NIMP| Adrian Claudiu POPA, Author at NIMP

Publications

1. Hindrances and solutions on the path towards adjoined barium titanate-hydroxyapatite ceramics with uncompromised piezoelectric and biological responses

Authors: Cioangher, M; Amarande, L; Stan, GE; Nedelcu, L; Pasuk, I; Leonat, L; Popa, AC; Miclea, LC; Savopol, T; Moisescu, MG; Tivig, I

Published: SEP 1 2024, CERAMICS INTERNATIONAL, 50, DOI: 10.1016/j.ceramint.2024.05.268

The synergistic piezoelectric and osteoconductive properties of barium titanate (BT) and hydroxyapatite (HA) could stir the development of a new generation of synthetic bone graft substitutes, with capability for rapid and safe osseointegration. The research focused on two concurrent approaches for coupling the BT and HA materials: (i) conventional sintering of BT-HA powder mixtures; and (ii) functionalization of pre-sintered BT with HA coatings using magnetron sputtering (MS). Irrespective of the BT/HA ratios ranging from 95/5 to 80/20 wt%, nanocrystalline or highly-crystallized nature of the powders, sub-micron- or micron-sized particle dimensions, and sintering temperature, it was observed that the BT-HA reactivity cannot be prevented above 800 degrees C. At higher temperatures in the range of 1000-1300 degrees C, HA undergoes decomposition and extensively reacts with BT, leading to the formation of several secondary phases such as CaTiO3, Ba2Ca(PO4)2, BaCa6(PO4)4O, BaCa(PO3)4, and beta-Ca2P2O7. As a consequence, the cytocompatibility assessed in fibroblast and osteoblast cell cultures, as well as the piezoelectric response, were significantly altered. Applying HA coatings by MS to the sintered BT ceramics successfully preserved their piezoelectric properties, while also providing an unaltered cytocompatible and osteogenic-prone surface. The HA coatings were fully crystallized at post-deposition annealing temperatures of 550 and 700 degrees C, achieving crystalline qualities comparable to HA powders sintered at 1100 and 1200 degrees C, respectively. No reactivity events between BT and HA were observed. Partial reactivity was only noticeable upon annealing at 1000 degrees C. Therefore, it is suggested that the HA coating of BT is effective in seamlessly coupling the piezoelectric and osteogenic properties of the two constituents without compromise.

2. Two decades of continuous progresses and breakthroughs in the field of bioactive ceramics and glasses driven by CICECO-hub scientists

Authors: Fernandes, HR; Kannan, S; Alam, M; Stan, GE; Popa, AC; Buczynski, R; Golebiewski, P; Ferreira, JMF

Published: OCT 2024, BIOACTIVE MATERIALS, 40, DOI: 10.1016/j.bioactmat.2024.05.041

Over the past two decades, the CICECO-hub scientists have devoted substantial efforts to advancing bioactive inorganic materials based on calcium phosphates and alkali-free bioactive glasses. A key focus has been the deliberate incorporation of therapeutic ions like Mg, Sr, Zn, Mn, or Ga to enhance osteointegration and vascularization, confer antioxidant properties, and impart antimicrobial effects, marking significant contributions to the field of biomaterials and bone tissue engineering. Such an approach is expected to circumvent the uncertainties posed by methods relying on growth factors, such as bone morphogenetic proteins, parathyroid hormone, and platelet-rich plasma, along with their associated high costs and potential adverse side effects. This comprehensive overview of CICECO-hub ' s significant contributions to the forefront inorganic biomaterials across all research aspects and dimensionalities (powders, granules, thin films, bulk materials, and porous structures), follows a unified approach rooted in a cohesive conceptual framework, including synthesis, characterization, and testing protocols. Tangible outcomes [injectable cements, durable implant coatings, and bone graft substitutes (scaffolds) featuring customized porous architectures for implant fixation, osteointegration, accelerated bone regeneration in critical-sized bone defects] were achieved. The manuscript showcases specific biofunctional examples of successful biomedical applications and effective translations to the market of bone grafts for advanced therapies.

3. Nitrogen-Doped WO₃ Nanoparticles as Electrode Materials in All-in-One Supercapacitor Devices

Authors: Ammar, AU; Popa, A; Toloman, D; Macavei, S; Ciorita, A; Bocirnea, AE; Stan, M; Erdem, E; Rostas, AM

Published: JAN 10 2024, ACS APPLIED ENGINEERING MATERIALS, 2, DOI: 10.1021/acsaenm.3c00654

The effect of the annealing temperature on 1% nitrogen-doped WO3 materials was studied, which were then used as electrode materials for high-performance supercapacitor (SC) devices. The supercapacitive performance of the proposed materials was strongly influenced by the doping element and the annealing temperature by directly changing the defect structure of the host material. The 1% N-doped WO3 materials annealed at different temperatures were thoroughly characterized through various characterization techniques, including electron paramagnetic resonance and photoluminescence spectroscopy, giving insight into the effect of N-doping on the defect structure and optical properties of WO3. When the WO3:N materials were used as electrode material in symmetric SCs, the doping element and the annealing temperature improved the electrochemical performance. No booster materials (such as carbon black) were used in the symmetric SC designs, showing increased specific capacitance (102 F/g) and energy density (14.6 W h/kg) values.

4. Multi-Parametric Exploration of a Selection of Piezoceramic Materials for Bone Graft Substitute Applications

Authors: Nedelcu, L; Ferreira, JMF; Popa, AC; Amarande, L; Nan, B; Balescu, LM; Geambasu, CD; Cioangher, MC; Leonat, L; Grigoroscuta, M; Cristea, D; Stroescu, H; Ciocoiu, RC; Stan, GE

Published: FEB 2023, MATERIALS, 16, 901, DOI: 10.3390/ma16030901

This work was devoted to the first multi-parametric unitary comparative analysis of a selection of sintered piezoceramic materials synthesised by solid-state reactions, aiming to delineate the most promising biocompatible piezoelectric material, to be further implemented into macro-porous ceramic scaffolds fabricated by 3D printing technologies. The piezoceramics under scrutiny were: KNbO3, LiNbO3, LiTaO3, BaTiO3, Zr-doped BaTiO3, and the (Ba0.85Ca0.15)(Ti0.9Zr0.1)O-3 solid solution (BCTZ). The XRD analysis revealed the high crystallinity of all sintered ceramics, while the best densification was achieved for the BaTiO3-based materials via conventional sintering. Conjunctively, BCTZ yielded the best combination of functional properties-piezoelectric response (in terms of longitudinal piezoelectric constant and planar electromechanical coupling factor) and mechanical and in vitro osteoblast cell compatibility. The selected piezoceramic was further used as a base material for the robocasting fabrication of 3D macro-porous scaffolds (porosity of similar to 50%), which yielded a promising compressive strength of similar to 20 MPa (higher than that of trabecular bone), excellent cell colonization capability, and noteworthy cytocompatibility in osteoblast cell cultures, analogous to the biological control. Thereby, good prospects for the possible development of a new generation of synthetic bone graft substitutes endowed with the piezoelectric effect as a stimulus for the enhancement of osteogenic capacity were settled.

5. Independent and complementary bio-functional effects of CuO and Ga2O3 incorporated as therapeutic agents in silica- and phosphate- based bioactive glasses

Authors: Tite, T; Popa, AC; Stuart, BW; Fernandes, HR; Chirica, IM; Lungu, GA; Macovei, D; Bartha, C; Albulescu, L; Tanase, C; Nita, S; Rusu, N; Grant, DM; Ferreira, JMF; Stan, GE

Published: JUL 2022, JOURNAL OF MATERIOMICS, 8, DOI: 10.1016/j.jmat.2021.12.009

The incorporation of therapeutic-capable ions into bioactive glasses (BGs), either based on silica (SBGs) or phosphate (PBGs), is currently envisaged as a proficient path for facilitating bone regeneration. In conjunction with this view, the single and complementary structural and bio-functional roles of CuO and Ga2O3 (in the 2-5 mol% range) were assessed, by deriving a series of SBG and PBG formulations starting from the parent glass systems, FastOs (R) BG -38.5SiO2-36.1CaO-5.6P2O5-19.2MgO-0.6CaF2, and 50.0P2O5-35.0CaO-10.0Na2O-5.0 Fe2O3 (mol%), respectively, using the process of melt-quenching. The inter-linked physico-chemistry -biological response of BGs was assessed in search of bio-functional triggers. Further light was shed on the structural role -as network former or modifier -of Cu and Ga, immersed in SBG and PBG matrices. The preliminary biological performance was surveyed in vitro by quantification of Cu and Ga ion release under homeostatic conditions, cytocompatibility assays (in fibroblast cell cultures) and antibacterial tests (against Staphylococcus aureus). The similar (Cu) and dissimilar (Ga) structural roles in the SBG and PBG vitreous networks governed their release. Namely, Cu ions were leached in similar concentrations (ranging from 10-35 ppm and 50-110 ppm at BG doses of 5 and 50 mg/mL, respectively) for both type of BGs, while the release of Ga ions was 1-2 orders of magnitude lower in the case of SBGs (i.e., 0.2-6 ppm) compared to PBGs (i.e., 9-135 ppm). This was attributed to the network modifier role of Cu in both types of BGs, and conversely, to the network former (SBGs) and network modifier (PBGs) roles of Ga. All glasses were cytocompatible at a dose of 5 mg/mL, while at the same concentration the antimicrobial efficiency was found to be accentuated by the coupled release of Cu and Ga ions from SBG. By collective assessment, the most prominent candidate material for the further development of implant coatings and bone graft substitutes was delineated as the 38.5SiO2-34.1CaO-5.6P2O5-16.2MgO-0.6CaF2-2.0CuO-3.0Ga2O3 (mol%) SBG system, which yiel-ded moderate Cu and Ga ion release, excellent cytocompatibility and marked antibacterial efficacy. (c) 2021 The Chinese Ceramic Society. Production and hosting by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).

6. New solutions for combatting implant bacterial infection based on silver nano-dispersed and gallium incorporated phosphate bioactive glass sputtered films: A preliminary study

Authors: Stuart, BW; Stan, GE; Popa, AC; Carrington, MJ; Zgura, I; Necsulescu, M; Grant, DM

Published: FEB 2022, BIOACTIVE MATERIALS, 8, DOI: 10.1016/j.bioactmat.2021.05.055

Ag/Ga were incorporated into resorbable orthopaedic phosphate bioactive glasses (PBG, containing P, Ca, Mg, Na, and Fe) thin films to demonstrate their potential to limit growth of Staphylococcus aureus and Escherichia coli in post-operative prosthetic implantation. Dual target consecutive co-sputtering was uniquely employed to produce a 46 nm Ag:PBG composite observed by high resolution TEM to consist of uniformly dispersed similar to 5 nm metallic Ag nano-particles in a glass matrix. Ga3+ was integrated into a phosphate glass preform target which was magnetron sputtered to film thicknesses of similar to 400 or 1400 nm. All coatings exhibited high surface energy of 75.4-77.3 mN/m, attributed to the presence of hydrolytic P-O-P structural surface bonds. Degradation profiles obtained in deionized water, nutrient broth and cell culture medium showed varying ion release profiles, whereby Ga release was measured in 1400 nm coating by ICP-MS to be similar to 6, 27, and 4 ppm respectively, fully dissolving by 24 h. Solubility of Ag nanoparticles was only observed in nutrient broth (similar to 9 ppm by 24 h). Quantification of colony forming units after 24 h showed encouraging antibacterial efficacy towards both S. aureus (4-log reduction for Ag:PBG and 6-log reduction for Ga-PBG approximate to 1400 nm) and E. coli (5-log reduction for all physical vapour deposited layers) strains. Human Hs27 fibroblast and mesenchymal stem cell line in vitro tests indicated good cytocompatibility for all sputtered layers, with a marginal cell proliferation inertia in the case of the Ag:PBG composite thin film. The study therefore highlights the (i) significant manufacturing development via the controlled inclusion of metallic nanoparticles into a PBG glass matrix by dual consecutive target co-sputtering and (ii) potential of PBG resorbable thin-film structures to incorporate and release cytocompatible/antibacterial oxides. Both architectures showed prospective bio-functional performance for a future generation of endo-osseous implant-type coatings.

7. Sr and Mg Doped Bi-Phasic Calcium Phosphate Macroporous Bone Graft Substitutes Fabricated by Robocasting: A Structural and Cytocompatibility Assessment

Authors: Besleaga, C; Nan, B; Popa, AC; Balescu, LM; Nedelcu, L; Neto, AS; Pasuk, I; Leonat, L; Popescu-Pelin, G; Ferreira, JMF; Stan, GE

Published: SEP 2022, JOURNAL OF FUNCTIONAL BIOMATERIALS, 13, 123, DOI: 10.3390/jfb13030123

Bi-phasic calcium phosphates (BCPs) are considered prominent candidate materials for the fabrication of bone graft substitutes. Currently, supplemental cation-doping is suggested as a powerful path to boost biofunctionality, however, there is still a lack of knowledge on the structural role of such substituents in BCPs, which in turn, could influence the intensity and extent of the biological effects. In this work, pure and Mg- and Sr-doped BCP scaffolds were fabricated by robocasting from hydrothermally synthesized powders, and then preliminarily tested in vitro and thoroughly investigated physically and chemically. Collectively, the osteoblast cell culture assays indicated that all types of BCP scaffolds (pure, Sr- or Sr-Mg-doped) delivered in vitro performances similar to the biological control, with emphasis on the Sr-Mg-doped ones. An important result was that double Mg-Sr doping obtained the ceramic with the highest beta-tricalcium phosphate (beta-TCP)/hydroxyapatite mass concentration ratio of similar to 1.8. Remarkably, Mg and Sr were found to be predominantly incorporated in the beta-TCP lattice. These findings could be important for the future development of BCP-based bone graft substitutes since the higher dissolution rate of beta-TCP enables an easier release of the therapeutic ions. This may pave the road toward medical devices with more predictable in vivo performance.

8. Phosphate bioglass thin-films: Cross-area uniformity, structure and biological performance tailored by the simple modification of magnetron sputtering gas pressure

Authors: Tite, T; Popa, AC; Chirica, IM; Stuart, BW; Galca, AC; Balescu, LM; Popescu-Pelin, G; Grant, DM; Ferreira, JMF; Stan, GE

Published: MAR 1 2021, APPLIED SURFACE SCIENCE, 541, DOI: 10.1016/j.apsusc.2020.148640

Currently, there is a considerable time-lag in the industrialisation of innovative technological solutions for the functionalization of osseous implants, with ever-demanding healthcare requirements (e.g., controlled release of therapeutic ions, match of biomaterial degradation - bone growth rates, antimicrobial efficiency). As third-generation biomaterials, phosphate bio-glasses (PBGs) have demonstrated an ability to stimulate specific biological responses from tissue to molecular level, by successfully coupling bioactive and resorbable material properties. Here, radio-frequency magnetron sputtered (RF-MS) PBGs were explored as sacrificial resorbable layers for prospective biomedical implant designs. A PBG powder with a 50-P2O5, 35-CaO, 10-Na2O and 5-Fe2O3 composition (mol%) was used as source (target) material. The influence of the argon working pressure (0.2-1 Pa) - one of the most prominent RF-MS variables - on the morphology, structure, uniformity, composition, degradation rate and cytocompatibility of PBG films was investigated. The engineered modification of physical-chemical and biological features of the PBG sputtered films was multi-parametrically surveyed by AFM, EDXS, spectroscopic ellipsometry, GIXRD, FTIR spectroscopy measurements and in vitro assays. Results suggested that the film thickness, composition, density and structure were preserved over a uniformity region having a diameter of similar to 30 mm, irrespective of sputtering pressure. The network connectivity and the surface porosity of the films were found to have antagonistic roles with respect to the in vitro degradation performance. The possibility of fine tuning the composition, structure and thereby biological interaction of the PBG films by conveniently modifying the sputtering pressure was shown (i.e., permitting their complete controlled degradation, without cytotoxic effects). This work is the first to show in vitro cytocompatibility outcomes of sputtered PBG films and their cross-area uniformity, and thus, it could prove to be an important technological step in their future biomedical application and suggest implications for future industrial scale-up.

9. The Physico-Chemical Properties and Exploratory Real-Time Cell Analysis of Hydroxyapatite Nanopowders Substituted with Ce, Mg, Sr, and Zn (0.5-5 at.%)

Authors: Chirica, IM; Enciu, AM; Tite, T; Dudau, M; Albulescu, L; Iconaru, SL; Predoi, D; Pasuk, I; Enculescu, M; Radu, C; Mihalcea, CG; Popa, AC; Rusu, N; Nita, S; Tanase, C; Stan, GE

Published: JUL 2021, MATERIALS, 14, DOI: 10.3390/ma14143808

Cation-substituted hydroxyapatite (HA), standalone or as a composite (blended with polymers or metals), is currently regarded as a noteworthy candidate material for bone repair/regeneration either in the form of powders, porous scaffolds or coatings for endo-osseous dental and orthopaedic implants. As a response to the numerous contradictions reported in literature, this work presents, in one study, the physico-chemical properties and the cytocompatibility response of single cation-doped (Ce, Mg, Sr or Zn) HA nanopowders in a wide concentration range (0.5-5 at.%). The modification of composition, morphology, and structure was multiparametrically monitored via energy dispersive X-ray, X-ray photoelectron, Fourier-transform infrared and micro-Raman spectroscopy methods, as well as by transmission electron microscopy and X-ray diffraction. From a compositional point of view, Ce and Sr were well-incorporated in HA, while slight and pronounced deviations were observed for Mg and Zn, respectively. The change of the lattice parameters, crystallite size, and substituting cation occupation factors either in the Ca(I) or Ca(II) sites were further determined. Sr produced the most important HA structural changes. The in vitro biological performance was evaluated by the (i) determination of leached therapeutic cations (by inductively coupled plasma mass spectrometry) and (ii) assessment of cell behaviour by both conventional assays (e.g., proliferation-3-(4,5-dimethyl thiazol-2-yl) 5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium assay; cytotoxicity-lactate dehydrogenase release assay) and, for the first time, real-time cell analysis (RTCA). Three cell lines were employed: fibroblast, osteoblast, and endothelial. When monophasic, the substituted HA supported the cells' viability and proliferation without signs of toxicity. The RTCA results indicate the excellent adherence of cells. The study strived to offer a perspective on the behaviour of Ce-, Mg-, Sr-, or Zn-substituted HAs and to deliver a well-encompassing viewpoint on their effects. This can be highly important for the future development of such bioceramics, paving the road toward the identification of candidates with highly promising therapeutic effects.

10. The Beneficial Mechanical and Biological Outcomes of Thin Copper-Gallium Doped Silica-Rich Bio-Active Glass Implant-Type Coatings

Authors: Stan, GE; Tite, T; Popa, AC; Chirica, IM; Negrila, CC; Besleaga, C; Zgura, I; Sergentu, AC; Popescu-Pelin, G; Cristea, D; Ionescu, LE; Necsulescu, M; Fernandes, HR; Ferreira, JMF

Published: NOV 2020, COATINGS, 10, DOI: 10.3390/coatings10111119

Silica-based bioactive glasses (SBG) hold great promise as bio-functional coatings of metallic endo-osseous implants, due to their osteoproductive potential, and, in the case of designed formulations, suitable mechanical properties and antibacterial efficacy. In the framework of this study, the FastOs(R)BG alkali-free SBG system (mol%: SiO2-38.49, CaO-36.07, P2O5-5.61, MgO-19.24, CaF2-0.59), with CuO (2 mol%) and Ga2O3 (3 mol%) antimicrobial agents, partially substituting in the parent system CaO and MgO, respectively, was used as source material for the fabrication of intentionally silica-enriched implant-type thin coatings (similar to 600 nm) onto titanium (Ti) substrates by radio-frequency magnetron sputtering. The physico-chemical and mechanical characteristics, as well as the in vitro preliminary cytocompatibility and antibacterial performance of an alkali-free silica-rich bio-active glass coating designs was further explored. The films were smooth (R-RMS < 1 nm) and hydrophilic (water contact angle of similar to 65 degrees). The SBG coatings deposited from alkali-free copper-gallium co-doped FastOs(R)BG-derived exhibited improved wear performance, with the coatings eliciting a bonding strength value of similar to 53 MPa, Lc3 critical load value of similar to 4.9 N, hardness of similar to 6.1 GPa and an elastic modulus of similar to 127 GPa. The Cu and Ga co-doped SBG layers had excellent cytocompatibility, while reducing after 24 h the Staphylococcus aureus bacterial development with 4 orders of magnitude with respect to the control situations (i.e., nutritive broth and Ti substrate). Thereby, such SBG constructs could pave the road towards high-performance bio-functional coatings with excellent mechanical properties and enhanced biological features (e.g., by coupling cytocompatibility with antimicrobial properties), which are in great demand nowadays.

11. Antibacterial efficiency of alkali-free bio-glasses incorporating ZnO and/or SrO as therapeutic agents

Authors: Popa, AC; Fernandes, HR; Necsulescu, M; Luculescu, C; Cioangher, M; Dumitru, V; Stuart, BW; Grant, DM; Ferreira, JMF; Stan, GE

Published: MAR 2019, CERAMICS INTERNATIONAL, 45, 4380, DOI: 10.1016/j.ceramint.2018.11.112

A series of seven alkali-free silica-based bioactive glasses (SBG) with ZnO and/or SrO additives (in concentrations of 0-12 mol%) were synthesized by melt-quenching, aiming to delineate a candidate formulation possessing (i) a coefficient of thermal expansion (CTE) similar to the one of titanium (Ti) and its medical grade super alloys (crucial for the future development of mechanically adherent implant-type SBG coatings) and (ii) antibacterial efficiency, while (iii) conserving a good cytocompatibility. The SBGs powders were multi-parametrically evaluated by X-ray diffraction, Fourier transform infrared and micro-Raman spectroscopy, dilatometry, inductively coupled plasma mass spectrometry, antibacterial (against Staphylococcus aureus and Escherichia coli strains) suspension inhibition and agar diffusion tests, and human mesenchymal stem cells cytocompatibility assays. The results showed that the coupled incorporation of zinc and strontium ions into the parent glass composition has a combinatorial and additive benefit. In particular, the "Z6S4" formulation (mol%: SiO2-38.49, CaO-32.07, P2O5-5.61, MgO-13.24, CaF2-0.59, ZnO-6.0, SrO-4.0) conferred strong antimicrobial activity against both types of strains, minimal cytotoxicity combined with good stem cells viability and proliferation, and a CTE (similar to 8.7 x 10(-6) x degrees C-1) matching well those of the Ti-based implant materials.

12. Animal Origin Bioactive Hydroxyapatite Thin Films Synthesized by RF-Magnetron Sputtering on 3D Printed Cranial Implants

Authors: Chioibasu, D; Duta, L; Popescu-Pelin, G; Popa, N; Milodin, N; Iosub, S; Balescu, LM; Galca, AC; Popa, AC; Oktar, FN; Stan, GE; Popescu, AC

Published: DEC 2019, METALS, 9, DOI: 10.3390/met9121332

Ti6Al4V cranial prostheses in the form of patterned meshes were 3D printed by selective laser melting in an argon environment; using a CO2 laser source and micron-sized Ti6Al4V powder as the starting material. The size and shape of prostheses were chosen based on actual computer tomography images of patient skull fractures supplied in the framework of a collaboration with a neurosurgery clinic. After optimizations of scanning speed and laser parameters, the printed material was defect-free (as shown by metallographic analyses) and chemically homogeneous, without elemental segregation or depletion. The prostheses were coated by radio-frequency magnetron sputtering (RF-MS) with a bioactive thin layer of hydroxyapatite using a bioceramic powder derived from biogenic resources (Bio-HA). Initially amorphous, the films were converted to fully-crystalline form by applying a post-deposition thermal-treatment at 500 degrees C/1 h in air. The X-ray diffraction structural investigations indicated the phase purity of the deposited films composed solely of a hexagonal hydroxyapatite-like compound. On the other hand, the Fourier transform infrared spectroscopic investigations revealed that the biological carbonatation of the bone mineral phase was well-replicated in the case of crystallized Bio-HA RF-MS implant coatings. The in vitro acellular assays, performed in both the fully inorganic Kokubo's simulated body fluid and the biomimetic organic-inorganic McCoy's 5A cell culture medium up to 21 days, emphasized both the good resistance to degradation and the biomineralization capacity of the films. Further in vitro tests conducted in SaOs-2 osteoblast-like cells showed a positive proliferation rate on the Bio-HA RF-MS coating along with a good adhesion developed on the biomaterial surface by elongated membrane protrusions.

13. Comprehensive In Vitro Testing of Calcium Phosphate-Based Bioceramics with Orthopedic and Dentistry Applications

Authors: Albulescu, R; Popa, AC; Enciu, AM; Albulescu, L; Dudau, M; Popescu, ID; Mihai, S; Codrici, E; Pop, S; Lupu, AR; Stan, GE; Manda, G; Tanase, C

Published: NOV 2 2019, MATERIALS, 12, DOI: 10.3390/ma12223704

Recently, a large spectrum of biomaterials emerged, with emphasis on various pure, blended, or doped calcium phosphates (CaPs). Although basic cytocompatibility testing protocols are referred by International Organization for Standardization (ISO) 10993 (parts 1-22), rigorous in vitro testing using cutting-edge technologies should be carried out in order to fully understand the behavior of various biomaterials (whether in bulk or low-dimensional object form) and to better gauge their outcome when implanted. In this review, current molecular techniques are assessed for the in-depth characterization of angiogenic potential, osteogenic capability, and the modulation of oxidative stress and inflammation properties of CaPs and their cation- and/or anion-substituted derivatives. Using such techniques, mechanisms of action of these compounds can be deciphered, highlighting the signaling pathway activation, cross-talk, and modulation by microRNA expression, which in turn can safely pave the road toward a better filtering of the truly functional, application-ready innovative therapeutic bioceramic-based solutions.

14. Cationic Substitutions in Hydroxyapatite: Current Status of the Derived Biofunctional Effects and Their In Vitro Interrogation Methods

Authors: Tite, T; Popa, AC; Balescu, LM; Bogdan, IM; Pasuk, I; Ferreira, JMF; Stan, GE

Published: NOV 2018, MATERIALS, 11, DOI: 10.3390/ma11112081

High-performance bioceramics are required for preventing failure and prolonging the life-time of bone grafting scaffolds and osseous implants. The proper identification and development of materials with extended functionalities addressing socio-economic needs and health problems constitute important and critical steps at the heart of clinical research. Recent findings in the realm of ion-substituted hydroxyapatite (HA) could pave the road towards significant developments in biomedicine, with an emphasis on a new generation of orthopaedic and dentistry applications, since such bioceramics are able to mimic the structural, compositional and mechanical properties of the bone mineral phase. In fact, the fascinating ability of the HA crystalline lattice to allow for the substitution of calcium ions with a plethora of cationic species has been widely explored in the recent period, with consequent modifications of its physical and chemical features, as well as its functional mechanical and in vitro and in vivo biological performance. A comprehensive inventory of the progresses achieved so far is both opportune and of paramount importance, in order to not only gather and summarize information, but to also allow fellow researchers to compare with ease and filter the best solutions for the cation substitution of HA-based materials and enable the development of multi-functional biomedical designs. The review surveys preparation and synthesis methods, pinpoints all the explored cation dopants, and discloses the full application range of substituted HA. Special attention is dedicated to the antimicrobial efficiency spectrum and cytotoxic trade-off concentration values for various cell lines, highlighting new prophylactic routes for the prevention of implant failure. Importantly, the current in vitro biological tests (widely employed to unveil the biological performance of HA-based materials), and their ability to mimic the in vivo biological interactions, are also critically assessed. Future perspectives are discussed, and a series of recommendations are underlined.

15. Gallium incorporation into phosphate based glasses: Bulk and thin film properties

Authors: Stuart, BW; Grant, CA; Stan, GE; Popa, AC; Titman, JJ; Grant, DM

Published: JUN 2018, JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS, 82, 382, DOI: 10.1016/j.jmbbm.2018.03.041

The osteogenic ions Ca2+ P5+, Mg2+, and antimicrobial ion Ga3+ were homogenously dispersed into a 1.45 mu m thick phosphate glass coating by plasma assisted sputtering onto commercially pure grade titanium. The objective was to deliver therapeutic ions in orthopaedic/dental implants such as cementeless endoprostheses or dental screws. The hardness 4.7 GPa and elastic modulus 69.7 GPa, of the coating were comparable to plasma sprayed hydroxyapatite/dental enamel, whilst superseding femoral cortical bone. To investigate the manufacturing challenge of translation from a target to vapour condensed coating, structural/compositional properties of the target (P51MQ) were compared to the coating (P40PVD) and a melt-quenched equivalent (P40MQ). Following condensation from P51MQ to P40PVD, P2O5 content reduced from 48.9 to 40.5 mol%. This depoly-merisation and reduction in the P-O-P bridging oxygen content as determined by P-31 NMR, FTIR and Raman spectroscopy techniques was attributed to a decrease in the P2O5 network former and increases in alkali/alkali-earth cations. P40PVD appeared denser (3.47 vs. 2.70 g cm(-3)) and more polymerised than it's compositionally equivalent P40MQ, showing that structure/ mechanical properties were affected by manufacturing route.

16. Bioglass implant-coating interactions in synthetic physiological fluids with varying degrees of biomimicry

Authors: Popa, AC; Stan, GE; Husanu, MA; Mercioniu, I; Santos, LF; Fernandes, HR; Ferreira, JMF

Published: 2017, INTERNATIONAL JOURNAL OF NANOMEDICINE, 12, 707, DOI: 10.2147/IJN.S123236

Synthetic physiological fluids are currently used as a first in vitro bioactivity assessment for bone grafts. Our understanding about the interactions taking place at the fluid-implant interface has evolved remarkably during the last decade, and does not comply with the traditional International Organization for Standardization/final draft International Standard 23317 protocol in purely inorganic simulated body fluid. The advances in our knowledge point to the need of a true paradigm shift toward testing physiological fluids with enhanced biomimicry and a better understanding of the materials' structure-dissolution behavior. This will contribute to "upgrade" our vision of entire cascades of events taking place at the implant surfaces upon immersion in the testing media or after implantation. Starting from an osteoinductive bioglass composition with the ability to alleviate the oxidative stress, thin bioglass films with different degrees of polymerization were deposited onto titanium substrates. Their biomineralization activity in simulated body fluid and in a series of new inorganic-organic media with increasing biomimicry that more closely simulated the human intercellular environment was compared. A comprehensive range of advanced characterization tools (scanning electron microscopy; grazing-incidence X-ray diffraction; Fourier-transform infrared, micro-Raman, energy-dispersive, X-ray photoelectron, and surface-enhanced laser desorption/ionization time-of-flight mass spectroscopies; and cytocompatibility assays using mesenchymal stem cells) were used. The information gathered is very useful to biologists, biophysicists, clinicians, and material scientists with special interest in teaching and research. By combining all the analyses, we propose herein a step forward toward establishing an improved unified protocol for testing the bioactivity of implant materials.

17. Comparative physical, chemical and biological assessment of simple and titanium-doped ovine dentine-derived hydroxyapatite coatings fabricated by pulsed laser deposition

Authors: Duta, L; Mihailescu, N; Popescu, AC; Luculescu, CR; Mihailescu, IN; Cetin, G; Gunduz, O; Oktar, FN; Popa, AC; Kuncser, A; Besleaga, C; Stan, GE

Published: AUG 15 2017, APPLIED SURFACE SCIENCE, 413, 139, DOI: 10.1016/j.apsusc.2017.04.025

We report on the synthesis by Pulsed Laser Deposition of simple and Ti doped hydroxyapatite thin films of biological (ovine dentine) origin. Detailed physical, chemical, mechanical and biological investigations were performed. Morphological examination of films showed a surface composed of spheroidal particulates, of micronic size. Compositional analyses pointed to the presence of typical natural doping elements of bone, along with a slight non-stoichiometry of the deposited films. Structural investigations proved the monophasic hydroxyapatite nature of both simple and Ti doped films. Ti doping of biological hydroxyapatite induced an overall downgrade of the films crystallinity together with an increase of the films roughness. It is to be emphasized that bonding strength values measured at film. Ti substrate interface were superior to the minimum value imposed by International Standards regulating the load-bearing implant coatings. In vitro tests on Ti doped structures, compared to simple ones, revealed excellent biocompatibility in human mesenchymal stem cell cultures, a higher proliferation rate and a good cytocompatibility. The obtained results aim to elucidate the overall positive role of Ti doping on the hydroxyapatite films performance, and demonstrate the possibility to use this novel type of coatings as feasible materials for future implantology applications. (C) 2017 Elsevier B.V. All rights reserved.

18. Mechanical, Corrosion and Biological Properties of Room-Temperature Sputtered Aluminum Nitride Films with Dissimilar Nanostructure

Authors: Besleaga, C; Dumitru, V; Trinca, LM; Popa, AC; Negrila, CC; Kolodziejczyk, L; Luculescu, CR; Ionescu, GC; Ripeanu, RG; Vladescu, A; Stan, GE

Published: NOV 2017, NANOMATERIALS, 7, DOI: 10.3390/nano7110394

Aluminum Nitride (AlN) has been long time being regarded as highly interesting material for developing sensing applications (including biosensors and implantable sensors). AlN, due to its appealing electronic properties, is envisaged lately to serve as a multi-functional biosensing platform. Although generally exploited for its intrinsic piezoelectricity, its surface morphology and mechanical performance (elastic modulus, hardness, wear, scratch and tensile resistance to delamination, adherence to the substrate), corrosion resistance and cytocompatibility are also essential features for high performance sustainable biosensor devices. However, information about AlN suitability for such applications is rather scarce or at best scattered and incomplete. Here, we aim to deliver a comprehensive evaluation of the morpho-structural, compositional, mechanical, electrochemical and biological properties of reactive radio-frequency magnetron sputtered AlN nanostructured thin films with various degrees of c-axis texturing, deposited at a low temperature (similar to 50 degrees C) on Si (100) substrates. The inter-conditionality elicited between the base pressure level attained in the reactor chamber and crystalline quality of AlN films is highlighted. The potential suitability of nanostructured AlN (in form of thin films) for the realization of various type of sensors (with emphasis on bio-sensors) is thoroughly probed, thus unveiling its advantages and limitations, as well as suggesting paths to safely exploit the remarkable prospects of this type of materials.

19. Submicrometer Hollow Bioglass Cones Deposited by Radio Frequency Magnetron Sputtering: Formation Mechanism, Properties, and Prospective Biomedical Applications

Authors: Popa, AC; Stan, GE; Besleaga, C; Ion, L; Maraloiu, VA; Tulyaganov, DU; Ferreira, JMF

Published: FEB 24 2016, ACS APPLIED MATERIALS & INTERFACES, 8, 4367, DOI: 10.1021/acsami.6b00606

This work reports on the unprecedented magnetron sputtering deposition of submicrometric hollow cones of bioactive glass at low temperature in the absence of any template or catalyst. The influence of sputtering conditions on the formation and development of bioglass cones was studied. It was shown that larger populations of well-developed cones could be achieved by increasing the argon sputtering pressure. A mechanism describing the growth of bioglass hollow cones is presented, offering the links for process control and reproducibility of the cone features. The composition, structure, and morphology of the as-synthesized hollow cones were investigated by energy dispersive spectroscopy (EDS), Fourier transform infrared spectroscopy (FTIR), grazing incidence geometry X-ray diffraction (GIXRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM)-selected area electron diffraction (SAED). The in vitro biological performance, assessed by degradation tests (ISO 10993-14) and cytocompatibility assays (ISO 10993-5) in endothelial cell cultures, was excellent. This allied with resorbability and the unique morphological features make the submicrometer hollow cones interesting candidate material devices for focal transitory permeabilization of the blood brain barrier in the treatment of carcinoma and neurodegenerative disorders.

20. Thickness Influence on In Vitro Biocompatibility of Titanium Nitride Thin Films Synthesized by Pulsed Laser Deposition

Authors: Duta, L; Stan, GE; Popa, AC; Husanu, MA; Moga, S; Socol, M; Zgura, I; Miculescu, F; Urzica, I; Popescu, AC; Mihailescu, IN

Published: JAN 2016, MATERIALS, 9, DOI: 10.3390/ma9010038

We report a study on the biocompatibility vs. thickness in the case of titanium nitride (TiN) films synthesized on 410 medical grade stainless steel substrates by pulsed laser deposition. The films were grown in a nitrogen atmosphere, and their in vitro cytotoxicity was assessed according to ISO 10993-5 [1]. Extensive physical-chemical analyses have been carried out on the deposited structures with various thicknesses in order to explain the differences in biological behavior: profilometry, scanning electron microscopy, atomic force microscopy, X-ray photoelectron spectroscopy (XPS), X-ray diffraction and surface energy measurements. XPS revealed the presence of titanium oxynitride beside TiN in amounts that vary with the film thickness. The cytocompatibility of films seems to be influenced by their TiN surface content. The thinner films seem to be more suitable for medical applications, due to the combined high values of bonding strength and superior cytocompatibility.

21. Structural and biological evaluation of lignin addition to simple and silver-doped hydroxyapatite thin films synthesized by matrix-assisted pulsed laser evaporation

Authors: Jankovic, A; Erakovic, S; Ristoscu, C; Mihailescu, N; Duta, L; Visan, A; Stan, GE; Popa, AC; Husanu, MA; Luculescu, CR; Srdic, VV; Janackovic, D; Miskovic-Stankovic, V; Bleotu, C; Chifiriuc, MC; Mihailescu, IN

Published: JAN 2015, JOURNAL OF MATERIALS SCIENCE-MATERIALS IN MEDICINE, 26, DOI: 10.1007/s10856-014-5333-y

We report on thin film deposition by matrix-assisted pulsed laser evaporation of simple hydroxyapatite (HA) or silver (Ag) doped HA combined with the natural biopolymer organosolv lignin (Lig) (Ag:HA-Lig). Solid cryogenic target of aqueous dispersions of Ag:HA-Lig composite and its counterpart without silver (HA-Lig) were prepared for evaporation using a KrF* excimer laser source. The expulsed material was assembled onto TiO2/Ti substrata or silicon wafers and subjected to physical-chemical investigations. Smooth, uniform films adherent to substratum were observed. The chemical analyses confirmed the presence of the HA components, but also evidenced traces of Ag and Lig. Deposited HA was Ca deficient, which is indicative of a film with increased solubility. Recorded X-ray Diffraction patterns were characteristic for amorphous films. Lig presence in thin films was undoubtedly proved by both X-ray Photoelectron and Fourier Transform Infra-Red Spectroscopy analyses. The microbiological evaluation showed that the newly assembled surfaces exhibited an inhibitory activity both on the initial steps of biofilm forming, and on mature bacterial and fungal biofilm development. The intensity of the antibiofilm activity was positively influenced by the presence of the Lig and/or Ag, in the case of Staphylococcus aureus, Pseudomonas aeruginosa and Candida famata biofilms. The obtained surfaces exhibited a low cytotoxicity toward human mesenchymal stem cells, being therefore promising candidates for fabricating implantable biomaterials with increased biocompatibility and resistance to microbial colonization and further biofilm development.

22. Superior biofunctionality of dental implant fixtures uniformly coated with durable bioglass films by magnetron sputtering

Authors: Popa, AC; Stan, GE; Enculescu, M; Tanase, C; Tulyaganov, DU; Ferreira, JMF

Published: NOV 2015, JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS, 51, 327, DOI: 10.1016/j.jmbbm.2015.07.028

Bioactive glasses are currently considered the suitable candidates to stir the quest for a new generation of osseous implants with superior biological/functional performance. In congruence with this vision, this contribution aims to introduce a reliable technological recipe for coating fairly complex 3D-shaped implants (e.g. dental screws) with uniform and mechanical resistant bioactive glass films by the radio-frequency magnetron sputtering method. The mechanical reliability of the bioactive glass films applied to real Ti dental implant fixtures has been evaluated by a procedure comprised of "cold" implantation in pig mandibular bone from a dead animal, followed by immediate tension-free extraction tests. The effects of the complex mechanical strains occurring during implantation were analysed by scanning electron microscopy coupled with electron dispersive spectroscopy. Extensive biocompatibility assays (MTS, immunofluorescence, Western blot) revealed that the bioactive glass films stimulated strong cellular adhesion and proliferation of human dental pulp stem cells, without promoting their differentiation. The ability of the implant coatings to conserve a healthy stem cell pool is promising to further endorse the fabrication of new osseointegration implant designs with extended lifetime. (C) 2015 Elsevier Ltd. All rights reserved.

23. Nanomechanical characterization of bioglass films synthesized by magnetron sputtering

Authors: Popa, AC; Marques, VMF; Stan, GE; Husanu, MA; Galca, AC; Ghica, C; Tulyaganov, DU; Lemos, AF; Ferreira, JMF

Published: FEB 28 2014, THIN SOLID FILMS, 553, 172, DOI: 10.1016/j.tsf.2013.10.104

Bioactive glasses are osteoproductive-type inorganic materials possessing the highest indices of bioactivity in both bulk and thin film forms. The prerequisites for reliable implant-type coatings are both their biological and mechanical performances. Whilst the bioglass films' structural, chemical and biological properties have been studied extensively, information about their mechanical performance is scarce. Here, transmission electron microscopy, energy dispersive X-ray spectroscopy, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, nanoindentation and pull-out measurements were employed to assess the morphological, chemical, structural and mechanical properties of the bioglass films deposited onto Ti substrates by radio-frequency magnetron sputtering (RF-MS). The biological safety of the thin bioglass films was evaluated preliminarily in vitro by investigating the adherence, proliferation and cytotoxicity of fibroblast cells cultivated on their surface. Our study emphasize the versatility of RF-MS, showing how bioglass films' features such as composition, structure, bonding strength, hardness, elastic modulus and biological response can be conveniently adapted by tuning the RF-MS working conditions, and therefore demonstrating the unexplored potential of this deposition technique for preparing quality biomimetic glass coatings. (C) 2013 Elsevier B. V. All rights reserved.

24. ULTRA HIGH MOLECULAR WEIGHT POLYETHYLENE ACETABULAR CUPS FUNCTIONALIZED WITH BIOACTIVE GLASS COATINGS SYNTHESIZED BY PULSED LASER DEPOSITION

Authors: Duta, L; Popa, AC; Miculescu, F; Mihailescu, IN

Published: 2014, ROMANIAN REPORTS IN PHYSICS, 66, 800, DOI:

We report on the synthesis by PLD of bioactive glass (BG) films onto ultra high molecular weight polyethylene acetabular cups, and their preliminarily characterization after immersion in simulated body fluid. Fourier Transform Infrared spectra evidenced the strong depolymerization of the BG coatings. Scanning Electron Microscopy evidenced that the typical PLD film surface was converted after soaking in SBF to a rough one consisting of acicular crystals. Energy Dispersive Spectroscopy analysis demonstrated a remarkable conservation of the targets stoichiometry. The functionalization of acetabular cups with BG films by PLD should allow for the fabrication of implant coatings with improved osteoinductive characteristics.

25. Strong bonding between sputtered bioglass-ceramic films and Ti-substrate implants induced by atomic inter-diffusion post-deposition heat-treatments

Authors: Stan, GE; Popa, AC; Galca, AC; Aldica, G; Ferreira, JMF

Published: SEP 1 2013, APPLIED SURFACE SCIENCE, 280, 538, DOI: 10.1016/j.apsusc.2013.05.022

Bioglasses (BG) are the inorganic materials exhibiting the highest indices of bioactivity. Their appliance as films for bio-functionalization of metallic implant surfaces has been regarded as an optimal solution for surpassing their limited bulk mechanical properties. This study reports on magnetron sputtering of alkali-free BG thin films by varying the target-to-substrate working distance, which proved to play an important role in determining the films' properties. Post deposition heat-treatments at temperatures slightly above the glass transformation temperature were then applied to induce inter-diffusion processes at the BG/titanium substrate interface and strengthening the bonding as determined by pull-out adherence measurements. The morphological and structural features assessed by SEM-EDS, XRD, and FTIR revealed a good correlation between the formations of inter-metallic titanium silicide phases and the films' bonding strength. The highest mean value of pull-out adherence (60.3 +/- 4.6 MPa), which is adequate even for load-bearing biomedical applications, was recorded for films deposited at a working distance of 35 mm followed by a heat-treatment at 750 degrees C for 2 h in air. The experimental findings are explained on the basis of structural, compositional and thermodynamic considerations. (C) 2013 Elsevier B.V. All rights reserved.

26. Multi-layer haemocompatible diamond-like carbon coatings obtained by combined radio frequency plasma enhanced chemical vapor deposition and magnetron sputtering

Authors: Popa, AC; Stan, GE; Husanu, MA; Pasuk, I; Popescu, ID; Popescu, AC; Mihailescu, IN

Published: DEC 2013, JOURNAL OF MATERIALS SCIENCE-MATERIALS IN MEDICINE, 24, 2707, DOI: 10.1007/s10856-013-5026-y

Radio-frequency Plasma Enhanced Chemical Vapour Deposition (in different methane dilutions) was used to synthesize adherent and haemocompatible diamond-like carbon (DLC) films on medical grade titanium substrates. The improvement of the adherence has been achieved by interposing a functional buffer layer with graded composition TixTiC1-x (x = 0-1) synthesized by magnetron co-sputtering. Bonding strength values of up to similar to 67 MPa have been measured by pull-out tests. Films with different sp(3)/sp(2) ratio have been obtained by changing the methane concentration in the deposition chamber. Raman spectroscopy, X-ray photoelectron spectroscopy and X-ray diffraction were employed for the physical-chemical characterization of the samples. The highest concentration of sp(3)-C (similar to 87 %), corresponding to a lower DLC surface energy (28.7 mJ/m(2) ), was deposited in a pure methane atmosphere. The biological response of the DLC films was assayed by a state-of-the-art biological analysis method (surface enhanced laser desorption/ionization-time of flight mass spectroscopy), in conjunction with other dedicated testing techniques: Western blot and partial thromboplastin time. The data support a cause-effect relationship between sp(3)-C content, surface energy and coagulation time, as well as between platelet-surface adherence properties and protein adsorption profiles.

27. BIOREACTIVITY EVALUATION IN SIMULATED BODY FLUID OF MAGNETRON SPUTTERED GLASS AND GLASS-CERAMIC COATINGS: A FTIR SPECTROSCOPY STUDY

Authors: Stan, GE; Popa, AC; Bojin, D

Published: APR-JUN 2010, DIGEST JOURNAL OF NANOMATERIALS AND BIOSTRUCTURES, 5, 566, DOI:

In this study, Fourier Transform Infrared Spectroscopy (FTIR) in Attenuated Total Reflectance mode was employed as main characterization technique to investigate the reaction mechanisms in vitro (SBF) of bioglass and glass-ceramic sputtered coatings. Two bioglass compositional systems are compared in order to gain more information regarding their in vitro bioreactivity. Important correlations between the concentration of non-bridging silicon-oxygen (Si-O-NBO) groups and the content of network modifiers were found. FTIR revealed that the high concentrations of Si-O-NBO groups are promoting the enhancing of coatings' reactivity. This information could be very useful for the development and tailoring of new bioactive glasses with an optimum biological behaviour. By varying the compositional features and the structural state, the sputtered glassy coatings exhibited different in vitro behaviour: inertness, resorbability and bioactivity.

28. POLYMER-LIKE AND DIAMOND-LIKE CARBON COATINGS PREPARED BY RF-PECVD FOR BIOMEDICAL APPLICATIONS

Authors: Stan, GE; Marcov, DA; Popa, AC; Husanu, MA

Published: JUL-SEP 2010, DIGEST JOURNAL OF NANOMATERIALS AND BIOSTRUCTURES, 5, 718, DOI:

Hydrogenated amorphous carbon (a-C: H) films were grown by radio-frequency (1.78 MHz) plasma enhanced chemical vapour deposition technique onto medical grade Ti6Al4V substrates. By varying the deposition pressure (13.33 Pa and 53.33 Pa, respectively) and methane dilution (20% and 60%, respectively) several types of carbonic films were obtained, presenting different bonding structures, surface energies and morphological features reflected in their biological behaviour. FTIR, Raman, UV-Vis, XPS and AFM measurements were used for characterizing these structures. The surface energy was determined by contact angle measurements, and their thrombogenicity was tested by the activated partial thromboplastin time (aPTT) method. We have noticed that at the same values of methane in argon dilution but at different pressure values, the film structure was totally changed: soft polymer-like carbon (PLC) type at the higher pressure and hard diamond-like carbon (DLC) type at the lower pressure. Raman spectroscopy and XPS suggested that the highest sp(3) ratio (similar to 52%), was found for DLC films prepared in a 60% methane dilution in argon. It has been found that for both PLC and DLC structures the surface energy has a decreasing tendency with the methane concentration increase in the deposition atmosphere. Excellent aPTT results were obtained for the DLC-60 (18.6.+/- 0.3 min) and PLC-20 (17.4 +/- 0.5 min) structures, superior to those recorded for Ti6Al4V and PMMA commercial materials. These values recommend the prepared carbonic structures for medical applications: harder coatings (DLC) for metal prostheses (heart valves, acetabular cups etc.), while softer and flexible coatings (PLC) for the textile vessels or stents biofunctionalization.

29. Polaron activation energy as evidenced by EMR in colossal magnetoresistive nanowires

Authors: Popa, A; Toloman, D; Grecu, MN; Mihailescu, G; Darabont, A; Pop, CVL; Raita, O; Fardis, M; Idziak, S; Hoffmann, SK; Giurgiu, LM

Published: JUL 2008, APPLIED MAGNETIC RESONANCE, 34, 26, DOI: 10.1007/s00723-008-0097-5

In the present work an X-band electron magnetic resonance (EMR) investigation in the paramagnetic regime of colossal magnetoresistive manganite La2/3Ca1/3 MnO3 (LCMO) nanowires was carried out. The temperature dependence of the EMR line width has been analyzed in terms of the small polaron hopping scenario. From this analysis, the polaron activation energy E-a in LCMO nanowires was evaluated. A discussion is given concerning the factors which could explain the smaller value of E-a as compared with the corresponding ones for LCMO nanoparticles.

30. Synthesis and electron spin resonance of La2/3Ca1/3MnO3 nanowires

Authors: Toloman, D; Mihailescu, G; Darabont, A; Pop, CVL; Olenic, L; Popa, A; Raita, O; Jivanescu, M; Grecu, MN; Giurgiu, LM; Idziak, S; Hoffmann, SK

Published: APR 2006, JOURNAL OF OPTOELECTRONICS AND ADVANCED MATERIALS, 8, 469, DOI:

La2/3Ca1/3MnO3 (LCMO) nanowires were prepared using a sol-gel process and an anodically oxidized aluminum template. Scanning electron microscopy (SEM) shows that the nanowires are almost parallel and their diameter is around 40 nm. The temperature dependence of the electron spin resonance (ESR) linewidth is similar to that observed for the case of nanostructured LCMO. From this dependence, the determined magnetic transition temperature, T-C, of the LCMO nanowires, is of the order of 120-130 K.

31. Crystallite size effect in PbS thin films grown on glass substrates by chemical bath deposition

Authors: Popa, A; Lisca, M; Stancu, V; Buda, M; Pentia, E; Botila, T

Published: FEB 2006, JOURNAL OF OPTOELECTRONICS AND ADVANCED MATERIALS, 8, 45, DOI:

Nanocrystalline PbS thin films were grown on glass substrates using Chemical Bath Deposition (CBD) method. The presence of nanocrystals was revealed by optical absorption and photocurrent measurements. We have compared the absorption threshold between large size and nanocrystalline PbS. Our study was performed in order to demonstrate that the size of the PbS thin films crystallites affects the photoelectric properties of the material. Using the Scanning Electron Microscopy (SEM) we have determined that the grains inside large size PbS crystallites are 300 nm. From the optical absorption measurements we have determined that the size of PbS nanocrystals is between 5-50 nm. The photoconduction measurements show that large size PbS has a maximum in infrared situated at 2.4 mu m, and in PbS nanocrystalline thin film this maximum is shifted toward smaller wavelengths towards visible and near infrared.

32. Electrical properties of as-grown molecular beam epitaxy high-k gate dielectrics deposited on silicon

Authors: Goldenblum, A; Pintilie, I; Buda, M; Popa, A; Lisca, M; Botila, T; Teodorescu, V; Dimoulas, A; Vellianitis, G

Published: MAR 15 2006, JOURNAL OF APPLIED PHYSICS, 99, DOI: 10.1063/1.2180428

The carrier transport mechanisms in as-grown LaAlO3 and La2Hf2O7 high-k insulator layers deposited on n- and p-Si were deduced from temperature dependent C-V and I-V characteristics correlated with photoelectric measurements. Large, parallel shifts in the high frequency C-V curves are explained by the presence of a large density of interface states and an approximate analytical formula relating the density of states to the C-V shift is deduced. The space charge limited current is explained by the existence of impurity channels situated energetically near the conduction or valence band of silicon.

33. Recent advancements in the development of radiation hard semiconductor detectors for S-LHC

Authors: Fretwurst, E; Adey, J; Al-Ajili, A; Alfieri, G; Allport, PP; Artuso, M; Assouak, S; Avset, BS; Barabashi, L; Barcz, A; Bates, R; Biagi, SF; Bilei, GM; Bisello, D; Blue, A; Blumenau, A; Boisvert, V; Bolla, G; Bondarenko, G; Borchi, E; Borrello, L; Bortoletto, D; Boscardin, M; Bosisio, L; Bowcock, TJV; Brodbeck, TJ; Broz, J; Bruzzi, M; Brzozowski, A; Buda, M; Buhmann, P; Buttar, C; Campabadal, F; Campbell, D; Candelori, A; Casse, G; Cavallini, A; Charron, S; Chilingarov, A; Chren, D; Cindro, V; Collins, P; Coluccia, R; Contarato, D; Coutinho, J; Creanza, D; Cunningham, L; Dalla Betta, GF; Dawson, I; de Boer, W; De Palma, M; Demina, R; Dervan, P; Dittongo, S; Dolezal, Z; Dolgolenko, A; Eberlein, T; Eremin, V; Fall, C; Fasolo, F; Ferbel, T; Fizzotti, F; Fleta, C; Focardi, E; Forton, E; Garcia, C; Garcia-Navarro, JE; Gaubas, E; Genest, MH; Gill, KA; Giolo, K; Glaser, M; Goessling, C; Golovine, V; Sevilla, SG; Gorelov, I; Goss, J; Bates, AG; Gregoire, G; Gregori, P; Grigoriev, E; Grillo, AA; Groza, A; Guskov, J; Haddad, L; Harkonen, J; Hauler, F; Hoeferkamp, M; Honniger, F; Horazdovsky, T; Horisberger, R; Horn, M; Houdayer, A; Hourahine, B; Hughes, G; Ilyashenko, I; Irmscher, K; Ivanov, A; Jarasiunas, K; Johansen, KMH; Jones, BK; Jones, R; Joram, C; Jungermann, L; Kalinina, E; Kaminski, P; Karpenko, A; Karpov, A; Kazlauskiene, V; Kazukauskas, V; Khivrich, V; Khomenkov, V; Kierstead, J; Klaiber-Lodewigs, J; Klingenberg, R; Kodys, P; Kohout, Z; Korjenevski, S; Koski, M; Kozlowski, R; Kozodaev, M; Kramberger, G; Krasel, O; Kuznetsov, A; Kwan, S; Lagomarsino, S; Lassila-Perini, K; Lastovetsky, V; Latino, G; Lazanu, I; Lazanu, S; Lebedev, A; Lebel, C; Leinonen, K; Leroy, C; Li, Z; Lindstrom, G; Linhart, V; Litovchenko, P; Litovchenko, A; Giudice, AL; Lozano, M; Luczynski, Z; Luukka, P; Macchiolo, A; Makarenko, LF; Mandic, I; Manfredotti, C; Manna, N; Garcia, SM; Marunko, S; Mathieson, K; Melone, J; Menichelli, D; Messineo, A; Metcalfe, J; Miglio, S; Mikuz, M; Miyamoto, J; Moll, M; Monakhov, E; Moscatelli, F; Naoumov, D; Nossarzewska-Orlowska, E; Nysten, J; Olivero, P; Oshea, V; Palviainen, T; Paolini, C; Parkes, C; Pesseri, D; Pein, U; Pellegrini, G; Perera, L; Petasecca, M; Plemonte, C; Pignatel, GU; Pinho, N; Pintilie, I; Pintilie, L; Polivtsev, L; Polozov, P; Popa, A; Popule, J; Pospisil, S; Pozza, A; Radicci, V; Rafi, JM; Rando, R; Roeder, R; Rohe, T; Ronchin, S; Rott, C; Roy, A; Ruzin, A; Sadrozinski, HFW; Sakalauskas, S; Scaringella, M; Schiavulli, L; Schnetzer, S; Schumm, B; Sciortino, S; Scorzoni, A; Segneri, G; Seidel, S; Seiden, A; Sellberg, G; Sellin, P; Sentenac, D; Shipsey, I; Sicho, P; Sloan, T; Solar, M; Son, S; Sopko, B; Sopko, V; Spencer, N; Stahl, J; Stolze, D; Stone, R; Storasta, J; Strokan, N; Sudzius, M; Surma, B; Suvorov, A; Svensson, BG; Tipton, P; Tomasek, M; Tsvetkov, A; Tuominen, E; Tuovinen, E; Tuuva, T; Tylchin, M; Uebersee, H; Uher, J; Ullan, M; Vaitkus, JV; Velthuis, J; Verbitskaya, E; Vrba, V; Wagner, G; Wilhelm, I; Worm, S; Wright, V; Wunstorf, R; Yiuri, Y; Zabierowski, P; Zaluzhny, A; Zavrtanik, M; Zen, M; Zhukov, V; Zorzi, N

Published: OCT 21 2005, NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION A-ACCELERATORS SPECTROMETERS DETECTORS AND ASSOCIATED EQUIPMENT, 552, 19, DOI: 10.1016/j.nima.2005.05.039

The proposed luminosity upgrade of the Large Hadron Collider (S-LHC) at CERN will demand the innermost layers of the vertex detectors to sustain fluences of about 10(16) hadrons/cm(2). Due to the high multiplicity of tracks, the required spatial resolution and the extremely harsh radiation field new detector concepts and semiconductor materials have to be explored for a possible solution of this challenge. The CERN RD50 collaboration "Development of Radiation Hard Semiconductor Devices for Very High Luminosity Colliders" has started in 2002 an R&D program for the development of detector technologies that will fulfill the requirements of the S-LHC. Different strategies are followed by RD50 to improve the radiation tolerance. These include the development of defect engineered silicon like Czochralski, epitaxial and oxygen-enriched silicon and of other semiconductor materials like SiC and GaN as well as extensive studies of the microscopic defects responsible for the degradation of irradiated sensors. Further, with 3D, Semi-3D and thin devices new detector concepts have been evaluated. These and other recent advancements of the RD50 collaboration are presented and discussed. (c) 2005 Elsevier B.V. All rights reserved.

34. Radiation-hard semiconductor detectors for SuperLHC

Authors: Bruzzi, M; Adey, J; Al-Ajili, A; Alexandrov, P; Alfieri, G; Allport, PP; Andreazza, A; Artuso, M; Assouak, S; Avset, BS; Barabash, L; Baranova, E; Barcz, A; Basile, A; Bates, R; Belova, N; Biagi, SF; Bilei, GM; Bisello, D; Blue, A; Blumenau, B; Boisvert, V; Bolla, G; Bondarenko, G; Borchi, E; Borrello, L; Bortoletto, D; Boscardin, M; Bosisio, L; Bowcock, TJV; Brodbeck, TJ; Broz, J; Brukhanov, A; Brzozowski, A; Buda, M; Buhmann, P; Buttar, C; Campabadal, F; Campbell, D; Candelori, A; Casse, G; Cavallini, A; Chilingarov, A; Chren, D; Cindro, V; Citterio, M; Collins, P; Coluccia, R; Contarato, D; Coutinho, J; Creanza, D; Cunningham, W; Cvetkov, V; Dalla Betta, GF; Davies, G; Dawson, I; de Boer, W; De Palma, M; Demina, R; Dervan, P; Dierlamm, A; Dittongo, S; Dobrzanski, L; Dolezal, Z; Dolgolenko, A; Eberlein, T; Eremin, V; Fall, C; Fasolo, F; Ferbel, T; Fizzotti, F; Fleta, C; Focardi, E; Forton, E; Franchenko, S; Fretwurst, E; Gamaz, F; Garcia, C; Garcia-Navarro, JE; Gaubas, E; Genest, MH; Gill, KA; Giolo, K; Glaser, M; Goessling, C; Golovine, V; Sevilla, SG; Gorelov, I; Goss, J; Gouldwell, A; Gregoire, G; Gregori, P; Grigoriev, E; Grigson, C; Grillo, A; Groza, A; Guskov, J; Haddad, L; Harkonen, J; Harding, R; Hauler, F; Hayama, S; Hoeferkamp, M; Honniger, F; Horazdovsky, T; Horisberger, R; Horn, M; Houdayer, A; Hourahine, B; Hruban, A; Hughes, G; Ilyashenko, I; Irmscher, K; Ivanov, A; Jarasiunas, K; Jin, T; Jones, BK; Jones, R; Joram, C; Jungermann, L; Kalinina, E; Kaminski, P; Karpenko, A; Karpov, A; Kazlauskiene, V; Kazukauskas, V; Khivrich, V; Khomenkov, V; Kierstead, J; Klaiber-Lodewigs, J; Kleverman, M; Klingenberg, R; Kodys, P; Kohout, Z; Korjenevski, S; Kowalik, A; Kozlowski, R; Kozodaev, M; Kramberger, G; Krasel, O; Kuznetsov, A; Kwan, S; Lagomarsino, S; Lari, T; Lassila-Perini, K; Lastovetsky, V; Latino, G; Latushkin, S; Lazanu, S; Lazanu, I; Lebel, C; Leinonen, K; Leroy, C; Li, Z; Lindstrom, G; Lindstrom, L; Linhart, V; Litovchenko, A; Litovchenko, P; Litvinov, V; Lo Giudice, A; Lozano, M; Luczynski, Z; Luukka, P; Macchiolo, A; Mainwood, A; Makarenko, LF; Mandic, I; Manfredotti, C; Garcia, SM; Marunko, S; Mathieson, K; Mozzanti, A; Melone, J; Menichelli, D; Meroni, C; Messineo, A; Miglio, S; Mikuz, M; Miyamoto, J; Moll, M; Monakhov, E; Moscatelli, F; Murin, L; Nava, F; Naoumov, D; Nossarzewska-Orlowska, E; Nummela, S; Nysten, J; Olivero, P; Oshea, V; Palviainen, T; Paolini, C; Parkes, C; Passeri, D; Pein, U; Pellegrini, G; Perera, L; Petasecca, M; Piatkowski, B; Piemonte, C; Pignatel, GU; Pinho, N; Pintilie, I; Pintilie, L; Polivtsev, L; Polozov, P; Popa, AI; Popule, J; Pospisil, S; Pucker, G; Radicci, V; Rafi, JM; Ragusa, F; Rahman, M; Rando, R; Roeder, R; Rohe, T; Ronchin, S; Rott, C; Roy, P; Roy, A; Ruzin, A; Ryazanov, A; Sadrozinski, HFW; Sakalauskas, S; Scaringella, M; Schiavulli, L; Schnetzer, S; Schumm, B; Sciortino, S; Scorzoni, A; Segneri, G; Seidel, S; Seiden, A; Sellberg, G; Sellin, P; Sentenac, D; Shipsey, I; Sicho, P; Sloan, T; Solar, M; Son, S; Sopko, B; Spencer, N; Stahl, J; Stavitski, I; Stolze, D; Stone, R; Storasta, J; Strokan, N; Strupinski, W; Sudzius, M; Surma, B; Suuronen, J; Suvorov, A; Svensson, BG; Tipton, P; Tomasek, M; Troncon, C; Tsvetkov, A; Tuominen, E; Tuovinen, E; Tuuva, T; Tylchin, M; Uebersee, H; Uher, J; Ullan, M; Vaitkus, JV; Vanni, P; Velthuis, J; Verzellesi, G; Verbitskaya, E; Vrba, V; Wagner, G; Wilhelm, I; Worm, S; Wright, V; Wunstorf, R; Zablerowski, P; Zaluzhny, A; Zavrtanik, M; Zen, M; Zhukov, V; Zorzi, N

Published: APR 1 2005, NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION A-ACCELERATORS SPECTROMETERS DETECTORS AND ASSOCIATED EQUIPMENT, 541, 201, DOI: 10.1016/j.nima.2005.01.056

An option of increasing the luminosity of the Large Hadron Collider (LHC) at CERN to 1035 cm-2 s-1 has been envisaged to extend the physics reach of the machine. An efficient tracking down to a few centimetres from the interaction point will be required to exploit the physics potential of the upgraded LHC. As a consequence, the semiconductor detectors close to the interaction region will receive severe doses of fast hadron irradiation and the inner tracker detectors will need to survive fast hadron fluences of up to above 1016cm-2. The CERN-RD50 project "Development of Radiation Hard Semiconductor Devices for Very High Luminosity Colliders" has been established in 2002 to explore detector materials and technologies that will allow to operate devices up to, or beyond, this limit. The strategies followed by RD50 to enhance the radiation tolerance include the development of new or defect engineered detector materials (SiC, GaN, Czochralski and epitaxial silicon, oxygen enriched Float Zone silicon), the improvement of present detector designs and the understanding of the microscopic defects causing the degradation of the irradiated detectors. The latest advancements within the RD50 collaboration on radiation hard semiconductor detectors will be reviewed and discussed in this work. 2005 Published by Elsevier B.V.

35. Development of radiation tolerant semiconductor detectors for the Super-LHC

Authors: Moll, M; Adey, J; Al-Ajili, A; Alfieri, G; Allport, PP; Artuso, M; Assouak, S; Avset, BS; Barabash, L; Barcz, A; Bates, R; Biagi, SF; Bilei, GM; Bisello, D; Blue, A; Blumenau, A; Boisvert, V; Bolla, G; Bondarenko, G; Borchi, E; Borrello, L; Bortoletto, D; Boscardin, M; Bosisio, L; Bowcock, TJV; Brodbeck, TJ; Broz, J; Bruzzi, M; Brzozowski, A; Buda, M; Buhmann, P; Buttar, C; Campabadal, F; Campbell, D; Candelori, A; Casse, G; Cavallini, A; Charron, S; Chilingarov, A; Chren, D; Cindro, V; Collins, P; Coluccia, R; Contarato, D; Coutinho, J; Creanza, D; Cunningham, W; Dalla Betta, GF; Dawson, I; de Boer, W; De Palma, M; Demina, R; Dervan, P; Dittongo, S; Dolezal, Z; Dolgolenko, A; Eberlein, T; Eremin, V; Fall, C; Fasolo, F; Fizzotti, F; Fleta, C; Focardi, E; Forton, E; Fretwurst, E; Garcia, C; Garcia-Navarro, JE; Gaubas, E; Genest, MH; Gill, KA; Giolo, K; Glaser, M; Goessling, C; Golovine, V; Sevilla, SG; Gorelov, I; Goss, J; Bates, AG; Gregoire, G; Gregori, P; Grigoriev, E; Grillo, AA; Groza, A; Guskov, J; Haddad, L; Harkonen, J; Hauler, F; Hoeferkamp, M; Honniger, F; Horazdovsky, T; Horisberger, R; Horn, M; Houdayer, A; Hourahine, B; Hughes, G; Ilyashenko, I; Irmscher, K; Ivanov, A; Jarasiunas, K; Johansen, KMH; Jones, BK; Jones, R; Joram, C; Jungermann, L; Kalinina, E; Kaminski, P; Karpenko, A; Karpov, A; Kazlauskiene, V; Kazukauskas, V; Khivrich, V; Khomenkov, V; Kierstead, J; Klaiber-Lodewigs, J; Klingenberga, R; Kodys, P; Kohout, Z; Korjenevski, S; Koski, M; Kozlowski, R; Kozodaev, M; Kramberger, G; Krasel, O; Kuznetsov, A; Kwan, S; Lagomarsino, S; Lassila-Perini, K; Lastovetsky, V; Latino, G; Lazanu, S; Lazanu, I; Lebedev, A; Lebel, C; Leinonen, K; Leroy, C; Li, Z; Lindstrom, G; Linhart, V; Litovchenko, A; Litovchenko, P; Lo Giudice, A; Lozano, M; Luczynski, Z; Luukka, P; Macchiolo, A; Makarenko, LF; Mandic, I; Manfredotti, C; Manna, N; Marti i Garcia, S; Marunko, S; Mathieson, K; Melone, J; Menichelli, D; Messineo, A; Metcalfe, J; Miglio, S; Mikuz, M; Miyamoto, J; Monakhov, E; Moscatelli, F; Naoumov, D; Nossarzewska-Orlowska, E; Nysten, J; Olivera, P; OShea, V; Palvialnen, T; Paolini, C; Parkes, C; Passeri, D; Pein, U; Pellegrini, G; Perera, L; Petasecca, K; Piemonte, C; Pignatel, GU; Pinho, N; Pintilie, I; Pintilie, L; Polivtsev, L; Polozov, P; Popa, A; Popule, J; Pospisil, S; Pozza, A; Radicci, V; Rafi, JM; Rando, R; Roeder, R; Rohe, T; Ronchin, S; Rott, C; Roy, A; Ruzin, A; Sadrozinski, HFW; Sakalauskas, S; Scaringella, M; Schiavulli, L; Schnetzer, S; Schumm, B; Sciortino, S; Scorzoni, A; Segneri, G; Seidel, S; Seiden, A; Sellberg, G; Sellin, P; Sentenac, D; Shipsey, I; Sicho, P; Sloan, T; Solar, M; Son, S; Sopko, B; Sopko, V; Spencer, N; Stahl, J; Stolze, D; Stone, R; Storasta, J; Strokan, N; Sudzius, M; Surma, B; Suvorov, A; Svensson, BG; Tipton, P; Tomasek, M; Tsvetkov, A; Tuominen, E; Tuovinen, E; Tuuva, T; Tylchin, M; Uebersee, H; Uher, J; Ullan, M; Vaitkus, JV; Velthuis, J; Verbitskaya, E; Vrba, V; Wagner, G; Wilhelm, I; Worm, S; Wright, V; Wunstorf, R; Yiuri, Y; Zabierowski, P; Zaluzhny, A; Zavrtanik, M; Zen, M; Zhukov, V; Zorzi, N

Published: JUL 1 2005, NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION A-ACCELERATORS SPECTROMETERS DETECTORS AND ASSOCIATED EQUIPMENT, 546, 107, DOI: 10.1016/j.nima.2005.03.044

The envisaged upgrade of the Large Hadron Collider (LHC) at CERN towards the Super-LHC (SLHC) with a 10 times increased luminosity of 10(35) cm(-2) s(-1) Will present severe challenges for the tracking detectors of the SLHC experiments. Unprecedented high radiation levels and track densities and a reduced bunch crossing time in the order of 10 ns as well as the need for cost effective detectors have called for an intensive R&D program. The CERN RD50 collaboration "Development of Radiation Hard Semiconductor Devices for Very High Luminosity Colliders" is working on the development of semiconductor sensors matching the requirements of the SLHC. Sensors based on defect engineered silicon like Czochralski, epitaxial and oxygen enriched silicon have been developed. With 3D, Semi-3D and thin detectors new detector concepts have been evaluated and a study on the use of standard and oxygen enriched p-type silicon detectors revealed a promising approach for radiation tolerant cost effective devices. These and other most recent advancements of the RD50 collaboration are presented. (c) 2005 Elsevier B.V. All rights reserved.

36. Space-charge-limited current involving carrier injection into impurity bands of high-k insulators

Authors: Goldenblum, A; Pintilie, I; Buda, M; Popa, A; Botila, T; Dimoulas, A; Vellianitis, G

Published: MAY 16 2005, APPLIED PHYSICS LETTERS, 86, DOI: 10.1063/1.1935045

Photoelectrical measurements have shown that the current flow through La2Hf2O7 and LaAlO3 high-k insulator layers deposited on silicon takes place via impurity channels. A space charge limited current is evidenced, for different insulator thicknesses and temperatures, by the square law dependence of current versus voltage. The analysis demonstrates that this space charge limited (SCL) current in thin insulator films can be explained only by the presence of impurity channels situated near the Fermi level of the injecting contact. Many other aspects related to the SCL current behavior were found. (c) 2005 American Institute of Physics.

37. A model of the metallic surface-emitting second harmonic generator

Authors: Popa, A; Lazarescu, MF; Dabu, R; Stratan, A

Published: SEP 1997, IEEE JOURNAL OF QUANTUM ELECTRONICS, 33, 1480, DOI: 10.1109/3.622625

We present an accurate calculation of the intensity of the second harmonic radiation generated by the reflection of the incident radiation from a metal surface, This radiation is due to two currents, The first current results from the rapid variation of the normal component of the oscillating electric field in the vicinity of the surface and depends on both conduction and bound electrons, The second one results from the action of the Lorentz force on conduction electrons, We show that if the adiabatic and the Thomas-Fermi assumptions are considered, then an accurate calculation of these currents is possible and leads to a simple relation of the intensity of the second harmonic radiation.

38. MAGNETIC DOMAIN-STRUCTURE AND THERMOMAGNETIC WRITING ON AMORPHOUS GD-CO THIN-FILMS

Authors: SERBANESCU, MD; FLORESCU, V; MATEICIUC, V; POPA, A

Published: 1984, REVUE ROUMAINE DE PHYSIQUE, 29, 388, DOI:

39. STRUCTURE OF CHEMICALLY DEPOSITED NI/SI CONTACTS

Authors: DAN, PA; POPOVICI, G; DASCALU, D; BREZEANU, G; POPA, A

Published: 1983, JOURNAL OF THE ELECTROCHEMICAL SOCIETY, 130, 2478, DOI: 10.1149/1.2119616

40.

Authors: Popa, A; Ilia, G; Pascariu, A; Iliescu, S; Plesu, N

Published: 13 0, , DOI:

Dr. Adrian Claudiu POPA

Scientific Researcher III