National Institute Of Materials Physics - Romania

A complex investigation of the morpho-structural, magnetic, magneto-optical and magneto-transport properties of amorphous Fe-Gd thin films crossing the magnetization compensation point is reported and the unexpected observed magneto-functionalities are discussed. A tendency of magnetic domain formation with increasing the Fe content over the compensation concentration is observed. The switch from a reversed Magneto-optical Kerr Effect loop to a direct loop when increasing the Fe content over the compensation point is explained via the specific contribution to the rotation of the polarization vector from each magnetic sublattice, belonging to Fe and Gd, respectively. Local atomic configurations and magnetic interactions ascertained the amorphous character and revealed an out-ofplane orientation of the magnetic moment of Fe above the compensation point. The thermomagnetic curves prove a concentration dependent behavior, explained by weakly coupled magnetization relaxation processes of the two magnetic sub-lattices. On the other hand, the magnetic hysteresis loops gave evidence of two exchange coupled magnetic phases with different coercive fields. According to structural and Fe-57 Mossbauer Spectroscopy results, the two phases correspond to definite nanosized volumes of two different average concentrations (one of them closer to the compensation point) which are randomly distributed in the film. The unexpected single step-like behavior of the magneto-resistivity curves was explained by dissimilar switching of the spins in these two magnetic phases distributed in nano-sized volumes.

We explore the cross coupling between the ferroelectric and ferromagnetic phases in Ni/BaTiO3(001) heterostructures and demonstrate the modulation of the magnetism and incidence of exchange bias in the ultrathin metallic Ni overlayer, depending on the ferroelectric state of the bottom layer. We establish that 5-nm-thick monocrystalline Ni film deposited on BaTiO3 with ferroelectric polarization pointing towards the surface (P+) favors the organization of Ni into uniform ferromagnetic domains. Ni grown on BaTiO3 with opposite ferroelectric polarization is featured by emerging exchange-bias coupling between the ferromagnetic Ni top layers and the antiferromagnetic reacted interface, as theoretically explained by first-principles calculations. We explicitly obtain the morphology of the magnetic domains of the crystalline Ni layer in atomic and magnetic force microscopy measurements (AFM/MFM). The resemblance of AFM and MFM images indicate that, although with radically different morphologies, in both cases all spins orient in the Ni plane. Consequently, the distinct signature of the ferroelectric-ferromagnetic coupling extracted from the magneto-optical Kerr effect measurements encodes all the information of sample magnetism. The peculiar magnetic coupling depending on the ferroelectric state indicates new ways of engineering the functionality of metal/ferroelectric interfaces.

A facile and cheap surfactant-assisted hydrothermal method was used to prepare mesoporous cobalt ferrite nanosystems with BET surface area up to 151 m(2)/g. These mesostructures with high BET surface areas and pore sizes are made from assemblies of nanoparticles (NPs) with average sizes between 7.8 and 9.6 nm depending on the initial pH conditions. The pH proved to be the key factor for controlling not only NP size, but also the phase purity and the porosity properties of the mesostructures. At pH values lower than 7, a parasite hematite phase begins to form. The sample obtained at pH = 7.3 has magnetization at saturation M-s = 38 emu/g at 300 K (54.3 emu/g at 10 K) and BET surface area S-BET = 151 m(2)/g, whereas the one obtained at pH = 8.3 has M-s = 68 emu/g at 300 K (83.6 emu/g at 10 K) and S-BET = 101 m(2)/g. The magnetic coercive field values at 10 K are high at up to 12,780 Oe, with a maximum coercive field reached for the sample obtained at pH = 8.3. Decreased magnetic performances are obtained at pH values higher than 9. The iron occupancies of the tetrahedral and octahedral sites belonging to the cobalt ferrite spinel structure were extracted through decomposition of the Mossbauer patterns in spectral components. The magnetic anisotropy constants of the investigated NPs were estimated from the temperature dependence of the hyperfine magnetic field. Taking into consideration the high values of BET surface area and the magnetic anisotropy constants as well as the significant magnetizations for saturation at ambient temperature, and the fact that all parameters can be adjusted through the initial pH conditions, these materials are very promising as recyclable anti-polluting agents, magnetically separable catalysts, and targeted drug delivery vehicles.

Matrix-assisted pulsed laser evaporation (MAPLE) was used to deposit hybrid nanocomposite thin films based on cobalt phthalocyanine (CoPc), C60 fullerene and ZnO nanoparticles. The inorganic nanoparticles, with a size of about 20 nm, having the structural and optical properties characteristic of ZnO, were chemically synthesized by a simple precipitation method. Furthermore, ZnO nanoparticles were dispersed in a dimethyl sulfoxide solution in which CoPc and C60 had been dissolved, ready for the freezing MAPLE target. The effect of the concentration of ZnO nanoparticles on the structural, morphological, optical and electrical properties of the CoPc:C60:ZnO hybrid nanocomposite layers deposited by MAPLE was evaluated. The infrared spectra of the hybrid nanocomposite films confirm that the CoPc and C60 preserve their chemical structure during the laser deposition process. The CoPc optical signature is recognized in the ultraviolet-visible (UV-Vis) spectra of the obtained layers, these being dominated by the absorption bands associated to this organic compound while the ZnO optical fingerprint is identified in the photoluminescence spectra of the prepared layers, these disclosing the emission bands linked to this inorganic semiconductor. The hybrid nanocomposite layers exhibit globular morphology, which is typical for the thin films deposited by MAPLE. Current-voltage (J-V) characteristics of the structures developed on CoPc:C60:ZnO layers reveal that the addition of an appropriate amount of ZnO nanoparticles in the CoPc:C60 mixture leads to a more efficient charge transfer between the organic and inorganic components. Due to their photovoltaic effect, structures featuring such hybrid nanocomposite thin films deposited by MAPLE can have potential applications in the field of photovoltaic devices.

We propose a concept of hybrid nanoelectronic-magnetic device made of magnetic Fe-C core-shell nanoparticles deposited onto prepatterned Si (111) substrate with basic circuitry made of metallic conductive lines. The synthesis of magnetic material and the creation of nanoelectronic prepatterned interdigitated die are reported and to prove the effectiveness in devices, their magnetotransport properties are investigated. Magnetic Fe/FeC nanoparticles, 11 nm diameter, with a core-shell structure have been prepared by laser pyrolysis. Two different layouts of prepatterned interdigitated die, have been conceived using e-beam lithography, with various geometries. A range of microscopy techniques, transmission electron, scanning and optical, were employed for morphological characterization of the as-obtained structures. Magnetic and magnetotransport characterization using SQUID magnetometry has been performed onto both the core-shell nanoparticles and onto the hybrid device obtained by depositing centrifugated and dispersed core-shell nanoparticles from liquid carrier solutions. From magnetotransport measurements, it has been revealed that the hybrid device made of Fe/FeC nanosized materials on prepatterned interdigitated die exhibit a large giant magnetoresistive (GMR) effect of about 8% at 300 K. This result is promising in view of the use of such devices as arrays of nanosensors and in spintronic applications.

Nanocomposites of polyvinylidene fluoride loaded with various amounts of gamma-Fe2O nanoparticles, with an average size ranging between 20 and 40 nm, have been obtained by melt mixing and investigated using various experimental techniques [Superconducting Quantum Interference Device, Mossbauer, and Thermogravimetric Analysis]. Magnetic and Mossbauer measurements confirmed the presence of maghemite and a trace of a paramagnetic iron compound. Magnetic data are consistent with a blocking temperature close to room temperature (RT), showing a decrease in the coercive field as the temperature is increased. A weak exchange bias was noticed in all nanocomposites investigated at all temperatures and tentatively ascribed to surface spin disorder. The temperature dependence of the coercive field obeys the Kneller law. The nanocomposites exhibit superparamagnetic behavior near RT. Most magnetic measurements have been performed below the blocking temperature, revealing thus a complex behavior. The dependence of the mass loss derivative versus temperature, as obtained by thermogravimetric analysis, exhibits a single peak due to the thermal degradation of the polymeric matrix. A weak increase in the thermal stability of the polymeric matrix upon loading with maghemite is reported.

The particle reinforcement of fusion-relevant tungsten through the incorporation of tungsten sub-carbide W2C particles at the grain boundaries is demonstrated as an effective way of eliminating the harmful W oxide, enhancing densification and stabilising the composite's microstructure and flexural strength at room and high temperatures. The W2C particles are formed in situ during the sintering by carbon diffusion from WC nano-particles added as a precursor to the W matrix. Even in an extremely fast sintering process using Field-Assisted Sintering Technology (FAST, 1900 degrees C, 5 min), the added WC completely transforms to W2C, resulting in a W-W2C composite. While at least 5 vol % of WC nanoparticles are needed to eliminate the oxide, approximately 10 vol % result in a W-W2C composite with favourable characteristics: high density, high flexural strength at RT (>1200 MPa) as well as at elevated temperatures, and high thermal conductivity, which remains above 100 W/mK up to 1000 degrees C.

Magnetic Fe@Y composites (carbon-coated magnetic iron nanoparticles incorporated in zeolite Y) with 5-8 wt % Fe were synthesized and characterized. Overall acidity of the samples ranged between 2.0 and 2.47 mmol/g and is mostly attributed to Lewis acid sites. The obtained materials were proven to catalyze the hydrolysis of the marine sulfated polysaccharide ulvan with high conversion rates. The distribution of the reaction products depended on the reaction conditions and the concentration of ulvan. The catalytic property catalytic performance correlations clearly showed that the acid zeolite Y is the active phase for the hydrolysis of ulvan, while the iron nanoparticles enable the catalyst separation in a magnetic field. Under oxygen pressure, the selectivity was completely changed to favor succinic acid production. All Fe@Y composites were recycled 10 times with no change in their catalytic performance after recovery via a simple magnetic separation and washing with water.

Magnetic iron oxides have been used in biomedical applications, such as contrast agents for magnetic resonance imaging, carriers for controlled drug delivery and immunoassays, or magnetic hyperthermia for the past 40 years. Our aim is to investigate the effect of pressure and temperature on the structural, thermal, and magnetic properties of iron oxides prepared by hydrothermal synthesis at temperatures of 100-200 degrees C and pressures of 20-1000 bar. It has been found that pressure influences the type of iron oxide crystalline phase. Thus, the results obtained by Mossbauer characterization are in excellent agreement with X-ray diffraction and optical microscopy characterization, showing that, for lower pressure values (<100 bar), hematite is formed, while, at pressures >100 bar, the major crystalline phase is goethite. In addition, thermal analysis results are consistent with particle size analysis by X-ray diffraction, confirming the crystallization of the synthesized iron oxides. One order of magnitude higher magnetization has been obtained for sample synthesized at 1000 bar. The same sample provides after annealing treatment, the highest amount of good quality magnetite leading to a magnetization at saturation of 30 emu/g and a coercive field of 1000 Oe at 10 K and 450 Oe at 300 K, convenient for various applications.

A study on clay mineral polymer nanocomposites (CPN), namely polyaniline/montmorillonite-cetyltrimethylammonium bromide (PANI/Mt-CTAB), poly o-anisidine/montmorillonite-cetyltrimethylammonium bromide (poly(o-ANIS)/Mt-CTAB) and poly o-anisidine-co-aniline/montmorillonite-cetyltrimethylammonium bromide (poly(o-ANIS-co-ANI)/Mt-CTAB), synthesized by oxidative chemical polymerization method is presented. The nanocomposites have been characterized by Fourier transform infrared spectroscopy, UV-vis spectroscopy, and cyclic voltammetry, X-ray diffraction, scanning electron microscopy, transmission electron microscopy, cyclic voltammetry and thermogravimetry and differential scanning calorimetry analysis. By UV-vis measurements different electronic transitions for the CPNs were pointed out. The voltammograms indicate that the synthetized materials are electroactive. The FTIR analysis reveals the characteristic bands of the polymers and of the Mt-CTAB. The shift of the bands to higher/lower wavenumbers demonstrate the interaction between the pristine polymers macromolecular chains and the montmorillonite (Mt). The intercalation of the polymers inside the mineral clay was confirmed by the increased interlayer distance connected with the position of the 011 diffraction plane of the Mt., and the intercalation and exfoliation states were highlighted in the scanning and transmission electron microscopy images. The obtained results are encouraging in respect with the purpose to use them in the field of photovoltaic applications.