National Institute Of Materials Physics - Romania

In this paper, we present for the first time the development of zinc-doped hydroxyapatite enriched with tetracycline (ZnHApTe) powders and provide a comprehensive evaluation of their physico-chemical and biological properties. Various techniques such as X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and Fourier transform infrared spectroscopy (FTIR) were used for the sample's complex evaluation. Moreover, the biocompatibility of zinc-doped hydroxyapatite (ZnHAp) and ZnHApTe nanoparticles was evaluated with the aid of human fetal osteoblastic cells (hFOB 1.19 cell line). The results of the biological assays suggested that these nanoparticles hold great promise as potential candidates for the future development of novel biocompatible and antimicrobial agents for biomedical applications. The antimicrobial properties of the ZnHAp and ZnHApTe nanoparticles were assessed using the standard reference microbial strains Staphylococcus aureus ATCC 25923, Escherichia coli ATCC 25922, and Candida albicans ATCC 10231. The results of the in vitro antimicrobial assay demonstrated that both tested materials exhibited good antimicrobial activity. Additionally, these data also indicated that the antimicrobial effects of the ZnHAp nanoparticles were intensified by the presence of tetracycline (Te). Furthermore, the results also suggested that the antimicrobial activity of the samples increased with the incubation time.

Adsorption and desorption of ethylene on BaO-terminated (001) barium titanate are investigated by X-ray photoelectron spectroscopy. Carbon is found in an oxidized state, at a binding energy similar to that resulting from CO adsorption on BaTiO3(001). The amount of carbon adsorbed on the surface is also similar to the case of CO/BaTiO3(001). Upon heating the substrate up to the loss of its ferroelectric polarization, the C 1s signal from the oxidized spectral region vanishes. At the same time, there was no noticeable oxygen depletion of the surface after repeated C2H4 adsorption and desorption. The substrate remains stable after repeated oxidative adsorption and desorption of ethylene. Desorption occurs at different temperatures, depending on the adsorption temperature, which suggests different adsorption geometries: non-dissociated adsorption at high temperature with ethylene bond on two surface oxygen atoms, and locally dissociated adsorption at lower temperatures, in "formaldehyde-like" local configurations.

MoS2 has proven its efficacy in flexible electronics, transistor devices, and various biological and chemical applications. However, it is still challenging to achieve large-area MoS2 monolayers with desired material quality and electrical properties to fulfill the requirement for practical applications. Moreover, the main strategy for the preparation of a 2D heterostructure it is based on the sequential stacking of the layered materials using wet or dry transfer methods which introduces many defects. This paper presents an economically viable and straightforward two-step methodology to obtain MoS2 thin films, encompassing magnetron sputtering deposition of Mo and subsequent annealing in a sulfur-rich environment. This approach successfully yielded MoS2 thin films on Si\SiO2 substrates. Additionally, heterostructures consisting of few layer graphene (FLG) and MoS2 were directly obtained using the same method. The utilization of grazing incidence X-ray diffraction verified the formation of the hexagonal MoS2 phase, a finding further confirmed by Raman spectroscopy. X-ray photoelectron spectroscopy (XPS) investigations revealed the successful sulfurization process, with surface-bound oxides forming only subsequent to air exposure. Comprehensive assessment involving X-ray reflectivity, atomic force microscopy and XPS collectively inferred the fabrication of thin films comprised of a small number of MoS2 layers covering the entire substrate. Electrical assessments exhibited an electrical hysteresis, demonstrating its potential for memristor applications. Overall, this study outlines a cost-effective fabrication method for producing nanoscale MoS2 thin films with excellent properties, avoiding the use of toxic gases such as H2S. These findings contribute to the potential development of cutting-edge applications.

Design of composite support materials based on Sn-doped TiO2 and carbon is one of the strategies to develop corrosion-resistant and CO-tolerant Pt electrocatalysts for polymer electrolyte membrane (PEM) fuel cells. As the synthesis methodology may have crucial influence on the structural and functional properties of the composites, different preparation routes for the novel support materials are explored and compared. Ti(1-x)SnxO2-C (x: 0.1-0.3) composites with different mixed oxide/carbon ratios were prepared by two sol-gel-based synthesis routes, namely (i) the introduction of a Sn precursor after the formation of the TiO2-rutile nuclei on the carbon backbone (route A), and (ii) simultaneous introduction of Ti and Sn precursors, resulting in good mixing of the Sn- and Ti-sol before the addition of the carbon (route B). The bulk and surface microstructure of the composites and the electrocatalysts obtained by their Pt-loading were investigated in detail. The incorporation of tin into the TiO2-rutile unit cell was confirmed by X-ray powder diffraction and Raman spectroscopy; the results indicated doping levels in good accordance with the amount of tin precursor. The advantages of composites and Pt electrocatalysts obtained via synthesis route B were that they do not contain segregated Sn-0 or SnO2 phases, have a more homogeneous/uniform mixed oxide distribution over the carbon backbone, and the electrochemically active surface area values (similar to 60-80 m(2)/g(Pt)) are twice as high as those of catalysts with similar compositions synthesized by method A. A common feature of the composites prepared by routes A and B was the presence of a tin oxide-rich overlayer identified by X-ray photoelectron spectroscopy. As a consequence, the electrocatalytic behavior of the catalysts was not influenced by the Ti/Sn ratio and was mainly dependent on the synthesis method used in the preparation of composite support materials. Elemental maps confirmed the formation of areas where Pt and the Sn doping element were in atomic proximity to each other, which means a favorable interaction either for the bifunctional mechanism or the electronic ligand effect. An increase in carbon content in composite materials led to an increase in both catalytic activity and long-term stability. The results of electrochemical studies showed that Sn-containing Pt catalysts with a high carbon content (75 wt%) are the most promising for potential use both as an anode and a cathode for PEM fuel cells.

The hydroxyapatite and copper-doped hydroxyapatite coatings (Ca10-xCux(PO4)6(OH)2; xCu = 0, 0.03; HAp and 3CuHAp) were obtained by the vacuum deposition technique. Then, both coatings were analyzed by the X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and water contact angle techniques. Information regarding the in vitro antibacterial activity and biological evaluation were obtained. The XRD studies confirmed that the obtained thin films consist of a single phase associated with hydroxyapatite (HAp). The obtained 2D and 3D SEM images did not show cracks or other types of surface defects. The FTIR studies' results proved the presence of vibrational bands characteristic of the hydroxyapatite structure in the studied coating. Moreover, information regarding the HAp and 3CuHAp surface wettability was obtained by water contact angle measurements. The biocompatibility of the HAp and 3CuHAp coatings was evaluated using the HeLa and MG63 cell lines. The cytotoxicity evaluation of the coatings was performed by assessing the cell viability through the MTT assay after incubation with the HAp and 3CuHAp coatings for 24, 48, and 72 h. The results proved that the 3CuHAp coatings exhibited good biocompatible activity for all the tested intervals. The ability of Pseudomonas aeruginosa 27853 ATCC (P. aeruginosa) cells to adhere to and develop on the surface of the HAp and 3CuHAp coatings was investigated using AFM studies. The AFM studies revealed that the 3CuHAp coatings inhibited the formation of P. aeruginosa biofilms. The AFM data indicated that P. aeruginosa's attachment and development on the 3CuHAp coatings were significantly inhibited within the first 24 h. Both the 2D and 3D topographies showed a rapid decrease in attached bacterial cells over time, with a significant reduction observed after 72 h of exposure. Our studies suggest that 3CuHAp coatings could be suitable candidates for biomedical uses such as the development of new antimicrobial agents.

In view of their potential applicability in technology fields where magnets are required to operate at higher temperatures, the class of nanocomposite magnets with little or no rare earth (RE) content has been widely researched in the last two decades. Among these nanocomposite magnets, the subclass of magnetic binary systems exhibiting the formation of L10 tetragonal phases is the most illustrious. Some of the most interesting systems are represented by the Mn-based alloys, with addition of Al, Bi, Ga, Ge. Such alloys are interesting as they are less costly than RE magnets and they show promising magnetic properties. The paper tackles the case of MnGa binary alloys with various compositions around the Mn3Ga stoichiometry. Four MnGa magnetic alloys, with Mn content ranging from 70 at% to 75 at% were produced using rapid solidification to form the melt. By combining structural information arising from X-ray diffractometry and transmission electron microscopy with magnetic properties determined by vibrating sample magnetometry, we are able to document the nature and properties of the structural phases formed in the alloys in their as-cast state and upon annealing, the evolution of the phase structure after annealing and its influence on the magnetic behavior of the MnGa alloys. After annealing at 400 degrees C and 500 degrees C, MnGa alloys are showing a multiple-phase microstructure, consisting of co-existing crystallites of L10 and D022 tetragonal phase. As a consequence of these structurally and magnetically different phases, co-existing within the microstructure, promising magnetic features are obtained, with both coercive fields and saturation magnetization exceeding values previously reported for both alloys and layers of MnGa.

The development of kesterite (Cu2ZnSn(S,Se)4, CZTSSe) thin films for photovoltaic applications is highly necessary, given their composition of Earth-abundant, environmentally friendly elements and their compatibility with established photovoltaic technologies. This study presents a novel synthesis approach for CZTSSe films with varied S/(S+Se) ratios, ranging from 0.83 to 0.44, by a two-step magnetron sputtering deposition/annealing process. The first step consists in an initial deposition of stacked Mo/SnS2/Cu layers, which, upon thermal treatment in a sulfur atmosphere, were transformed into Cu2SnS3 (CTS) films. In the second step, further deposition of ZnSe and subsequent annealing in a tin and selenium atmosphere resulted in the formation of a CZTSSe phase. These processes were optimized to fabricate high-quality and single-phase CZTSSe films, thereby mitigating the formation of secondary phases. Characterization techniques, including scanning electron microscopy, demonstrated a clear correlation between decreased S/(S+Se) ratios and enhanced film densification and grain size. Moreover, grazing incidence X-ray diffraction and Raman spectroscopy confirmed a compositional and structural transition from close to CZTS to nearly a CZTSe phase as the S/(S+Se) ratios decreased. This study advances kesterite-based solar cell technology by enhancing the structural properties and crystallinity of the absorber layer, necessary for improving photovoltaic performance.

This work presents the synthesis of tungsten nanoparticles (W NPs) using a cluster source based on magnetron sputtering combined with gas aggregation (MSGA), operated with up to 81% H-2 in the hydrogen/argon mixture used as a working gas. The results show that, with up to 41% H-2 in discharge, the synthesis rate increases by more than 60 times, rapidly decreasing for over 50% H-2 in discharge. The W dust is still produced for H-2-dominated discharges (81%), and its deposition rate is small but not negligible (0.02 mg/h). The obtained W NPs are isolated, with the diameter decreasing from 50 nm to 15 nm when the amount of H-2 in discharge is smaller than 41%. Over this value, the particles tend to agglomerate, forming structures similar to film-like deposits. Also, the diameter of the dust spots deposited on substrates depends on the H-2 content of the discharge. This allows the efficient coating of substrates up to 26 mm wide by translating them in front of the MSGA cluster source exit aperture. Additionally, for 41% H-2 in discharge, the influence of synthetic air leaks (0%-8.2%) in discharge was investigated. The deposition rate decreases rapidly (ceasing for around 6% air in discharge), and the obtained nanoparticles tend to agglomerate on the substrate (at 3.3% air content, the dust deposit has the aspect of a near-continuous film). Chemical composition investigations show a pronounced tendency for oxidation, nitridation, and oxynitride formation in the presence of air leaks.

Two-dimensional materials are currently among the most intensively studied topics in condensed matter physics because of their intriguing properties and the possibilities of integration in future electronic device applications. Image potential states, i.e. two-dimensional unoccupied electronic states that are confined in front of a surface, can provide detailed information on work function, electric field effects, charge transfer, charge injection, and charge dynamics at surfaces. This information is essential to understand and tailor the properties of twodimensional materials for electronic device applications. In this work, we briefly review recent developments in the detection and analysis of image potential states in single- and multilayered two-dimensional materials, heterostructures thereof, and nanostructures, such as nanoislands and nanoribbons. We also address several issues that can have an effect on image potential states, such as the preparation method, quality of the material, defects, interfacial interactions, and interactions with the substrate.

TiO2 nanoparticles (NPs) doped with W (W:TiO2), double-doped with W and V (W&V:TiO2), and loaded with noble metals (W:TiO2 @Pt/Pd/Ag and W&V:TiO2@Pt/Pd/Ag) were synthesized by laser pyrolysis followed by chemical impregnation and reduction. Due to its exceptional properties, TiO2 is considered a key material being used in a wide range of applications. To improve its detection activity, the increase in the specific surface of the material, and the presence of defects in its structure play a decisive role. Doped and double-doped TiO2 nanoparticles with dimensions in the range of 25-30 nm presented a mixture of phases corresponding to titania, with the anatase phase accounting for the majority (95%). By loading these nanoparticles with small particles of noble metals, a significant increase in the specific surface area by three or even five times the original values was achieved. Sensitive thin films for surface acoustic wave (SAW) sensors were made with the NPs, embedded in polyethyleneimine (PEI) polymer and deposited by spin-coating. Each sensor was tested at CH4 concentrations between 0.4 and 2%, at room temperature, and the best results were obtained by the sensor with NPs doped with V and decorated with Pd, with a limit of detection (LOD) of 17 ppm, due to the strong catalytic effect of Pd.