National Institute Of Materials Physics - Romania

In this study, a sol-gel film based on lead sulfide (PbS) quantum dots incorporated into a host network was synthesized as a special nanostructured composite material with potential applications in temperature sensor systems. This work dealt with the optical, structural, and morphological properties of a representative PbS quantum dot (QD)-containing thin film belonging to the Al2O3-SiO2-P2O5 system. The film was prepared using the sol-gel method combined with the spin coating technique, starting from a precursor solution containing a suspension of PbS QDs in toluene with a narrow size distribution and coated on a glass substrate in a multilayer process, followed by annealing of each deposited layer. The size (approximately 10 nm) of the lead sulfide nanocrystallites was validated by XRD and by the quantum confinement effect based on the band gap value and by TEM results. The photoluminescence peak of 1505 nm was very close to that of the precursor PbS QD solution, which demonstrated that the synthesis route of the film preserved the optical emission characteristic of the PbS QDs. The photoluminescence of the lead sulfide QD-containing film in the near infrared domain demonstrates that this material is a promising candidate for future sensing applications in temperature monitoring.

This study aimed to exploit two invasive plant species to develop a novel, multifunctional, bioactive wound dressing based on a microporous cellulosic sponge (CS) from Gleditsia triacanthos pods and functionalizing them with Phytolacca americana fruit extract. The CS was functionalized, lyophilized, and characterized by Attenuated total reflectance-Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy, contact angle, water absorption, and retention capacity. In addition, two parameters were evaluated in temporal dynamics: controlled release of phenolic compounds and antioxidant activities. The hemolytic index, blood clotting kinetics, lactate dehydrogenase release, and wound scratch assays proved their hemo- and bio-compatibility, as well as their ability to promote cell proliferation and migration promoting-activity and to inhibit microbial growth. Furthermore, the obtained spongious material exhibited an anti-inflammatory effect by modulating the macrophages' secretion profile of IL-6 and IL-10. In conclusion, the microporous cellulosic sponge obtained from G. triacanthos could be used as a vehicle to ensure the controlled release of bioactive principles with pro-wound healing activities extracted from invasive plants. [GRAPHICS] .

A magnesium-doped hydroxyapatite in chitosan matrix (MgHApC) sample was developed as a potential platform for numerous applications in the pharmaceutical, medical, and food industries. Magnesium-doped hydroxyapatite suspensions in the chitosan matrix were obtained by the coprecipitation technique. The surface shape and morphological features were determined by scanning electron microscopy (SEM). The hydrodynamic diameter of the suspended particles was determined by Dynamic light scattering (DLS) measurements. The stability of MgHApC suspensions was evaluated by ultrasonic measurements. The hydrodynamic diameter of the MgHApC particles in suspension was 29.5 nm. The diameter of MgHApC particles calculated from SEM was 12.5 +/- 2 nm. Following the SEM observations, it was seen that the MgHApC particles have a spherical shape. The Fourier-transform infrared spectroscopy (FTIR) studies conducted on MgHApC proved the presence of chitosan and hydroxyapatite in the studied specimens. In vitro antimicrobial assays were performed on Escherichia coli ATCC 25922, Staphylococcus aureus ATCC 25923, Pseudomonas aeruginosa ATCC 27853, and Candida albicans ATCC 10231 microbial strains. The antimicrobial experiments showed that MgHApC exhibited very good antimicrobial properties against all the tested microorganisms. More than that, the results of the in vitro studies revealed that the antimicrobial properties of the samples depend on the incubation time. The evaluation of the sample's cytotoxicity was performed using the human colon cancer (HCT-8) cell line. Our results suggested the great potential of MgHApC to be used in future applications in the field of biomedical applications (e.g., dentistry, orthopedics, etc.).

Photocatalysis is one of the approaches for solving environmental issues derived from extremely harmful pollution caused by industrial dyes, medicine, and heavy metals. Titanium dioxide is among the most promising photocatalytic semiconductors; thus, in this work, TiO2 powders were prepared by a hydrothermal synthesis using titanium tetrachloride TiCl4 as a Ti source. The effect of the hydrochloric acid (HCl) concentration on TiO2 formation was analyzed, in which a thorough morpho-structural analysis was performed employing different analysis methods like XRD, Raman spectroscopy, SEM/TEM, and N-2 physisorption. EPR spectroscopy was employed to characterize the paramagnetic defect centers and the photogeneration of reactive oxygen species. Photocatalytic properties were tested by photocatalytic degradation of the rhodamine B (RhB) dye under UV light irradiation and using a solar simulator. The pH value directly influenced the formation of the TiO2 phases; for less acidic conditions, the anatase phase of TiO2 crystallized, with a crystallite size of approximate to 9 nm. Promising results were observed for TiO2, which contained 76% rutile, showing a 96% degradation of RhB under the solar simulator and 91% under UV light after 90 min irradiation, and the best result showed that the sample with 67% of the anatase phase after 60 min irradiation under the solar simulator had a 99% degradation efficiency.

Bulk MgB2 discs were prepared by an in situ route from mixtures of magnesium and boron powders. The boron powders were produced by two methods. The first one consisted of a self-propagating high tem-perature magnesiothermic synthesis (SHS) process followed by acid and fluorine cleaning and a heat treatment in inert atmosphere. This approach produced boron with purities between 86 % and 97 %, where the main impurity was Mg. Depending on the final heat treatment, these boron powders were amorphous or crystalline. In the second route, high purity nano powders (99 %) of boron were obtained by a diborane pyrolysis process. Bulks of MgB2 were characterized by structural, microstructural, and magnetic mea-surements. Critical current density, pinning force aspects and levitation force (including guiding force) details were assessed. Amorphous lower purity boron (86-97 %) obtained by the first processing route was found to promote the largest levitation forces of the MgB2 bulks and, among these samples, the best le-vitation results were recorded when using boron with a purity of 95-97 %. Use of a lower purity boron that decreases the cost of MgB2 promotes large scale production at industrial level of bulk MgB2 super-conducting magnets for levitation applications and enhances the applicability potential of MgB2 super-conductor. The relationship between levitation force and specific features of the samples such as pinning force details are discussed.& COPY; 2023 Elsevier B.V. All rights reserved.

Thick tungsten oxide layers were prepared electrophoretically in order to be used as photoanodes in photoelectrochemical water oxidation applications. The highest photocurrent density was obtained for a WO3 layer with thickness of similar to 900 nm. Additionally, WO3/BiVO4 and WO3/BiVO4/MIL-101(Fe) heterojunctions have been fabricated using WO3 layer as substrate. WO3/BiVO4 shows an increased value of the electrochemical active surface area indicating that more sites of this photoanode are activated through the formation of the heterojunction. The small V5+ signals observed in the V 2p XPS spectra of these heterojunctions were attributed to the substitution of V5+ atoms with W6+ atoms on the surface of BiVO4. Excessive W doping of the BiVO4 film determined the decrease of the photoelectrochemical performance of WO3/BiVO4 photoanode. The significant improvement of the photoconversion efficiency of the sample decorated with MIL-101(Fe) indicated that this cocatalyst provides sites more efficiently in the photoelectrochemical process. This performance was correlated with the reduced value of the charge transfer resistance at electrode/electrolyte interface obtained from electrochemical impedance spectroscopy investigation.

In this work, applications of nanohybrid composites based on titanium dioxide (TiO2) with anatase crystallin phase and single-walled carbon nanohorns (SWCNHs) as promising catalysts for the photodegradation of amoxicillin (AMOX) are reported. In this order, TiO2/SWCNH composites were prepared by the solid-state interaction of the two chemical compounds. The increase in the SWCNH concentration in the TiO2/SWCNH composite mass, from 1 wt.% to 5 wt.% and 10 wt.% induces (i) a change in the relative intensity ratio of the Raman lines located at 145 and 1595 cm(-1), which are attributed to the E-g(1) vibrational mode of TiO2 and the graphitic structure of SWCNHs; and (ii) a gradual increase in the IR band absorbance at 1735 cm(-1) because of the formation of new carboxylic groups on the SWCNHs' surface. The best photocatalytic properties were obtained for the TiO2/SWCNH composite with a SWCNH concentration of 5 wt.%, when approx. 92.4% of AMOX removal was achieved after 90 min of UV irradiation. The TiO2/SWCNH composite is a more efficient catalyst in AMOX photodegradation than TiO2 as a consequence of the SWCNHs' presence, which acts as a capture agent for the photogenerated electrons of TiO2 hindering the electron-hole recombination. The high stability of the TiO2/SWCNH composite with a SWCNH concentration of 5 wt.% is proved by the reusing of the catalyst in six photodegradation cycles of the 98.5 mu M AMOX solution, when the efficiency decreases from 92.4% up to 78%.

Vanadate glasses exhibit semiconducting property at certain temperatures. This work demonstrates the conductivity of the composition 45V(2)O(5)-25B(2)O(3)-30P(2)O(5), which is a new glass in the vanadium-boron-phosphorus ternary system that expands the glass forming area reported in literature data. The glass was obtained through a classical melt-quenching technique. The structural composition of the obtained glass was revealed with Raman spectroscopy and the amorphous characteristic has been highlighted with X-ray diffraction. The characteristic temperatures and the thermal expansion coefficient were determined by dilatometry. Based on the experimental measurements of electrical resistance, mathematical calculations were performed, resulting in a conductivity of 2.04.10(-6) S/cm at 125 degrees C, and an activation energy of 42.91 kJ/mol for this glass. Impedance spectroscopy in DC and AC at 100 V and 100 Hz to 2 MHz, respectively, showed a lower activation energy of about 0.166 eV and transition temperatures of 24 degrees C and 11 degrees C, respectively. These results were compared with those from the literature considering the temperatures at which the reported conductivities were measured. This glass has potential applications in electronic devices and temperature sensors.

We present a breakthrough in the development of novel nanocomposites based on reduced graphene oxide (RGO)-functionalized zinc oxide (ZnO) nanorods that hold exceptional promise for their use in white light emitting diodes (LEDs) and reliable UV photodetection. The nanorods had a pristine hexagonal wurtzite struc-ture, as confirmed by XRD analysis. SEM images revealed sandwich-like nanocomposites with ZnO nanorods coated in reduced graphene oxide and embedded between two layers of RGO. The study also confirmed the hybridization and interactions between the layers using Raman measurements. The resulting nanocomposites displayed a lower band gap energy than ZnO and exhibited unique photoluminescence spectra with a white PL light. The photodetector based on RGO/ZnO/RGO sandwich structures demonstrated exceptional photoresponse, with higher photocurrent under UV illumination, making it highly promising for a wide range of optoelectronic applications. Overall, this study offers a novel and powerful approach to create nanocomposite structures with enhanced optical characteristics.

The current study reports on the fabrication of composite scaffolds based on polycaprolactone (PCL) and cerium (Ce)-containing powders, followed by their characterization from compositional, structural, morphological, optical and biological points of view. First, CeO2, Ce-doped calcium phosphates and Ce-substituted bioglass were synthesized by wet-chemistry methods (precipitation/coprecipitation and sol-gel) and subsequently loaded on PCL fibres processed by electrospinning. The powders were proven to be nanometric or micrometric, while the investigation of their phase composition showed that Ce was present as a dopant within the crystal lattice of the obtained calcium phosphates or as crystalline domains inside the glassy matrix. The best bioactivity was attained in the case of Ce-containing bioglass, while the most pronounced antibacterial effect was visible for Ce-doped calcium phosphates calcined at a lower temperature. The scaffolds were composed of either dimensionally homogeneous fibres or mixtures of fibres with a wide size distribution and beads of different shapes. In most cases, the increase in polymer concentration in the precursor solution ensured the achievement of more ordered fibre mats. The immersion in SBF for 28 days triggered an incipient degradation of PCL, evidenced mostly through cracks and gaps. In terms of biological properties, the composite scaffolds displayed a very good biocompatibility when tested with human osteoblast cells, with a superior response for the samples consisting of the polymer and Ce-doped calcium phosphates.