National Institute Of Materials Physics - Romania

A series of five Cu(x)CeMgAlO mixed oxides with different copper contents (x) ranging from 6 to 18 at. % with respect to cations, but with fixed 10 at. % Ce and Mg/Al atomic ratio of 3, were prepared by thermal decomposition of layered double hydroxide (LDH) precursors at 750 degrees C. The solid containing 15 at. % Cu, i.e. Cu (15)CeMgAlO, was also calcined at 550 and 650 degrees C. Powder XRD was used to characterize the crystalline structure and SEM-EDX was used to monitor the morphology and chemical composition of both as prepared and calcined materials. Additionally, the textural properties and the reducibility of the mixed oxide catalysts were studied by nitrogen adsorption/desorption and temperature programmed reduction with hydrogen (H-2-TPR) techniques, respectively. X-ray photoelectron spectroscopy (XPS) was used to determine the chemical state of the elements on the catalyst surface and the diffuse reflectance UV-vis spectroscopy, to obtain information about the stereochemistry and aggregation of copper in the Cu-containing mixed oxides. Their catalytic properties in the total oxidation of methane, used as a volatile organic compound (VOC) model molecule, were evaluated and compared with those of an industrial Pd/Al2O3 catalyst. Their catalytic behavior was explained in correlation with their physicochemical properties. Cu(15)CeMgAlO mixed oxide was shown to be the most active catalyst in this series, with a T-50 (temperature corresponding to 50% methane conversion) value of only ca. 45 degrees C higher than that of a commercial Pd/Al2O3 catalyst. This difference becomes as low as ca. 25 degrees C for the Cu(15)CeMgAlO system calcined at 550 degrees C. The influences of the contact time and of the methane concentration in the feed gas on the catalytic performances of the Cu(15)CeMgAlO catalyst have been investigated and its good stability on stream was evidenced.

Mixtures of nitrogen-doped titanium dioxide (TiO2:N) with different concentrations of Ag and/or SiO2 particles (0.5, 1 and 2 wt.%) were prepared in solid state by mechanico-chemical interactions. Using UV-VIS spectroscopy, Raman scattering, photoluminescence (PL) and photoluminescence excitation (PLE), the influence of the particles on the host material is evaluated. UV-VIS spectroscopy studies indicate a TiO2:N band gap shift to the UV range with increasing concentrations of SiO2 and Ag particles. PL intensities decrease with increasing concentrations of Ag and/or SiO2 particles in the TiO2:N host matrix, which in turn could effectively restrict the electron and hole recombination. To explain these processes, the different de-excitation ways will be advanced, taking into account the energy levels diagram of TiO2:N/Ag, TiO2:N/SiO2 and TiO2:N/Ag/SiO2 systems. PLE spectra show a gradual decrease in their relative intensities after 165 min of continuous irradiation due to photosensitivity of TiO2:N. The plasmonic effect of Ag particles in the TiO2:N/Ag system is highlighted for the first time by PLE studies.

Control of structural coupling at complex-oxide interfaces is a powerful platform for creating ultrathin layers with electronic and magnetic properties unattainable in the bulk. However, with the capability to design and control the electronic structure of such buried layers and interfaces at a unit-cell level, a new challenge emerges to be able to probe these engineered emergent phenomena with depth-dependent atomic resolution as well as element- and orbital selectivity. Here, we utilize a combination of core-level and valence-band soft x-ray standing-wave photoemission spectroscopy, in conjunction with scanning transmission electron microscopy, to probe the depth-dependent and single-unit-cell resolved electronic structure of an isovalent manganite superlattice [Eu0.7Sr0.3MnO3/La0.7Sr0.3MnO3] x 15 wherein the electronic-structural properties are intentionally modulated with depth via engineered oxygen octahedra rotations/tilts and A-site displacements. Our unit-cell resolved measurements reveal significant transformations in the local chemical and electronic valence-band states, which are consistent with the layer-resolved first-principles theoretical calculations, thus opening the door for future depth-resolved studies of a wide variety of heteroengineered material systems.

The present investigation deals with the development, characterization and application of nano-structured Pd doped Ni electrodes (Pd@Ni), which uses the electrochemical properties of Pd in synergy with the magnetic properties of Ni for biosensors development. The Pd@Ni electrodes have been characterized by X-ray diffraction, scanning electron microscopy with energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy. It has been shown that palladium presented spherical assemblies ranging 150-200 nm medium diameter size that covers large areas of the electrode surface while metallic nickel, which confers magnetic properties, showed a uniform granular structure with sizes between 20 and 50 nm. Cyclic voltammetry and electrochemical impedance spectroscopy were performed to understand the electrochemical process at the Pd@Ni electrodes in neutral media. The Pd@Ni electrodes were applied for the electrochemical detection of H2O2. Finally, Ni nanoparticles (NiNP) functionalized with the model enzyme glucose oxidase (GOx-NiNP) have been attached to the Pd@Ni electrode solely through magnetic interactions, and the obtained GOx-NiNP/Pd@Ni biosensor applied for glucose determination in aqueous solutions by fixed potential amperometry at -0.05 V (vs Ag/AgCl) with reduced interferences. (C) 2019 Elsevier Ltd. All rights reserved.

N-doped defective graphene [(N)G] obtained by pyrolysis at 900 degrees C of chitosan contains about 3.7% of residual N atoms, distributed as pyridinic, pyrrolic and graphitic N atoms. It has been found that (N)G acts as basic catalyst promoting two classical C-C bond forming nucleophilic additions in organic chemistry, such as the Michael and the Henry additions. Computational calculations at DFT level of models corresponding to the various N atoms leads to the conclusion that N atoms are more stable at the periphery of the graphene sheets and that H adsorption on these sites is a suitable descriptor to correlate with the catalytic activity of the various sites. According to these calculations the most active sites are pyridinic N atoms at zig-zag edges of the sheets. In addition, N as dopant changes the reactivity of the neigh. bour C atoms. Water was found a suitable solvent to achieve high conversions in both reactions. In this solvent the initial distribution of N atoms is affected due to the easy protonation of the N-py to N-pyH sites. As an effect, C edge sites adjacent at N-PyH with an appropriate reactivity towards the alpha-C-H bond breaking are formed. The present results show the general activity of N-doped graphene as base catalysts and illustrate the potential of carbocatalysis to promote reactions of general interest in organic synthesis. (C) 2019 Elsevier Inc. All rights reserved.

Ferroelectric capacitors based on aluminium (Al) doped hafnium oxide (HfO2) thin films grown on silicon substrates were fabricated by Atomic Layer Deposition (ALD), taking into account two methods. The first one involved the growth of a binary oxide, in a laminar way, by alternating the ALD cycles of HfO2 and Al2O3, and the second, the two precursors were sequentially mixed on the surface. The composition and structure of deposited aluminium doped hafnium oxide (Al: HfO2) thin films have been studied using X-ray photoelectron spectroscopy (XPS) and grazing incidence X-ray diffraction (GIXRD). XPS measurements show the formation of opposite ferroelectric polarization areas. Via GIXRD, it was found that the Al: HfO2 films deposited on Si have a structure with polycrystalline domains. Recording and investigation of ferroelectric domains were performed by Piezoresponse Force Microscopy (PFM), while the electrical performances of obtained devices were analysed by capacitance-voltage (C-V) and current-voltage (I-V) characteristics. The PFM measurements show there is a mechanical non-zero response even outside the written area and for an appropriate value of the electrical stress the difference in phase between successive areas is saturated to a value close to 180 degrees. The atomic force microscopy (AFM) analyses indicate a very low value of roughness average, for all grown thin films, similar to 0.2 nm, for a thickness of similar to 7 nm. From C-V characteristics, the memory window was extracted and the calculated values were found to be 0.8 V for the device obtained by the first ALD method, and 0.44 V for the second one, respectively. Moreover, in the case of the device based on the ferroelectric layer grown by the second ALD method, the memory window extends over a much wider applied voltage domain, in the range (+/- 4 V; +/- 8 V), at a signal of 100 kHz.

In this work, rapid thermal annealing (RTA) was applied to indium tin oxide (ITO) films in ambient atmosphere, resulting in significant improvements of the quality of the ITO films that are commonly used as conductive transparent electrodes for photovoltaic structures. Starting from a single sintered target (purity 99.95%), ITO thin films of predefined thickness (230 nm, 300 nm and 370 nm) were deposited at room temperature by radio-frequency magnetron sputtering (rfMS). After deposition, the films were subjected to a RTA process at 575 degrees C (heating rate 20 degrees C/s), maintained at this temperature for 10 minutes, then cooled down to room temperature at a rate of 20 degrees C/s. The film structure was modified by changing the deposition thickness or the RTA process. X-ray diffraction investigations revealed a cubic nanocrystalline structure for the as-deposited ITO films. After RTA, polycrystalline compounds with a textured (222) plane were observed. X-ray photon spectroscopy was used to confirm the beneficial effect of the RTA treatment on the ITO chemical composition. Using a Tauc plot, values of the optical band gap ranging from 3.17 to 3.67 eV were estimated. These values depend on the heat treatment and the thickness of the sample. Highly conductive indium tin oxide thin films (rho = 7.4 x 10(-5) Omega cm) were obtained after RTA treatment in an open atmosphere. Such films could be used to manufacture transparent contact electrodes for solar cells.

The competition between interface barrier in the Schottky-Mott limit and polarization driven mechanism is established during gradual formation of metal (Au) - ferroelectric (BaTiO3) interface. X-ray photoelectron spectroscopy provides core level energies and valence band positions in the contact region, to monitor the band alignment from the very first stages of metal deposition on BaTiO3. The band bending at metal/ferroelectric (FE) interface is extracted from the shift of core levels (Ba 3d, Ti 2p) as a function of the metal thickness. It is shown that the interface band alignment mechanism involves a well-defined polarization orientation washing out the bending expected from the work function difference. The sudden modification of the binding energies within ferroelectric at the first 2 angstrom Au indicates that the ferroelectric compensation mechanism triggered by the metal overlayer initiates already at ultrathin top layer, while subsequent growth contributes only at a gradual correction of the potential in the FE. The emerging picture is confirmed in first-principle calculation indicating the preferences of Au to grow preferentially to different terminated regions and to stabilize distinct ferroelectric polarization.

We report on the influence of dilute doping combined with the processing conditions on the morphological, structural, chemical states, photoluminescence and magnetic properties of Zn1-xNixO nanopowders. Ni doping changes the ZnO powder morphology from randomly-aggregated nanocrystals to densely-packed nanocrystals arranged in columnar particles, modifies the high-energy-component of O1 s spectrum and increases the modified Auger parameter in XPS, enhances the blue photoluminescence (PL) emission, suppresses the green PL emission and the intensity of the g = 1.997 EPR signal. Ni-ZnO nanostructures show room-temperature ferro-magnetism (implying they can serve as dilute magnetic semiconductors). The saturation magnetization, crystallite size and microstrain increase with the doping level; the c-axis constant and unit cell volume decrease, however, being unexpectedly higher with respect to a (reference) ZnO powder with a relaxed lattice. We demonstrate that the investigated properties were controlled by both (dilute) doping level and donor native defects produced by non-equilibrium (oxygen-deficiency and high rate of) ZnO formation.

The influence of the Gd3+ co-dopant on the structure, morphology and up-conversion luminescence/magnetic properties of the LiYF4:Gd3+/Yb3+/Er3+ nanocrystals was investigated and compared to those of Gd-free samples. Electron microscopy has indicated an inhibiting effect of the agglomeration and collapsing process of the nanocrystals compared to the Gd-free powder samples. The surface analysis of nanocrystals have not shown oxygen-metal bonds related to the metal oxidation within the surface nanometric layer. The paramagnetic properties are related to the magnetic moment of the Gd3+ ions. The up-conversion luminescence of the LiYF4:Gd3+/Yb3+/Er3+ nanocrystals is about six times stronger than in LiYF4:Yb3+/Er3+ nanocrystals; the enhancement effect is most probably due to the lattice distortion induced by the Gd co-doping.