The development of new thin-film cathodes triggered a recent research interest in energy storage applications. Over the past years, vanadium oxides have been extensively explored as promising electrodes for batteries owing to their rich valence states and remarkable electrochemical properties. Herein, we report on the synthe-sis of undoped and Sn doped V2O3 thin-films on graphene (G)/Al foil by pulsed laser deposition followed by rapid thermal annealing in N2 at low temperature (similar to 430 degrees C). The obtaining V2O3 phase on graphene/Al foil (G/Al) has been confirmed by X-ray diffraction and Raman and X-ray photoelectron spectroscopy analyses. The synthesized vanadium oxide films were tested as cathodes in coin cells. The electrochemical properties have been systematically investigated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and galvanostatic charge discharge (GCD) measurements. A superior electrochemical performance was observed for the V2O3 on G/Al structures, with an initial capacity of around 300 mAh g-1, with respect to the bare G/Al electrode. The use of the Sn-doped (5 mol%) V2O3 thin-films improved slightly the initial capac-ity up to a value of ca. 311 mAh g-1. Both V2O3/G/Al and Sn-doped V2O3/G/Al exhibited excellent cycling performances after 40 cycles with a capacity maintenance at a C-rate C/20 of 317 mAh g-1. Long-term cycling test (up to 200 cycles) showed that the Sn doping could be an excellent strategy to improve the stability of the electrodes, which yielded a capacity loss of only 0.128% per cycle. Possible mechanisms are presented and dis-cussed. This work could serve as point of reference for future developments in the field of batteries employing vanadium oxide-based thin-films deposited by physical vapor deposition techniques.

The attraction towards Ti and its alloys reside in their superior mechanical and tribological features, as compared to CaPs, which are renowned for their compositional and structural features similar to those of natural bones. However, Ti-based materials suffer from limited biocompatibility and inertness when implanted for extended periods. As such, surface modification with ceramic coatings is required in order to achieve proper biomedical features and enhance their overall behavior in the human body. Hence, this study outlined for the first time the prospect of coating several Ti6Al4V substrates (disks) with bovine-bone derived hydroxyapatite (HA) by laser cladding technique with pre-placed slurry. During laser processing the input materials merge depending on the heating rate/temperature and clad materials. The proposed sample preparation set-up, followed for the first time in this study, involved the concomitant modulation of two parameters: the natural HA ratio (100 wt%, and 50 wt % HA + 50 wt% Ti blends) and laser beam power (500-1000 W range). The laser beam was applied after the ceramic slurries (prepared HA/HA-based blends mixed with polyvinyl alcohol) were placed inside the priorly machined channels on the metallic Ti disks. Partially overlapped cladding tracks (similar to 30% overlapping ratio) resulted and the investigations were further performed in cross-section view. The structural analyses confirmed the formation of calcium titanate as main phase for all samples and the arrest of HA only for those prepared with 100% HA ratio at low to medium laser powers. In addition, the morpho-compositional evaluation revealed the formation of a fully ceramic coating only for the latter sample sets. Further, the surface wettability (contact angle and surface free energy) and Vickers micro-hardness results led to the selection of the optimal technological parameters for the development of ceramic cladded layers with prospect compatibility with regenerative med-icine applications.

Photocatalysis is one of the approaches for solving environmental issues derived from extremely harmful pollution caused by industrial dyes, medicine, and heavy metals. Titanium dioxide is among the most promising photocatalytic semiconductors; thus, in this work, TiO2 powders were prepared by a hydrothermal synthesis using titanium tetrachloride TiCl4 as a Ti source. The effect of the hydrochloric acid (HCl) concentration on TiO2 formation was analyzed, in which a thorough morpho-structural analysis was performed employing different analysis methods like XRD, Raman spectroscopy, SEM/TEM, and N-2 physisorption. EPR spectroscopy was employed to characterize the paramagnetic defect centers and the photogeneration of reactive oxygen species. Photocatalytic properties were tested by photocatalytic degradation of the rhodamine B (RhB) dye under UV light irradiation and using a solar simulator. The pH value directly influenced the formation of the TiO2 phases; for less acidic conditions, the anatase phase of TiO2 crystallized, with a crystallite size of approximate to 9 nm. Promising results were observed for TiO2, which contained 76% rutile, showing a 96% degradation of RhB under the solar simulator and 91% under UV light after 90 min irradiation, and the best result showed that the sample with 67% of the anatase phase after 60 min irradiation under the solar simulator had a 99% degradation efficiency.

The incorporation of therapeutic-capable ions into bioactive glasses (BGs), either based on silica (SBGs) or phosphate (PBGs), is currently envisaged as a proficient path for facilitating bone regeneration. In conjunction with this view, the single and complementary structural and bio-functional roles of CuO and Ga2O3 (in the 2-5 mol% range) were assessed, by deriving a series of SBG and PBG formulations starting from the parent glass systems, FastOs (R) BG -38.5SiO2-36.1CaO-5.6P2O5-19.2MgO-0.6CaF2, and 50.0P2O5-35.0CaO-10.0Na2O-5.0 Fe2O3 (mol%), respectively, using the process of melt-quenching. The inter-linked physico-chemistry -biological response of BGs was assessed in search of bio-functional triggers. Further light was shed on the structural role -as network former or modifier -of Cu and Ga, immersed in SBG and PBG matrices. The preliminary biological performance was surveyed in vitro by quantification of Cu and Ga ion release under homeostatic conditions, cytocompatibility assays (in fibroblast cell cultures) and antibacterial tests (against Staphylococcus aureus). The similar (Cu) and dissimilar (Ga) structural roles in the SBG and PBG vitreous networks governed their release. Namely, Cu ions were leached in similar concentrations (ranging from 10-35 ppm and 50-110 ppm at BG doses of 5 and 50 mg/mL, respectively) for both type of BGs, while the release of Ga ions was 1-2 orders of magnitude lower in the case of SBGs (i.e., 0.2-6 ppm) compared to PBGs (i.e., 9-135 ppm). This was attributed to the network modifier role of Cu in both types of BGs, and conversely, to the network former (SBGs) and network modifier (PBGs) roles of Ga. All glasses were cytocompatible at a dose of 5 mg/mL, while at the same concentration the antimicrobial efficiency was found to be accentuated by the coupled release of Cu and Ga ions from SBG. By collective assessment, the most prominent candidate material for the further development of implant coatings and bone graft substitutes was delineated as the 38.5SiO2-34.1CaO-5.6P2O5-16.2MgO-0.6CaF2-2.0CuO-3.0Ga2O3 (mol%) SBG system, which yiel-ded moderate Cu and Ga ion release, excellent cytocompatibility and marked antibacterial efficacy. (c) 2021 The Chinese Ceramic Society. Production and hosting by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).

Understanding the phonon anharmonicity and temperature-dependent behavior of phonons that affect the thermal transport properties in 2D materials is crucial for developing efficient thermoelectric and memristor devices. SnSe has attracted significant interest because of its potential applications for developing such novel devices. Here, orthorhombic SnSe nanoflakes with a thickness of less than 100 nm and oriented along the [100] crystal axis were obtained using physical vapor transport at atmospheric pressure. Polarization-resolved Raman spectroscopy of SnSe nanoflakes was performed at a temperature of 5 K. Temperature-dependent frequencies and linewidths of Raman modes in tin selenide were fitted according to the anharmonic phonon coupling theory. The results indicate that both two and three order processes are responsible for the phonon decay in tin selenide. The memristive property was confirmed by electrical measurements of SnSe devices. SnSe memristors have an operating current of 10-4 A, similar to other transition-metal dichalcogenide memristors, but are more energy efficient than memristors based on defect migration, with a threshold voltage of 3 V.

The investigation of the effect of carbon nanomaterials and lipids on the aggregation particularities of the amyloid beta/A beta(1-42) layers is important for understanding the generation mechanism of neuronal disorder and how it can be inhibited. Additionally, amyloids are nanomaterials with a wide area of potential applications from nanotechnology to biotechnology. This paper presents a study about the preparation of A beta(1-42) layer by two different methods, Langmuir-Blodgett (L-B) and drop cast (DC), on Si and Si covered by a layer of Buckminster fullerene, C-60, and on the effect of fullerene layer or/and cholesterol (Ch) on the generation of A beta(1-42) secondary structure forms, relevant for specific applications. AFM, SEM FTIR and Raman analysis offered details about the layer surface topography, morphology and particularities of the secondary structure generated in the process of A beta(1-42) molecules aggregation. This study showed that the presence of Ch inhibited the formation of fibrils in A beta(1-42) film deposited by L-B on Si covered by C-60 The structures developed during aggregation were correlated with the topography and roughness of the films. The presence of Ch determined a decrease in roughness for L-B film and increase in roughness for DC film deposited on Si covered by C-60 layer.

Currently, there is a considerable time-lag in the industrialisation of innovative technological solutions for the functionalization of osseous implants, with ever-demanding healthcare requirements (e.g., controlled release of therapeutic ions, match of biomaterial degradation - bone growth rates, antimicrobial efficiency). As third-generation biomaterials, phosphate bio-glasses (PBGs) have demonstrated an ability to stimulate specific biological responses from tissue to molecular level, by successfully coupling bioactive and resorbable material properties. Here, radio-frequency magnetron sputtered (RF-MS) PBGs were explored as sacrificial resorbable layers for prospective biomedical implant designs. A PBG powder with a 50-P2O5, 35-CaO, 10-Na2O and 5-Fe2O3 composition (mol%) was used as source (target) material. The influence of the argon working pressure (0.2-1 Pa) - one of the most prominent RF-MS variables - on the morphology, structure, uniformity, composition, degradation rate and cytocompatibility of PBG films was investigated. The engineered modification of physical-chemical and biological features of the PBG sputtered films was multi-parametrically surveyed by AFM, EDXS, spectroscopic ellipsometry, GIXRD, FTIR spectroscopy measurements and in vitro assays. Results suggested that the film thickness, composition, density and structure were preserved over a uniformity region having a diameter of similar to 30 mm, irrespective of sputtering pressure. The network connectivity and the surface porosity of the films were found to have antagonistic roles with respect to the in vitro degradation performance. The possibility of fine tuning the composition, structure and thereby biological interaction of the PBG films by conveniently modifying the sputtering pressure was shown (i.e., permitting their complete controlled degradation, without cytotoxic effects). This work is the first to show in vitro cytocompatibility outcomes of sputtered PBG films and their cross-area uniformity, and thus, it could prove to be an important technological step in their future biomedical application and suggest implications for future industrial scale-up.

Cation-substituted hydroxyapatite (HA), standalone or as a composite (blended with polymers or metals), is currently regarded as a noteworthy candidate material for bone repair/regeneration either in the form of powders, porous scaffolds or coatings for endo-osseous dental and orthopaedic implants. As a response to the numerous contradictions reported in literature, this work presents, in one study, the physico-chemical properties and the cytocompatibility response of single cation-doped (Ce, Mg, Sr or Zn) HA nanopowders in a wide concentration range (0.5-5 at.%). The modification of composition, morphology, and structure was multiparametrically monitored via energy dispersive X-ray, X-ray photoelectron, Fourier-transform infrared and micro-Raman spectroscopy methods, as well as by transmission electron microscopy and X-ray diffraction. From a compositional point of view, Ce and Sr were well-incorporated in HA, while slight and pronounced deviations were observed for Mg and Zn, respectively. The change of the lattice parameters, crystallite size, and substituting cation occupation factors either in the Ca(I) or Ca(II) sites were further determined. Sr produced the most important HA structural changes. The in vitro biological performance was evaluated by the (i) determination of leached therapeutic cations (by inductively coupled plasma mass spectrometry) and (ii) assessment of cell behaviour by both conventional assays (e.g., proliferation-3-(4,5-dimethyl thiazol-2-yl) 5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium assay; cytotoxicity-lactate dehydrogenase release assay) and, for the first time, real-time cell analysis (RTCA). Three cell lines were employed: fibroblast, osteoblast, and endothelial. When monophasic, the substituted HA supported the cells' viability and proliferation without signs of toxicity. The RTCA results indicate the excellent adherence of cells. The study strived to offer a perspective on the behaviour of Ce-, Mg-, Sr-, or Zn-substituted HAs and to deliver a well-encompassing viewpoint on their effects. This can be highly important for the future development of such bioceramics, paving the road toward the identification of candidates with highly promising therapeutic effects.

Bovine hydroxyapatite (BHA) and BHA blended with clinoptilolite (CLIN) and alumina (Al2O3) coatings were synthesized using pulsed laser deposition (PLD) with a KrF* excimer laser source (lambda = 248 nm, tau(FWHM) <= 25 ns). Physical-chemical characteristics and the potential use of coatings for preventing bacteria adhesion and biofilm formation were investigated. Optimized PLD conditions were selected for coatings with rough morphologies, suitable for good cell adhesion and implant anchorage and good replication of the source target composition. The crystallinity of composite coatings was progressively decreasing with the augment of the Al2O3 and CLIN contents, which in turn can facilitate an efficacious release of active components. Al2O3- and CLIN-containing coatings exhibited high cytocompatibility and specific antibiofilm profiles, preventing the initiation and maturation of bacterial biofilms. Optimum biological activity profiles associated with the use of sustainable and/or inexpensive materials are, in our opinion, of key importance for the future development of performant implant coatings, which should he perfectly compatible with the surrounding tissue while preventing postsurgical endogenous or nosocomial infections.

This study aims to obtain uniform and homogeneous bismuth germanate oxides thin films by spin coating and using the sol-gel technique with different precursors, followed by low-temperature annealing at 560 degrees C. By using Bi(NO3)(3) precursors, we have obtained transparent, yellowish thin films with a 200 nm thickness. The structural analysis of the initial sol-gel powder has shown the presence of two crystalline structures, the cubic Bi4Ge3O12 (BGO) and monoclinic Bi2GeO5 crystallites, which evolves towards the BGO structure after annealing. The elemental analysis confirmed the composition of the desired compound Bi4Ge3O12 with 60 wt % GeO2 and 40 wt % Bi2O5. On the other hand, by changing the precursor to (Bi(CH3COO)(2), the film thickness increased to 500 nm thicker due to the high viscosity of the sol, and a dominant monoclinic Bi2GeO5 crystalline structure appeared. The elemental analysis revealed a nonstoichiometric composition with 38 wt % GeO2 and 62 wt % Bi2O3. Due to the low GeO2 phase content that reacted with metastable Bi2GeO5, we obtained cubic Bi4Ge3O12 as a secondary phase, with Bi2GeO5 as a dominant crystalline phase. The redshifts of both absorptions and emissions spectra peaks confirmed a different disorder structure as an interplay between the cubic Bi4Ge3O12 (BGO) and monoclinic Bi2GeO5 phases.

Silica-based bioactive glasses (SBG) hold great promise as bio-functional coatings of metallic endo-osseous implants, due to their osteoproductive potential, and, in the case of designed formulations, suitable mechanical properties and antibacterial efficacy. In the framework of this study, the FastOs(R)BG alkali-free SBG system (mol%: SiO2-38.49, CaO-36.07, P2O5-5.61, MgO-19.24, CaF2-0.59), with CuO (2 mol%) and Ga2O3 (3 mol%) antimicrobial agents, partially substituting in the parent system CaO and MgO, respectively, was used as source material for the fabrication of intentionally silica-enriched implant-type thin coatings (similar to 600 nm) onto titanium (Ti) substrates by radio-frequency magnetron sputtering. The physico-chemical and mechanical characteristics, as well as the in vitro preliminary cytocompatibility and antibacterial performance of an alkali-free silica-rich bio-active glass coating designs was further explored. The films were smooth (R-RMS < 1 nm) and hydrophilic (water contact angle of similar to 65 degrees). The SBG coatings deposited from alkali-free copper-gallium co-doped FastOs(R)BG-derived exhibited improved wear performance, with the coatings eliciting a bonding strength value of similar to 53 MPa, Lc3 critical load value of similar to 4.9 N, hardness of similar to 6.1 GPa and an elastic modulus of similar to 127 GPa. The Cu and Ga co-doped SBG layers had excellent cytocompatibility, while reducing after 24 h the Staphylococcus aureus bacterial development with 4 orders of magnitude with respect to the control situations (i.e., nutritive broth and Ti substrate). Thereby, such SBG constructs could pave the road towards high-performance bio-functional coatings with excellent mechanical properties and enhanced biological features (e.g., by coupling cytocompatibility with antimicrobial properties), which are in great demand nowadays.

In this study, the results about the influence of the surface morphology of layers based on montmorillonite (MMT) and silver (Ag) on antimicrobial properties are reported. The coating depositions were performed in the plasma of a radio frequency (RF) magnetron sputtering discharge. The studied layers were single montmorillonite layers (MMT) and silver/montmorillonite multilayers (MMT-Ag) obtained by magnetron sputtering technique with a different surface thickness. The resultant MMT-Ag biocomposite multilayers exhibited a uniform distribution of constituent elements and enhanced antimicrobial properties against fungal biofilm development. Glow-discharge optical emission spectroscopy (GDOES) analysis revealed the formation of MMT-Ag biocomposite multilayers following the deposit of a silver layer for an MMT layer that was initially deposited on a Si substrate. The surface morphology and thickness evaluation of deposited biocomposite layers were performed by scanning electron microscopy (SEM). A qualitative analysis of the chemical composition of thin layers was performed and the elements O, Ag, Mg, Fe, Al, and Si were identified in the MMT-Ag biocomposite multilayers. The in vitro antifungal assay proved that the inhibitory effect against the growth of Candida albicans ATCC 101231 CFU was more emphasized in the case of MMT-Ag biocomposite multilayers that in the case of the MMT layer. Cytotoxicity studies performed on HeLa cells showed that the tested layers did not show significant toxicity at the time intervals during which the assay was performed. On the other hand, it was observed that the MMT layers exhibited slightly higher biocompatible properties than the MMT-Ag composite layers.

High-performance bioceramics are required for preventing failure and prolonging the life-time of bone grafting scaffolds and osseous implants. The proper identification and development of materials with extended functionalities addressing socio-economic needs and health problems constitute important and critical steps at the heart of clinical research. Recent findings in the realm of ion-substituted hydroxyapatite (HA) could pave the road towards significant developments in biomedicine, with an emphasis on a new generation of orthopaedic and dentistry applications, since such bioceramics are able to mimic the structural, compositional and mechanical properties of the bone mineral phase. In fact, the fascinating ability of the HA crystalline lattice to allow for the substitution of calcium ions with a plethora of cationic species has been widely explored in the recent period, with consequent modifications of its physical and chemical features, as well as its functional mechanical and in vitro and in vivo biological performance. A comprehensive inventory of the progresses achieved so far is both opportune and of paramount importance, in order to not only gather and summarize information, but to also allow fellow researchers to compare with ease and filter the best solutions for the cation substitution of HA-based materials and enable the development of multi-functional biomedical designs. The review surveys preparation and synthesis methods, pinpoints all the explored cation dopants, and discloses the full application range of substituted HA. Special attention is dedicated to the antimicrobial efficiency spectrum and cytotoxic trade-off concentration values for various cell lines, highlighting new prophylactic routes for the prevention of implant failure. Importantly, the current in vitro biological tests (widely employed to unveil the biological performance of HA-based materials), and their ability to mimic the in vivo biological interactions, are also critically assessed. Future perspectives are discussed, and a series of recommendations are underlined.