obtained thin films.

High-quality ZnS thin films as buffer layer have been successfully synthesized and simulated using the low-cost Mist CVD technique and the SCAPS-1D software for different deposition times (30, 40, 50, and 60 min). The structural, morphological, and optical properties of the prepared ZnS films have been investigated using X-ray diffraction (XRD), scanning electronic microscopy (SEM), atomic force microscopy (AFM), and UV-Vis spectrophotometer. The time deposition effect on ZnS films' efficiency as a buffer layer has been evaluated. XRD pattern confirms the hexagonal/cubic structure of the prepared samples, with (111) as preferred orientation. Raman spectra confirm XRD findings by the two peaks located at 348 cm(-1) and 697 cm(-1) which correspond to ZnS samples' cubic and hexagonal structures. Scanning electronic microscopy (SEM) and atomic force microscopy (AFM) images show densely uniform grains with precise shapes and boundaries covering the entire sample's surface with a relative roughness for all deposition times. The optical transmittance shows an average of 78% in the visual field of light with an optical band gap varying between 3.69 and 3.80 eV. Numerical simulation of ZnO:Al/ZnS/CZTS/Mo cell using SCAPS-1D software shows that the sample deposited for 30 min presents the best performance with an efficiency of up to 8.9%.

Cu2ZnSnS4 (CZTS) is a complex quaternary material, and obtaining a single-phase CZTS with no secondary phases is known to be challenging and dependent on the production technique. This work involves the synthesis and characterization of CZTS absorber layers for solar cells. Thin films were deposited on Si and glass substrates by a combined magnetron sputtering (MS) and pulsed laser deposition (PLD) hybrid system, followed by annealing without and with sulfur powder at 500 degrees C under argon (Ar) flow. Three different Cu2S, SnS2, and ZnS targets were used each time, employing a different target for PLD and the two others for MS. The effect of the different target arrangements and the role of annealing and/or sulfurization treatment were investigated. The characterization of the absorber films was performed by grazing incidence X-ray diffraction (GIXRD), X-ray reflectometry (XRR), Raman spectroscopy, scanning electron microscopy, and regular transmission spectroscopy. The film with ZnS deposited by PLD and SnS2 and Cu2S by MS was found to be the best for obtaining a single CZTS phase, with uniform surface morphology, a nearly stoichiometric composition, and an optimal band gap of 1.40 eV. These results show that a new method that combines the advantages of both MS and PLD techniques was successfully used to obtain single-phase Cu2ZnSnS4 films for solar cell applications.