National Institute Of Materials Physics - Romania

In the view of the advantages of using P, N, Si and graphene oxide (GO) for the development of flame retardants materials, a multi-structure synergistic composite was synthesized by grafting a novel nitrogen-containing polyhedral oligomeric silsesquioxane (HAK) and 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) on the surface of GO nanosheet. In the first step, 2-hydroxyethyl acrylate was selectively reacted, and then, HAK was synthetized by the condensation of the aza-Michael addition product with 3-(methacryloyloxy)propyltrimethoxysilane. Finally, the GO obtained by an innovative variant of Marcano-Tour improved exfoliation method was functionalized, first with DOPO, and then with HAK. The structural, morphological and surface properties of GO and GO-DOPO-HAK were investigated by means of XRD, TEM-EDX, FT-IR, Raman, zeta potential and XPS techniques, and it was evidenced the functionalization of GO with DOPO, and then with HAK. The performed microscale combustion calorimetry (MCC) and TG measurements indicated a great potential of the GO-DOPO-HAK as flame retardant material as the obtained residual weight for this sample was found to be the highest one compared to the other investigated samples. MCC analyses further revealed a major decrease in heat release capacity (HRC) and a significant increase in char yield, results that confirm the great potential of GO-DOPO-HAK as flame retardancy material. [GRAPHICS] .

Novel biomaterials with promising bone regeneration potential, derived from rich, renewable, and cheap sources, are reported. Thus, thin films were synthesized from marine-derived (i.e., from fish bones and seashells) hydroxyapatite (MdHA) by pulsed laser deposition (PLD) technique. Besides the physical-chemical and mechanical investigations, the deposited thin films were also evaluated in vitro using dedicated cytocompatibility and antimicrobial assays. The morphological examination of MdHA films revealed the fabrication of rough surfaces, which were shown to favor good cell adhesion, and furthermore could foster the in-situ anchorage of implants. The strong hydrophilic behavior of the thin films was evidenced by contact angle (CA) measurements, with values in the range of 15-18 degrees. The inferred bonding strength adherence values were superior (i.e., similar to 49 MPa) to the threshold established by ISO regulation for high-load implant coatings. After immersion in biological fluids, the growth of an apatite-based layer was noted, which indicated the good mineralization capacity of the MdHA films. All PLD films exhibited low cytotoxicity on osteoblast, fibroblast, and epithelial cells. Moreover, a persistent protective effect against bacterial and fungal colonization (i.e., 1- to 3-log reduction of E. coli, E. faecalis, and C. albicans growth) was demonstrated after 48 h of incubation, with respect to the Ti control. The good cytocompatibility and effective antimicrobial activity, along with the reduced fabrication costs from sustainable sources (available in large quantities), should, therefore, recommend the MdHA materials proposed herein as innovative and viable solutions for the development of novel coatings for metallic dental implants.

Despite the high coercive field (E-c = 7.3 kV/mm) and the high conductivity (2.1 x 10(-7) (omega m)(-1)) of (Bi0.5Na0.5)TiO3 (BNT) ceramics, their microstructure and electric properties can be tailored by appropriate substitutions at the A and/or B-sites. In this paper, we offer a comprehensive review of the up-to-date advances on doped lead-free BNT ceramics, highlighting the role of the nature and concentration of dopants on the stoichiometry, microstructure, density, dielectric properties, and piezoelectric properties of the solid solutions obtained after doping. For each composition presented in this review, the synthesis method and the sintering technique of the ceramics are also given because of the well-known connection between powder processing (its morphology), ceramics densification (its density), and the macroscopic properties of the final product. A substitution mechanism for each dopant that explains the role of the dopant on the structure and electrical properties of the BNT matrix is also described in detail. Our review provides knowledge for the development of new solid solutions of BNT.

We studied here the influence of Li+ ions on the benzene rings of nematic mixture E7, which is electrochemically adsorbed onto gold electrode surface, to highlight the ability of this mixture for the applications in the field of the rechargeable Li+-ion batteries. Raman spectra support the changes observed in electrochemical analyses while contact angle measurements show that wetting properties of E7 layer were modified after deposition of this mixture onto gold support and the doping with Li+ ions.

Replacing lead atoms in halide perovskite materials is of significant importance for the development of environmentally friendly perovskite solar cells. In this paper, we investigated the effect of doping the MAPbI(2.6)Cl(0.4) hybrid perovskite (MA-methyl ammonium) with non-toxic elements, such as alkaline earth metal ions (Mg2+) and transition metal ions (Zn2+). The structural, morphological, and optical properties of the prepared samples were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and UV-Vis. spectroscopy. Finally, the doped films were used as photoactive layers in solar devices in order to evaluate their photovoltaic performance. Zn proved to be more appropriate to replace partially Pb and films with higher quality were obtained. As a result, the MAPb1(-x)Zn(x)I(2.6)Cl(0.4) based solar cells have demonstrated a slight improvement of the photovoltaic performances, resulting in a uniform and narrower PCEs (power conversion efficiency) range, compared to pristine MAPbI(2.6)Cl(0.4) based devices.

Bortezomib is an inhibitor of proteasomes and an anti-cancer drug. Although bortezomib is considered a safe drug, as confirmed by cytotoxicity assays, recent reports highlighted the possibility of interaction between bortezomib and cellular components, with detrimental long-term effects. The evaluation of the interaction between bortezomib and dsDNA was investigated in bulk solution and using a dsDNA electrochemical biosensor. The binding of bortezomib to dsDNA involved its electroactive centers and led to small morphological modifications in the dsDNA double helix, which were electrochemically identified through changes in the guanine and adenine residue oxidation peaks and confirmed by electrophoretic and spectrophotometric measurements. The redox product of bortezomib amino group oxidation was electrochemically generated in situ on the surface of the dsDNA electrochemical biosensor. The redox product of bortezomib was shown to interact primarily with guanine residues, preventing their oxidation and leading to the formation of bortezomib-guanine adducts, which was confirmed by control experiments with polyhomonucleotides electrochemical biosensors and mass spectrometry. An interaction mechanism between dsDNA and bortezomib is proposed, and the formation of the bortezomib redox product-guanine adduct explained.

Using the microwave-assisted sol-gel method, Zn- and Cu-doped TiO2 nanoparticles with an anatase crystalline structure were prepared. Titanium (IV) butoxide was used as a TiO2 precursor, with parental alcohol as a solvent and ammonia water as a catalyst. Based on the TG/DTA results, the powders were thermally treated at 500 degrees C. XRD and XRF revealed the presence of a single-phase anatase and dopants in the thermally treated nanoparticles. The surface of the nanoparticles and the oxidation states of the elements were studied using XPS, which confirmed the presence of Ti, O, Zn, and Cu. The photocatalytic activity of the doped TiO2 nanopowders was tested for the degradation of methyl-orange (MO) dye. The results indicate that Cu doping increases the photoactivity of TiO2 in the visible-light range by narrowing the band-gap energy.

We studied here the influence of Li+ ions on the benzene rings of nematic mixture E7, which is electrochemically adsorbed onto gold electrode surface, to highlight the ability of this mixture for the applications in the field of the rechargeable Li+-ion batteries. Raman spectra support the changes observed in electrochemical analyses while contact angle measurements show that wetting properties of E7 layer were modified after deposition of this mixture onto gold support and the doping with Li+ ions.

Replacing lead atoms in halide perovskite materials is of significant importance for the development of environmentally friendly perovskite solar cells. In this paper, we investigated the effect of doping the MAPbI(2.6)Cl(0.4) hybrid perovskite (MA-methyl ammonium) with non-toxic elements, such as alkaline earth metal ions (Mg2+) and transition metal ions (Zn2+). The structural, morphological, and optical properties of the prepared samples were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and UV-Vis. spectroscopy. Finally, the doped films were used as photoactive layers in solar devices in order to evaluate their photovoltaic performance. Zn proved to be more appropriate to replace partially Pb and films with higher quality were obtained. As a result, the MAPb1(-x)Zn(x)I(2.6)Cl(0.4) based solar cells have demonstrated a slight improvement of the photovoltaic performances, resulting in a uniform and narrower PCEs (power conversion efficiency) range, compared to pristine MAPbI(2.6)Cl(0.4) based devices.

Protein-based particles are one of the most important research topics in nanomedicine, being used especially as drug delivery systems. From the wide variety of proteins, albumins offer several advantages in biomedical applications due to their special properties. Albumin nanoparticles play an important role as carriers in the drug delivery of chemical and biomolecular drugs, such as anticancer drugs; offer many advantages, such as biocompatibility and biodegradability; and are well-tolerated, without any side effects. In this work, various types of bovine serum albumin nanoparticles (BSA NPs), with or without ascorbic acid or glucose, were prepared via different nanoprecipitation methods. The obtained BSA NPs were characterized by UV-Vis absorption spectroscopy. Their size and morphology were studied by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). The stability in time of the developed BSA NPs was spectrally monitored. Three types of bio-entities containing BSA NPs and chlorophyll-labeled artificial cell membranes were "green" developed. The designed biohybrids were characterized by UV-Vis absorption and fluorescence emission spectroscopy, and their three-dimensional topography was investigated by AFM. Both the size and shape of the developed bio-entities were monitored through SEM analysis. These results could be exploited in the development of novel drug carrier systems or as bio-coatings to be used in the biomedical field.