This study describes the development of a pyruvate kinase (PyK)-biosensor for the evaluation of PyK activity, as a diagnostic tool for early cancer screening and detection of kinase inhibitors used in cancer treatment, with the evaluation of the inhibition mechanism. The biosensor was constructed by co-immobilizing the enzymes PyK and pyruvate oxidase (PyOx) on Au film electrodes by crosslinking with glutaraldehyde (GA) and evaluated electrochemically by cyclic voltammetry (CV) and fixed potential amperometry (CA). First, the experimental conditions were optimized in terms of applied potential, enzyme ratio PyK:PyOx and enzyme substrate concentration: phosphoenolpyruvate (PEP) and adenosine diphosphate (ADP). The biosensor sensitivity towards PEP detection was 2.11 +/- 0.08 mu A mM- 1 cm- 2, with very high reproducibility and repeatability, which made it suitable for inhibition studies of PyK inhibitor. The inhibition mechanism of shikonin was determined in relation to both PEP and ADP, with the calculation of IC50 values and binding constants (Ki). Detection of shikonin was possible at very low concentrations in the linear range of 0.1-4.0 pM. The electrochemical results were validated by UV-Vis spectrophotometry. The developed biosensor is a valuable tool for drug screening by enabling enzyme catalytic function examination with applicability to identify inhibitors, estimate their affinity, inhibition mechanism linked to their molecular mechanisms of action and evaluate selectivity, of great interest in both pharmaceutical and medical domains.

This work describes the development of a flexible uric acid (UA) biosensor based on palladium-coated submicrometer electrospun poly(methylmethacrylate) (PMMA) fibers metalized with gold and attached to polyethylene terephthalate substrate (Pd/Au/PMMA/PET). The morphological characterization conducted by scanning electron microscopy revealed nanoscale Pd dendritic structures. Electrochemical investigations in the absence and in the presence of redox probes demonstrated that these Pd nanostructures are responsible for a six-fold increase in the electroactive area and enhanced electron transfer kinetics when compared to the gold-coated electrospun fibers. The UA biosensor obtained by immobilizing the uricase enzyme (UrOx) onto the Pd/Au/PMMA/PET electrode surface, allowed UA detection with a sensitivity of 431 mu A cm(-2) mM(-1) and a limit of detection of 12 mu M. Investigation of the redox reactions of hydrogen peroxide (a product of the enzymatic oxidation of UA by UrOx) at the Pd/Au/PMMA/PET electrode demonstrated that the working principle of the biosensor is based on the reduction of PdO produced at the electrode surface during the spontaneous reduction of hydrogen peroxide on Pd. This allows a biosensor operating potential of -0.05 V (vs Ag/AgCl) with high selectivity. The UrOx/Pd/Au/PMMA/PET biosensor was applied for UA detection in body fluids (sweat, urine, and blood serum) with recovery values between 98 and 105%, which were validated by high-performance liquid chromatography analysis. The stability of the device was evaluated over a period of 3 months, retaining 78% of the initial sensitivity, and reproducibility with RSD = 4.9% was achieved. The analytical performance of the biosensor under harsh mechanical deformations and at physiological temperatures demonstrated the potential applications of the device to wearable sensing platforms.

This work describes the development of a flexible uric acid (UA) biosensor based on palladium-coated submicrometer electrospun poly(methylmethacrylate) (PMMA) fibers metalized with gold and attached to polyethylene terephthalate substrate (Pd/Au/PMMA/PET). The morphological characterization conducted by scanning electron microscopy revealed nanoscale Pd dendritic structures. Electrochemical investigations in the absence and in the presence of redox probes demonstrated that these Pd nanostructures are responsible for a six-fold increase in the electroactive area and enhanced electron transfer kinetics when compared to the gold-coated electrospun fibers. The UA biosensor obtained by immobilizing the uricase enzyme (UrOx) onto the Pd/Au/PMMA/PET electrode surface, allowed UA detection with a sensitivity of 431 mu A cm(-2) mM(-1) and a limit of detection of 12 mu M. Investigation of the redox reactions of hydrogen peroxide (a product of the enzymatic oxidation of UA by UrOx) at the Pd/Au/PMMA/PET electrode demonstrated that the working principle of the biosensor is based on the reduction of PdO produced at the electrode surface during the spontaneous reduction of hydrogen peroxide on Pd. This allows a biosensor operating potential of -0.05 V (vs Ag/AgCl) with high selectivity. The UrOx/Pd/Au/PMMA/PET biosensor was applied for UA detection in body fluids (sweat, urine, and blood serum) with recovery values between 98 and 105%, which were validated by high-performance liquid chromatography analysis. The stability of the device was evaluated over a period of 3 months, retaining 78% of the initial sensitivity, and reproducibility with RSD = 4.9% was achieved. The analytical performance of the biosensor under harsh mechanical deformations and at physiological temperatures demonstrated the potential applications of the device to wearable sensing platforms.

A nanostructured samarium oxide electrode was constructed by electrodeposition onto the surface of a gold electrode on SiO2/Si wafer. The samarium oxides electrode's surface morphology was investigated by scanning electron microcopy showing a quasi-monodispersed nanoplatelets like structure. X-rays diffraction analysis demonstrated a mixture of monoclinic and hexagonal phases while the X-rays photoelectron spectroscopy indicated the co-existence of both Sm2+ and Sm3+ species in a 1:3 proportion. Cyclic voltammetry and electrochemical impedance spectroscopy were used to investigate the charge transfer processes at the surface of the samarium oxide electrode in the absence and in the presence of redox probes. A roughness factor of 2.5 was determined from the samarium oxide electrode while the charge transfer constant was almost double when compared to the planar gold electrode. Then, the samarium oxide electrode was used for the H2O2 detection by fixed potential amperometry at -0.20 V (vs. Ag/AgCl) with a linear region between 0.01 and 1.00 mM, a sensitivity of 153 mu A cm(-2) mM(-1) and a LoD = 2.70 mu M. Glucose oxidase was used as a model enzyme in order to test the capacity of the samarium oxides electrode for biosensing. The enzyme was immobilized by physical adsorption and the optimum conditions for glucose analysis investigated. The biosensor showed a linear range for glucose detection between 0.10 and 1.20 mM with a sensitivity of 8.40 mu A cm(-2) mM(-1) and a LoD = 8.00 mu M. Selectivity was tested toward common interfering species, and the results revealed the lack of biosensor response. The glucose biosensor on samarium oxides was tested for glucose detection in serum samples with a recovery factor of 90%, and the result validated with a commercial glucometer. (C) 2021 Elsevier Ltd. All rights reserved.

A novel nanostructured platform for pyruvate oxidase biosensors comprises poly(neutral red) (PNR) prepared by electropolymerization of NR in ethaline deep eutectic solvent (DES) with acid dopant, on a multiwalled carbon nanotubes (MWCNT) modified glassy carbon electrode (GCE). Characterization was by cyclic voltammetry and electrochemical impedance spectroscopy and morphology was examined by scanning electron microscopy. Ascorbate and H2O2 gave a better response at PNRDES/GCE than at PNRaq/GCE. Biosensors for pyruvate and phosphate, immobilizing pyruvate oxidase onto PNRDES/MWCNT/GCE enabled selective determination of pyruvate and phosphate, with micromolar limits of detection. Pyruvate was determined in onion samples and phosphate in water samples.

Electrospun polymeric fibers present an emerging alternative for the development of flexible electronics, enabling applications in wearable sensors and biosensors for continuous monitoring, and actuators for tissue engineering. The possibility to prepare sub-micrometric polymeric scaffolds, their processing for increasing the conductivity, their modification with different materials, conductive polymers and biomolecules in order to obtain functional flexible electrodes, allows the development of innovative devices for healthcare, and biomedical applications. In this review, the impact of metallized electrospun polymeric fibers in electrochemical (bio)sensors and actuators is discussed. A relation between their structure and functionality is provided, alongside with an overview of the different methods to obtain functional conductive fibers.

Shikonin, a natural compound with pharmaceutical properties, has attracted interest due to its anti-oxidant properties, potential anti-cancer activity and activity over several biological pathways, such as dsDNA transcription/replication of cancer cells and inhibition of pyruvate kinase M2. The electrochemical behavior of shikonin in aqueous media was investigated at glassy carbon electrodes by cyclic and differential pulse voltammetry. The reduction involves the quinone moiety and formation of a semiquinone intermediate. In the absence of dissolved oxygen, the reduction is reversible while in normal atmosphere leads to formation of superoxide cation. The oxidation occurs at the dihydroxy moiety and reversibility was only observed in acid electrolytes. A redox mechanism was proposed. The interaction between shikonin and dsDNA was evaluated in incubated solutions and in situ with the dsDNA-electrochemical biosensor. The mechanism of interaction is time-dependent and follows an initial binding step at the grooves of the double strand leading to conformational modifications recognized through the variation of guanine and adenine oxidation peaks. The in-situ electrochemical production of the semiquinone intermediate leads to a preferential interaction with guanine residues, promoting their oxidation and consequently occurrence 8-oxo-guanine. An interaction mechanism was proposed.

The use of gold nanoparticles/superoxide dismutase (AuNP/SOD) bioconjugates is described as building blocks in SOD biosensor development for the quantification of superoxide in cell culture media. AuNP functionalization with 11-mercaptoundecanoic acid (MUA) and 4-mercaptobenzoic acid (MBA) (AuNPMUA and AuNPMBA) was used to improve SOD immobilization through EDC/NHS coupling using their -COOH terminus, leading to the formation of more stable bioconjugates. AuNP and AuNP/SOD bioconjugates were characterized by SEM to determine their size and morphology, UV-Vis for optical properties, FT-IR, and Raman spectroscopies for chemical functional group analysis and EDX for elemental analysis. Electrochemical methods were used to characterize the Au/AuNP-modified electrodes. For the optimization of the biosensor architecture, different AuNP/enzyme bioconjugates were prepared by varying the amount of both enzyme and AuNP, as well as their incubation time. Finally, the biosensors incorporating the bioconjugates were characterized by fixed potential amperometry and voltammetric analysis in order to establish the enzymatic mechanism and to elucidate the best biosensor architecture for monitoring superoxide in cell culture media. The best sensitivity value for superoxide detection corresponded to 41.2 nA mu M cm(-2), achieved by a biosensor based on AuNPMBA/SOD bioconjugates monitored through fixed potential amperometry at 0.3 V vs. Ag/AgCl, with a limit of detection of 1.0 mu M, and overall very good operational stability, maintaining 91% of the initial sensitivity after 30 days. Finally, the optimized biosensor was employed for the quantification of successive additions of superoxide in cell culture media, with excellent recovery values.

Fibres of poly(methyl methacrylate) were obtained by electrospinning, subjected to coating with a gold layer and then attached on a thin polyethylene terephthalate substrate in order to obtain flexible electrodes for biosensing applications. The morphology of these electrodes, investigated by scanning electron microscopy showed multilayers of random oriented fibres of approx. 400 nm diameter. The electrochemical characterization of these flexible electrodes was performed by cyclic voltammetry and electrochemical impedance spectroscopy in acid and neutral media, in the absence and in the presence of redox probes, proving their superior performance (e.g. 5fold current density value) when compared to planar gold electrodes obtained on silicon wafers. The electrodes obtained from conductive electrospun polymeric fibres nets were tested by cyclic voltammetry and amperometry for the detection of hydrogen peroxide with a sensitivity of 0.84 mA cm-2 mM-1 and a detection limit of 20.40 ?M. The immobilization of the model enzyme glucose oxidase at the surface of the gold-coated electrospun polymeric fibres electrode was investigated and the obtained biosensor was applied for glucose determination in aqueous solutions by fixed potential amperometry with a sensitivity of 3.10 ?A cm-2 mM-1, a detection limit of 0.33 mM, and reduced interferences. Also, the practical applicability of the biosensor was tested for the detection of glucose in artificial sweat and serum samples.

The present work describes the electrochemical properties of ionophores immobilized at the surface of electrodes obtained from electrospun polymeric fibers, in order to develop sensors for the analysis of electrolytes. Poly(methyl methacrylate) submicrometer fibers were prepared by electrospinning, coated with a gold layer by magnetron sputtering and then transferred on polyethylene terephthalate (PET) in order to obtained flexible electrodes. The ionophores were immobilized at the surface of these electrodes by drop-casting a ionophore-Nafion mixed solution. The sensor surface was investigated by scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy in order to understand the morphology and distribution of a model Ca2+ ionophore over the electrode surface. Also, Fourier-transformed infrared spectroscopy was performed and demonstrated that the model Ca2+ ionophore can be immobilized in the nafion matrix maintaining its conformation, while cyclic voltammetry and electrochemical impedance spectroscopy demonstrated that the Ca2+ ionophore allows the diffusion of target ions through this this type of membrane. In order to prove the concept of ionophore-based sensors for the analysis of some electrolytes, Ca2+, NH4+, Cl- and H+ ionophore immobilized in a nafion matrix at the surface of these flexible electrodes were tested and the determination of the target ions performed by potentiometry in different media including artificial sweat. Finally, sensitivities, limits of detection, selectivity coefficients were determined. (C) 2020 Elsevier Ltd. All rights reserved.