Publications

This paper presents an evaluation regarding the influence of substrate material characteristics and deposition parameters on the tribological behaviour of carbon-based coatings. Chromium nitride ceramic interlayers and carbon-based thin films were deposited by magnetron sputtering on hardened AISI 5115 (16MnCr5) case hardening steel. The physical vapour deposition (PVD) deposition was performed at three different temperatures: 180 degrees C, 200 degrees C and 250 degrees C. The chemical composition of the samples was assessed by Rutherford Backscattering Spectroscopy (RBS), the structure by X-ray Diffraction (XRD), and the surface morphology by Atomic Force Microscopy (AFM). The surface chemistry was analysed by X-ray Photoelectron Spectroscopy (XPS) and Raman Spectroscopy. The coatings are homogeneous, amorphous, with a smooth surface. The mechanical behaviour has been assessed on a pin-on disk rotational tribometer (wear characteristics), on a micro scratch tester (adhesion to the substrate), by ball-cratering (film thickness) and by nanoindentation (hardness and the modulus of elasticity). A strong correlation has been observed between the substrate characteristics and, more importantly, the deposition temperature, and the mechanical properties of the assembly. The fracture toughness is positively influenced by the presence of the ceramic chromium nitride interlayer. The modulus of elasticity and friction coefficient (both in dry and lubricated conditions) are decreased for higher deposition temperatures, however the higher deposition temperature negatively affects the mechanical characteristics of the steel substrate.

Technologically relevant tetragonal/cubic phases of HfO2 can be stabilized at room temperature by doping with trivalent rare earths using various approaches denoted generically as bulk coprecipitation. Using in situ/ex situ X-ray diffraction (XRD), Raman spectroscopy, high-resolution transmission electron microscopy, and in situ/ex situ site-selective, time-gated luminescence spectroscopy, we show that wet impregnation of hafnia nanoparticles with 10% Eu oxide followed by mild calcination in air at 500 degrees C produces an efficient stabilization of the cubic phase, comparable to that obtained by bulk precipitation. The physical reasons behind the apparently conflictual data concerning the actual crystallographic phase and the local symmetry around the Eu stabilizer and how these can be mediated by luminescence analysis are also discussed. Apparently, the cubic crystal structure symmetry determined by XRD results in a pseudocubic/tetragonal local structure around Eu determined by luminescence. Considering the recent findings on wet impregnated CeO2 and ZrO2, it is concluded that CeO2, ZrO2, and HfO2 represent a unique case of a family of oxides that is extremely tolerant to heavy doping by wet impregnation. In this way, the same batch of preformed nanoparticles can be doped with different lanthanide concentrations or with various lanthanides at a fixed concentration, allowing a systematic and reliable investigation of the effect of doping, lanthanide type, and lanthanide concentration on the various functionalities of these technologically relevant oxides.

The efficiency of the Organic Light Emitting Diode (OLED) is given either by the internal quantum efficiency of the organometallic compound or by the charge transport across OLED. IrQ(ppy)(2) is a new organometallic compound which gives green and red electroluminescence. This dual emitter compound exhibits a lower internal quantum efficiency compared with classical Ir(ppy)(3) green emitter because of a weak coupling between Ir3+ and oxygen ions which significantly reduces the charge transfer towards quinoline ligand. This lower internal quantum efficiency is compensated by the higher electron donor character of the quinoline ligand which induces better change transport in OLED structures. In the case of Ir(ppy)(3) green emitter, the efficiency can be improved by adding magnetic or metallic nanoparticles which significantly change the charge transport for the Ir(ppy)(3) based OLED structures. The metallic or magnetic nanoparticles embedded in the transparent and conductive polymer, reduce the electron injection, acting as filling traps, which directly increases the electroluminescence and the current at the same voltage.

A hard templating method, using SBA-15 in combination with glucose solution and different heteroatom precursors, has been employed to investigate the influence of the different heteroatom dopants nitrogen, boron, sulfur, and phosphorus on carbon electrocatalysts for the oxygen reduction reaction. Samples were synthesized under the same conditions and resulted in a similar morphology and surface areas around 1000 m(2)/g. Incorporating nitrogen into the carbon matrix was found to be easier than for boron or phosphorus, while sulfur doping proved problematic and only yielded 2 at% of sulfur or less. Different dopant concentrations as well as a combination of dopants suggested that nitrogen was the only heteroatom exerting an actual influence on the catalytic activity, resulting in higher electron transfer numbers. The other dopants exhibited a similar performance regardless of the dopant content, though slightly improved when compared to an undoped control sample. These findings indicate that incorporated nitrogen can act as catalytic sites, while boron, sulfur and phosphorus can enhance the catalytic activity by possibly creating defects in the carbon matrix.

Dextran-coated zinc-doped hydroxyapatite (ZnHApD) was synthesized by an adapted sol-gel method. The stability of ZnHApD nanoparticles in an aqueous solution was analyzed using ultrasonic measurements. The analysis of the evolution in time of the attenuation for each of the frequencies was performed. The X-ray diffraction (XRD) investigations exhibited that no impurity was found. The morphology, size and size distribution of the ZnHApD sample was investigated by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The TEM and SEM results showed that the ZnHApD particles have an ellipsoidal shape and a narrow distribution of sizes. The cell growth and toxicity of HEK-293 cells were investigated on the ZnHApD solution for four different concentrations and analyzed after 24 and 48 h. The ZnHApD solution presented a non-toxic activity against HEK-293 cells for all analyzed concentrations. The antibacterial assay revealed that all the tested microorganisms were inhibited by the ZnHApD dispersion after 24 and 48 h of incubation. It was observed that the effect of the ZnHApD solution on bacteria growth depended on the bacterial strain. The Porphyromonas gingivalis ATCC 33277 bacterial strain was the most sensitive, as a growth inhibition in the presence of 0.075 mu g/mL ZnHApD in the culture medium was observed.

We report the structural, dielectric, elastic, ferroelectric and ferromagnetic properties of multiferroic (Nd, Fe)doped PbTiO3 perovskite ceramics with composition (Pb-0.88 Nd-0.08 )(Ti-0.94 Fe-0 .04 Mn-0.02)O-3, prepared by different solid state reaction methods: the first one based on a single-stage calcination (Method I) and the second based on a double-stage calcination (Method II). Structural, dielectric and anelastic measurements evidenced a double phase transition for samples prepared by Method I, which has been attributed to phase separation. This phase separation has been confirmed also by TEM and HRTEM investigations. Samples prepared by Method II showed a single phase transition from paraelectric to ferroelectric phase. We found coexistent ferroelectric and ferromagnetic properties, also at room-temperature, but only for ceramics prepared by Method II. The crucial role of calcination process for avoiding phase separation and obtaining homogeneous structures with ferroelectric and ferromagnetic order is underlined.

We report studies of quasi-remanent polarization states in Pb0.99Nb0.02[(Zr0.57Sn0.43)(0.94)Ti-0.06](0.98)O-3 (PNZST) anti-ferroelectric ceramics and investigation of their relaxation effects using unique in-situ electrically activated time-resolved Synchrotron X-ray powder diffraction (SXPD) and Sn-119 Mossbauer Spectroscopy (MS). The SXPD patterns are consistent with a phase transition from quasi-tetragonal perovskite in 0 V relaxed anti-ferroelectric state to rhombohedral distortion in ferroelectric state under saturating applied voltages of +/- 2 kV. The observed quasi-remanent polarization relaxation processes are due to the fact that tetragonal to rhombohedral distortion does not occur at the applied voltage required to access the quasiremanent polarization states, and the tetragonal symmetry restored after the removal of the applied electric field is preserved. Since these quasi-remanent polarization states were seen as possibly suitable for memory applications, the implications of this study are that anti-ferroelectrics are more feasible for multi-state dynamic random access memories (DRAM), while their application to non-volatile memories requires development of more sophisticated "read-out" protocols, possibly involving dc electrical biasing.

We report on the fabrication of dye-sensitized solar cells with a TiO2 buffer layer between the transparent conductive oxide substrate and the mesoporous TiO2 film, in order to improve the photovoltaic conversion efficiency of the device. The buffer layer was fabricated by pulsed laser deposition whereas the mesoporous film by the doctor blade method, using TiO2 paste obtained by the sol-gel technique. The buffer layer was deposited in either oxygen (10 Pa and 50 Pa) or argon (10 Pa and 50 Pa) onto transparent conducting oxide glass kept at room temperature. The cross-section scanning electron microscopy image showed differences in layer morphology and thickness, depending on the deposition conditions. Transmission electron microscopy studies of the TiO2 buffer layers indicated that films consisted of grains with typical diameters of 10 nm to 30 nm. We found that the photovoltaic conversion efficiencies, determined under standard air mass 1.5 global (AM 1.5G) conditions, of the solar cells with a buffer layer are more than two times larger than those of the standard cells. The best performance was reached for buffer layers deposited at 10 Pa O-2. We discuss the processes that take place in the device and emphasize the role of the brush-like buffer layer in the performance increase.

1-D coordination polymers, (1)(infinity)[Zn(fl)(2)]center dot 2EtOH and (1)(infinity)[Zn(fl)(2)]center dot 2MeOH, and a dinuclear complex, [{Zn(fl)(2)}(2)(dienpip)]center dot 4H(2)O center dot 4EtOH (dienpip= N,N '-bis(2-aminoethyl)piperazine), were obtained using Zn(II) ions and fluorescein anions (fl). Thermal analysis shows stability of the polymers after solvent removal up to more than 400 degrees C. Crystallization solvent molecules were removed under reduced pressure with the preservation of the polymeric structure, (1)(infinity)[Zn(fl)(2)]. Desolvated crystals were exposed to I-2 vapors and the crystal structure determination by X-ray diffraction confirmed the presence of I-2 molecules in the channels generated in crystals by the metal-organic framework. The iodine content, evaluated by X-ray diffraction, corresponds to the overall formula (1)(infinity)[Zn(fl)(2)]center dot 0.3I(2). The optical properties of the coordination polymers and the dinuclear complex have been investigated. [GRAPHICS] .

Ruthenium-doped copper ferrite(Ru - CuFe2O4) nanoparticles (NPs) have been synthesized using a simple and cost-effective wet chemical co-precipitation deposition method. The crystallographic scanning electron microscopy images confirm cubic crystal structure and agglomerated-type surface appearance. The crystallite sizes are 6-24 nm in the range. Dielectric measurement analysis estimates the dielectric constant and loss of Ru - CuFe2O4 NPs. In this connection, dielectric constant and loss are reduced virtue of air annealing for various temperatures. Also, the dielectric loss confirms the relaxation peak. From magnetic measurement results, the coercivity decreases whereas saturation and remanence magnetization are increased. These features have approved the soft magnetic nature in the Ru - CuFe2O4 NPs.