Publications

Mixtures of B4C, alpha-AlB12 and B powders were reactively spark plasma sintered at 1800 degrees C. Crystalline and amorphous boron powders were used. Samples were tested for their impact behavior by the Split Hopkinson Pressure Bar method. When the ratio R = B4C/alpha-AlB12 >= 1.3 for a constant B-amount, the major phase in the samples was the orthorhombic AlB24C4, and when R < 1 the amount of AlB24C4 significantly decreased. Predictions that AlB24C4 has the best mechanical impact properties since it is the most compact and close to the ideal cubic packing among the Al-B-C phases containing B-12-type icosahedra were partially confirmed. Namely, the highest values of the Vickers hardness (32.4 GPa), dynamic strength (1323 MPa), strain and toughness were determined for the samples with R = 1.3, i.e., for the samples with a high amount of AlB24C4. However, the existence of a maximum, detectable especially in the dynamic strength vs. R, indicated the additional influence of the phases and the composite's microstructure in the samples. The type of boron does not influence the dependencies of the indicated mechanical parameters with R, but the curves are shifted to slightly higher values for the samples in which amorphous boron was used.

Several technological routes are being investigated for improving the energy storage capability and power delivery of electrochemical capacitors. In this work, ternary hybrid electrodes composed of conducting graphene/reduced graphene oxide (rGO), which store charge mainly through electric double-layer mechanisms, covered by NiO nanostructures, for adding pseudocapacitance, were fabricated through a matrix assisted pulsed laser evaporation technique. The incorporation of multiwall carbon nanotubes (MWCNTs) provokes an increase of the porosity and thus, a substantial enhancement of the electrodes' capacitance (from 4 to 20 F cm(-3) at 10 mV s(-1)). Volumetric capacitances of 34 F cm(-3) were also obtained with electrodes containing just carbon nanotubes coated with NiO nanostructures. Moreover, the use of nitrogen containing precursors (ammonia, urea) for laser-induced N-doping of the nanocarbons also provokes a notable increase of the capacitance. Remarkably, N-containing groups in rGO-MWCNTs mainly add electric double layer charge storage, pointing to an increase of electrode porosity, whereas redox reactions contribute with a minor diffusion fraction. It was also observed that the loading of carbon nanotubes leads to an increase of diffusion-controlled charge storage mechanisms versus capacitive ones in rGO-based electrodes, the opposite effect being observed in graphene electrodes.

Reduced activation ferritic and martensitic steel like EUROFER (9Cr-1W) are considered as potential structural materials for the first wall of the future next-generation DEMOnstration Power Station (DEMO) fusion reactor and as a reference material for the International Thermonuclear Experimental Reactor (ITER) test blanket module. The primary motivation of this work is to study the re-deposition of the main constituent materials of EUROFER, namely tungsten (W), iron (Fe), and chromium (Cr), in a DEMO type reactor by producing and analyzing complex WxCryFe1-x-y layers. The composite layers were produced in laboratory using the thermionic vacuum arc (TVA) method, and the morphology, crystalline structure, elemental composition, and mechanical properties were studied using scanning electron microscopy (SEM), X-ray diffraction (XRD), micro-X-ray fluorescence (micro-XRF), and glow discharge optical emission spectrometry (GDOES), as well as nanoindentation and tribology measurements. The results show that the layer morphology is textured and is highly dependent on sample positioning during the deposition process. The formation of polycrystalline WxCryFe1-x-y was observed for all samples with the exception of the sample positioned closer to Fe anode during deposition. The crystalline grain size dimension varied between 10 and 20 nm. The composition and thickness of the layers were strongly influenced by the in-situ coating position, and the elemental depth profiles show a non-uniform distribution of Fe and Cr in the layers. The highest hardness was measured for the sample positioned near the Cr anode, 6.84 GPa, and the lowest was 4.84 GPa, measured for the sample positioned near the W anode. The tribology measurements showed an abrasive sliding wear behavior for most of the samples with a reduction of the friction coefficient with the increase of the normal load.

The bio hydroxyapatite (HAp) was used from a long time in different medical and environmental applications. The HAp layers with a uniform surface were used for various medical applications such as orthopedic and dental metal implants. In this work, we reported on the influence of X-ray radiation on the structural and morphological properties of composite layers based on HAp and polydimethylsiloxane (PDMS) deposited on titanium substrates. The HAp:PDMS layers were investigated by different complementary methods such as scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and glow discharge optical emission spectrometry (GDOES). FTIR spectral analysis showed that the molecular structure of the coatings was not changed after their irradiation even though, the depth profile analysis performed by GDOES indicated a depletion of Ca and P elements from the HAp:PDMS irradiated samples. By SEM, we showed that the morphological features of the coatings were also changed, as the irradiated layers are delaminated. The biological assays confirmed that the antibacterial activity of HAp:PDMS composite layers increased after irradiation. The results obtained in this study highlighted that the biological properties of HAp:PDMS layers could be influenced by irradiation. (C) 2019 Society of Plastics Engineers.

In this study, the results about the influence of the surface morphology of layers based on montmorillonite (MMT) and silver (Ag) on antimicrobial properties are reported. The coating depositions were performed in the plasma of a radio frequency (RF) magnetron sputtering discharge. The studied layers were single montmorillonite layers (MMT) and silver/montmorillonite multilayers (MMT-Ag) obtained by magnetron sputtering technique with a different surface thickness. The resultant MMT-Ag biocomposite multilayers exhibited a uniform distribution of constituent elements and enhanced antimicrobial properties against fungal biofilm development. Glow-discharge optical emission spectroscopy (GDOES) analysis revealed the formation of MMT-Ag biocomposite multilayers following the deposit of a silver layer for an MMT layer that was initially deposited on a Si substrate. The surface morphology and thickness evaluation of deposited biocomposite layers were performed by scanning electron microscopy (SEM). A qualitative analysis of the chemical composition of thin layers was performed and the elements O, Ag, Mg, Fe, Al, and Si were identified in the MMT-Ag biocomposite multilayers. The in vitro antifungal assay proved that the inhibitory effect against the growth of Candida albicans ATCC 101231 CFU was more emphasized in the case of MMT-Ag biocomposite multilayers that in the case of the MMT layer. Cytotoxicity studies performed on HeLa cells showed that the tested layers did not show significant toxicity at the time intervals during which the assay was performed. On the other hand, it was observed that the MMT layers exhibited slightly higher biocompatible properties than the MMT-Ag composite layers.

Raman investigations on nanocomposites obtained by loading various amounts of vapor grown carbon nanofibers within an isotactic polypropylene matrix, and gamma irradiated in air, at various integral doses ranging between 0 and 27 kGy, are reported. The analysis is focused on the polymer's answers as revealed by Raman spectroscopy and investigate in detail the effect of ionizing radiation on the position of the Raman line originating from the polymer. The as-obtained data are correlated to the elastic features of the nanocomposites. A competition between gamma irradiation and loading by carbon nanofiber, resulting in the stretching of the polymeric matrix and revealed as a displacement of Raman lines towards smaller wavenumber is reported. It is concluded that side groups (CH3) are less affected by the loading with carbon nanofibers,

Ti6Al4V cranial prostheses in the form of patterned meshes were 3D printed by selective laser melting in an argon environment; using a CO2 laser source and micron-sized Ti6Al4V powder as the starting material. The size and shape of prostheses were chosen based on actual computer tomography images of patient skull fractures supplied in the framework of a collaboration with a neurosurgery clinic. After optimizations of scanning speed and laser parameters, the printed material was defect-free (as shown by metallographic analyses) and chemically homogeneous, without elemental segregation or depletion. The prostheses were coated by radio-frequency magnetron sputtering (RF-MS) with a bioactive thin layer of hydroxyapatite using a bioceramic powder derived from biogenic resources (Bio-HA). Initially amorphous, the films were converted to fully-crystalline form by applying a post-deposition thermal-treatment at 500 degrees C/1 h in air. The X-ray diffraction structural investigations indicated the phase purity of the deposited films composed solely of a hexagonal hydroxyapatite-like compound. On the other hand, the Fourier transform infrared spectroscopic investigations revealed that the biological carbonatation of the bone mineral phase was well-replicated in the case of crystallized Bio-HA RF-MS implant coatings. The in vitro acellular assays, performed in both the fully inorganic Kokubo's simulated body fluid and the biomimetic organic-inorganic McCoy's 5A cell culture medium up to 21 days, emphasized both the good resistance to degradation and the biomineralization capacity of the films. Further in vitro tests conducted in SaOs-2 osteoblast-like cells showed a positive proliferation rate on the Bio-HA RF-MS coating along with a good adhesion developed on the biomaterial surface by elongated membrane protrusions.

Iron oxide nanoparticles have been extensively studied for challenges in applicable areas such as medicine, pharmacy, and the environment. The functionalization of iron oxide nanoparticles with dextran opens new prospects for application. Suspension characterization methods such as dynamic light scattering (DLS) and zeta potential (ZP) have allowed us to obtain information regarding the stability and hydrodynamic diameter of these suspended particles. For rigorous characterization of the suspension of dextran-coated iron oxide nanoparticles (D-MNPs), studies have been performed using ultrasound measurements. The results obtained from DLS and ZP studies were compared with those obtained from ultrasound measurements. The obtained results show a good stability of D-MNPs. A comparison between the D-MNP dimension obtained from transmission electron microscopy (TEM), X-ray diffraction (XRD), and DLS studies was also performed. A scanning electron spectroscopy (SEM) image of a surface D-MNP layer obtained from the stable suspension shows that the particles are spherical in shape. The topographies of the elemental maps of the D-MNP layer showed a uniform distribution of the constituent elements. The homogeneity of the layer was also observed. The morphology of the HeLa cells incubated for 24 and 48 h with the D-MNP suspension and D-MNP layers did not change relative to the morphology presented by the control cells. The cytotoxicity studies conducted at different time intervals have shown that a slight decrease in the HeLa cell viability after 48 h of incubation for both samples was observed.

Monolayers of transition metal (from the group VI B) dichalcogenides (MoS2, MoSe2, WS2 and WSe2) show nonvolatile resistance switching: a transition from a high to a low resistance state. Here we propose two explanations for this behaviour. The first one is that the transition metals swaps from a trigonal prismatic to an octahedral coordination (due to a high applied electric field and pressure) and thus the monolayer switches from a semiconducting to a metallic phase. The second one is a two-step process where the high electric field and pressure break the M-X bonds and the transition metal atoms become firstly tetrahedrally coordinated and afterwards square-planar coordinated. Thus, all transition metal and chalcogen atoms are in the same plane, and the transition metal atoms are in contact with the atoms of the top and bottom electrodes.

Indium-doped zinc oxide (IZO) and aluminium-doped zinc oxide (AZO) thin films were grown by radio-frequency (RF) magnetron sputtering onto optical glass substrates and their structural, morphological, and optical properties were discussed in terms of varying the sputtering power as 40 W, 60 W, 80 W, and 100 W. No heating substrate or any post-thermal treatment was performed. The structural features were analyzed by grazing incidence X-ray diffraction and revealed the amorphous phase for IZO samples, while the AZO thin films inherited the Wurtzite structure of zinc oxide. The morphological properties were investigated by atomic force microscopy (AFM), in tapping mode and scanning electronmicroscopy (SEM). The AFM images showed relatively uniform and smooth surfaces for all prepared structures. The optical transmission spectra proved the excellent theoretical values of transparency for metallic oxides in the visible region of the electromagnetic spectrum, i.e. similar to 60% for IZO and similar to 70% for AZO. The obtained results showed that even without any thermal treatment the structural, morphological, and optical properties of IZO and AZO thin films prepared by RF magnetron sputtering are similar with those for samples subjected to medium or high temperatures.