Bulk MgB2 discs were prepared by an in situ route from mixtures of magnesium and boron powders. The boron powders were produced by two methods. The first one consisted of a self-propagating high tem-perature magnesiothermic synthesis (SHS) process followed by acid and fluorine cleaning and a heat treatment in inert atmosphere. This approach produced boron with purities between 86 % and 97 %, where the main impurity was Mg. Depending on the final heat treatment, these boron powders were amorphous or crystalline. In the second route, high purity nano powders (99 %) of boron were obtained by a diborane pyrolysis process. Bulks of MgB2 were characterized by structural, microstructural, and magnetic mea-surements. Critical current density, pinning force aspects and levitation force (including guiding force) details were assessed. Amorphous lower purity boron (86-97 %) obtained by the first processing route was found to promote the largest levitation forces of the MgB2 bulks and, among these samples, the best le-vitation results were recorded when using boron with a purity of 95-97 %. Use of a lower purity boron that decreases the cost of MgB2 promotes large scale production at industrial level of bulk MgB2 super-conducting magnets for levitation applications and enhances the applicability potential of MgB2 super-conductor. The relationship between levitation force and specific features of the samples such as pinning force details are discussed.& COPY; 2023 Elsevier B.V. All rights reserved.

The deposition of a ferromagnetic layer can affect the properties of high-temperature superconductors underneath. We investigated the influence of ferromagnetic CaRuO3 on the properties of YBa2Cu3O7-x (YBCO) superconducting thin films when the layers are either in direct contact or separated by a barrier layer of 5 nm SrTiO3. Detailed measurements of the magnetic moment of the superconductor and ferromagnet as a function of temperature and magnetic field have been performed using SQUID magnetometry. Magnetometry and relaxation measurements show that the modification of the superconducting properties of YBCO strongly depends on the interaction with the ferromagnetic layer on top. The barrier layer has a significant impact on both the supercon-ducting properties of the YBCO film and the ferromagnetic ordering of CaRuO3. The physical properties mentioned above were discussed in correlation with the materials' structure determined by XRD analysis.

In this work, we report the preparation of nanostructured electrodes based on dense arrays of vertically-aligned copper (Cu) nanowires (NWs) to be subsequently covered by cadmium telluride (CdTe) thin films, with great potential to be used within "substrate"-type photovoltaic cells based on A(II)-BVI heterojunctions. In particular, the multi-step preparation protocol presented here involves an electrochemical synthesis procedure within a supported anodic aluminum oxide (AAO) nanoporous template for first generating a homogeneous array of vertically-aligned Cu NWs, which are then further embedded within a compact CdTe thin film. In a second stage, we tested three deposition methods (vacuum thermal evaporation, VTE; radio-frequency magnetron sputtering, RF-MS; and electrochemical deposition, ECD) for use in obtaining CdTe layers potentially able to consistently penetrate the previously prepared Cu NWs array. A comparative analysis was performed to critically evaluate the morphological, optical, and structural properties of the deposited CdTe films. The presented results demonstrate that under optimized processing conditions, the ECD approach could potentially allow the cost-effective fabrication of absorber layer/collecting electrode CdTe/Cu nanostructured interfaces that could improve charge collection mechanisms, which in turn could allow the fabrication of more efficient solar cells based on A(II)-BVI semiconducting compounds.

Direct current (DC) and radio frequency (RF) magnetron sputtering methods were selected for conducting the deposition of structural materials, namely ceramic and metallic co-depositions. A total of six configurations were deposited: single thin layers of oxides (Cr2O3, SiO2) and co-deposition configurations (50:50 wt.%) as structural materials (W, Be)-(Cr2O3, SiO2), all deposited on 304L stainless steel (SS). A comprehensive evaluation such as surface topology, thermal desorption outgassing, and structural/chemical state was performed. Moreover, mechanical characterization evaluating properties such as adherence, nano indentation hardness, indentation modulus, and deformation relative to yielding, was performed. Experimental results show that, contrary to SiO2 matrix, the composite layers of Cr2O3 with Be and W exhibit surface smoothing with mitigation of artifacts, thus presenting a uniform and compact state with the best microstructure. These results are relevant in order to develop future dense coatings to be used in the fusion domain.

AuxFe1-x nanophase thin films of different compositions and thicknesses were prepared by co-deposition magnetron sputtering. Complex morpho-structural and magnetic investigations of the films were performed by X-ray Diffraction, cross-section Transmission Electron Microscopy, Selected Area Electron Diffraction, Magneto Optical Kerr Effect, Superconducting Quantum Interference Device magnetometry and Conversion Electron Mossbauer Spectroscopy. It was proven that depending on the preparation conditions, different configurations of defect alpha-Fe magnetic clusters, i.e., randomly distributed or auto-assembled in lamellar or filiform configurations, can be formed in the Au matrix. A close relationship between the Fe clustering process and the type of the crystalline structure of the Au matrix was underlined, with the stabilization of a hexagonal phase at a composition close to 70 at. % of Au and at optimal thickness. Due to different types of inter-cluster magnetic interactions and spin anisotropies, different types of magnetic order from 2D Ising type to 3D Heisenberg type, as well as superparamagnetic behavior of non-interacting Fe clusters of similar average size, were evidenced.

The manipulation of magnetic anisotropy represents the fundamental prerequisite for the application of magnetic materials. Here we present the vectorial magnetic properties of nanostructured systems and thin films of Fe and FeCo prepared on linearly trenched Mo templates with thermally controlled periodicity. The magnetic properties of the nanosystems are engineered by tuning the shape, size, thickness, and composition parameters of the thin films. Thus, we control coercivity, magnetization, orientation of the easy axis of magnetization, and the long-range magnetic order of the system in the function of the temperature. We distinguish magnetic components that emerge from the complex morpho-structural features of the undulating Fe or FeCo nanostructured films on trenched Mo templates: (i) assembly of magnetic nanowires and (ii) assembly of magnetic islands/clusters. Uniaxial anisotropy at room temperature was proven, characterized, and explained in the case of all systems. Our work contributes to the understanding of magnetic properties necessary for possible further applications of linear systems and undulated thin films.

In the present study, the synthesis of titanium nitride (TiN) by carbothermal reduction nitridation (CRN) reaction using nanocomposites made of mesoporous TiO2/acrylonitrile with different content of inorganic phase were explored. The choice of hybrid nanocomposite as precursor for the synthesis of TiN was made due to the possibility of having an intimate interface between the organic and inorganic phases in the mixture that can favours CRN reaction. Subsequently, the hybrid composites have been subjected to four-step thermal treatments at 290 degrees C, 550 degrees C, 1000 degrees C and 1400 degrees C under nitrogen atmosphere. The XRD results after thermal treatment at 1000 degrees C under nitrogen flow show the coexistence of two crystalline phases of TiO2, i.e. anatase and rutile, as well as TiN phase, together with the detection of amorphous carbon that proved the initiation of CRN reaction. Furthermore, the observations based on XRD patterns of samples thermally treated at 1400 degrees C in nitrogen atmosphere were in agreement with SEM analysis, that shows the formation of TiN by CRN reaction via hybrid nanocomposites mesoporous TiO2/acrylonitrile.

Pottery vessels made of kaolin clay from the Roman Period (2nd, 3rd centuries CE) found in Romula (Re?ca village, Olt County, Romania) from Dacia Inferior (Malvensis) were investigated by petrographic, X-ray diffraction, X-ray fluorescence, thermal analysis, electron microscopy, and mechanical tests. Our results are compared with available data on kaolin clays and pottery vessels from other sites located along the lower course of Danube river and near the Black Sea, namely in Moesia Superior, Moesia Inferior, and Thracia. Archeological and geographical contexts are addressed. Results of our analysis suggest a local production of ceramics in Romula, by using raw materials from the north of Lower Danube, in opposition to the idea that kaolin ware was imported from the provinces south of the Danube.

We report the facile and low-cost preparation as well as detailed characterization of dense arrays of passivated ferromagnetic nickel (Ni) nanotubes (NTs) vertically-supported onto solid Au-coated Si substrates. The proposed fabrication method relies on electrochemical synthesis within the nanopores of a supported anodic aluminum oxide (AAO) template and allows for fine tuning of the NTs ferromagnetic walls just by changing the cathodic reduction potential during the nanostructures' electrochemical growth. Subsequently, the experimental platform allowed further passivation of the Ni NTs with the formation of ultra-thin antiferromagnetic layers of nickel oxide (NiO). Using adequately adapted magnetic measurements, we afterwards demonstrated that the thickness of the NT walls and of the thin antiferromagneticNiO layer, strongly influences the magnetic behavior of the dense array of exchange-coupled Ni/NiO NTs. The specific magnetic properties of these hybrid ferromagnetic/antiferromagnetic nanosystems were then correlated with the morpho-structural and geometrical parameters of the NTs, as well as ultimately strengthened by additionally-implemented micromagnetic simulations. The effect of the unidirectional anisotropy strongly amplified by the cylindrical geometry of the ferromagnetic/antiferromagnetic interfaces has been investigated with the magnetic field applied both parallel and perpendicular to the NTs axis.

Indium-doped tin oxide (ITO) thin films were fabricated by radio frequency magnetron sputtering and were subjected to in-situ and ex-situ annealing, at 200 degrees C, 300 degrees C and 400 degrees C, respectively. The in-situ thermal treatment consisted to intentionally heating the samples' substrates, while the ex-situ annealing was performed using an oven, under ambient atmosphere. For the ITO samples subjected to ex-situ annealing, the density of oxygen vacancies increased leading to the decrease of the electrical resistivity. No significant changes were noticed in terms of transmission spectroscopy after the thermal treatment; while by evaluating the Skewness parameter was determined that the annealing improves the planarity of samples' surface.

Indium-doped zinc oxide (IZO) and aluminium-doped zinc oxide (AZO) thin films were grown by radio-frequency (RF) magnetron sputtering onto optical glass substrates and their structural, morphological, and optical properties were discussed in terms of varying the sputtering power as 40 W, 60 W, 80 W, and 100 W. No heating substrate or any post-thermal treatment was performed. The structural features were analyzed by grazing incidence X-ray diffraction and revealed the amorphous phase for IZO samples, while the AZO thin films inherited the Wurtzite structure of zinc oxide. The morphological properties were investigated by atomic force microscopy (AFM), in tapping mode and scanning electronmicroscopy (SEM). The AFM images showed relatively uniform and smooth surfaces for all prepared structures. The optical transmission spectra proved the excellent theoretical values of transparency for metallic oxides in the visible region of the electromagnetic spectrum, i.e. similar to 60% for IZO and similar to 70% for AZO. The obtained results showed that even without any thermal treatment the structural, morphological, and optical properties of IZO and AZO thin films prepared by RF magnetron sputtering are similar with those for samples subjected to medium or high temperatures.

Copper (Cu) and dysprosium (Dy) co-doped zinc oxide (ZnO) thin films were fabricated by radio frequency magnetron sputtering (RF-magnetron sputtering) using a homemade target having the atomic percentage of Cu and Dy of 1%, onto optical glass substrates and quartz substrates. The structural, morphological, optical, and electrical properties of fabricated ZnO:(Cu, Dy) structures were analyzed and discussed. It was found that all samples have hexagonal Wurtzite structure. Optical transmission measurements indicate values larger than 75% in the 400-2500 nm ranges. The current-voltage characteristics of hybrid heterojunctions based on ZnO:(Cu, Dy) and poly(3-hexylthiophene-2.5-diyl) (P3HT) or copper (II) phthalocyanine (CuPc) thin films were acquired in the dark, in ambient atmosphere, and they exhibit the typical diode behavior, almost free of electrical hysteresis.