National Institute Of Materials Physics - Romania

We report in this paper on the monolayer composites thin films that have the magnetic spinel CoFe2O4 and the piezoelectric perovskite BNT-BT0.08 as constituent phases. Composite thin films of CoFe2O4 and BNT-BT0.08, with molar ratios of 0.5:1, 1:1 and 1.5:1, have been deposited by spin coating method from a sol precursor, mixture type, of CoFe2O4 and BNT-BT0.08. The monolayer thin films, deposited on Si/SiO2/TiO2/Pt substrate, were characterized using selected methods, such as: X-ray diffraction, scanning electron microscopy, atomic force microscopy/piezoelectric force microscopy, dielectric spectroscopy, and vibrating sample magnetometer. X-ray diffraction demonstrated the two phases: cubic CoFe2O4 and rhombohedral BNT-BT0.08. Furthermore, the Si/ SiO2/TiO2/Pt/BNT-BT0.08/CoFe2O4 monolayers show a simultaneous enhancement of both the magnetization and coercivity with the increase of the magnetic phase, accompanied by a decrease of the dielectric constant. The obtained results reveal that the investigated monolayer structures present superior properties compared to those of bilayer composites.

In this work, we report the preparation of nanostructured electrodes based on dense arrays of vertically-aligned copper (Cu) nanowires (NWs) to be subsequently covered by cadmium telluride (CdTe) thin films, with great potential to be used within "substrate"-type photovoltaic cells based on A(II)-BVI heterojunctions. In particular, the multi-step preparation protocol presented here involves an electrochemical synthesis procedure within a supported anodic aluminum oxide (AAO) nanoporous template for first generating a homogeneous array of vertically-aligned Cu NWs, which are then further embedded within a compact CdTe thin film. In a second stage, we tested three deposition methods (vacuum thermal evaporation, VTE; radio-frequency magnetron sputtering, RF-MS; and electrochemical deposition, ECD) for use in obtaining CdTe layers potentially able to consistently penetrate the previously prepared Cu NWs array. A comparative analysis was performed to critically evaluate the morphological, optical, and structural properties of the deposited CdTe films. The presented results demonstrate that under optimized processing conditions, the ECD approach could potentially allow the cost-effective fabrication of absorber layer/collecting electrode CdTe/Cu nanostructured interfaces that could improve charge collection mechanisms, which in turn could allow the fabrication of more efficient solar cells based on A(II)-BVI semiconducting compounds.

Direct current (DC) and radio frequency (RF) magnetron sputtering methods were selected for conducting the deposition of structural materials, namely ceramic and metallic co-depositions. A total of six configurations were deposited: single thin layers of oxides (Cr2O3, SiO2) and co-deposition configurations (50:50 wt.%) as structural materials (W, Be)-(Cr2O3, SiO2), all deposited on 304L stainless steel (SS). A comprehensive evaluation such as surface topology, thermal desorption outgassing, and structural/chemical state was performed. Moreover, mechanical characterization evaluating properties such as adherence, nano indentation hardness, indentation modulus, and deformation relative to yielding, was performed. Experimental results show that, contrary to SiO2 matrix, the composite layers of Cr2O3 with Be and W exhibit surface smoothing with mitigation of artifacts, thus presenting a uniform and compact state with the best microstructure. These results are relevant in order to develop future dense coatings to be used in the fusion domain.

This is the first report regarding the effect of gamma irradiation on chitosan-coated magnesium-doped hydroxyapatite (x(Mg) = 0.1; 10 MgHApCh) layers prepared by the spin-coating process. The stability of the resulting 10 MgHApCh gel suspension used to obtain the layers has been shown by ultrasound measurements. The presence of magnesium and the effect of the irradiation process on the studied samples were shown by X-ray photoelectron spectroscopy (XPS). The XPS results obtained for irradiated 10 MgHApCh layers suggested that the magnesium and calcium contained in the surface layer are from tricalcium phosphate (TCP; Ca-3(PO4)(2)) and hydroxyapatite (HAp). The XPS analysis has also highlighted that the amount of TCP in the surface layer increased with the irradiation dose. The energy-dispersive X-ray spectroscopy (EDX) evaluation showed that the calcium decreases with the increase in the irradiation dose. In addition, a decrease in crystallinity and crystallite size was highlighted after irradiation. By atomic force microscopy (AFM) we have obtained images suggesting a good homogeneity of the surface of the non-irradiated and irradiated layers. The AFM results were also sustained by the scanning electron microscopy (SEM) images obtained for the studied samples. The effect of gamma-ray doses on the Fourier transform infrared spectroscopy (ATR-FTIR) spectra of 10 MgHApCh composite layers was also evaluated. The in vitro antifungal assays proved that 10 MgHApCh composite layers presented a strong antifungal effect, correlated with the irradiation dose and incubation time. The study of the stability of the 10 MgHApCh gel allowed us to achieve uniform and homogeneous layers that could be used in different biomedical applications.

Gallium telluride (GaTe) is a van der Waals semiconductor, currently adopted for photonic and optoelectronic devices. However, the rapid degradation of GaTe in air, promoted by Te vacancies, is detrimental for device applications. Here, it is demonstrate that the surface oxidation of GaTe can be unexpectedly exploited for expanding the breadth of applications of GaTe. Specifically, the formation of a nanoscale sub-stoichiometric wide-band-gap Ga2O3 skin, promoted by Te vacancies, over narrow-band-gap GaTex upon air exposure is beneficial for electrocatalysis, photocatalysis, and gas sensing . In particular, the Heyrovsky step (H-ads + H+ + e(-) -> H-2) of hydrogen evolution reaction in an acidic medium is barrier-free for the sub-stoichiometric gallium-oxide/gallium-telluride heterostructure, which also enables a significant reduction of costs with respect to state-of-the-art Pt/C electrodes. In the photocatalytic process, the photo-generated electrons migrate from GaTe to Ga2Ox skin, which acts as the chemically active side of the interface. Moreover, the Ga2O3/GaTe heterostructure is a suitable platform for sensing of H2O, NH3, and NO2 at operational temperatures extended up to 600 degrees C (useful for gas detection in combustion processes), mainly due to the increased area of charge redistribution after adsorption achieved upon oxidation of GaTe.

Electrospun polymeric fibers present an emerging alternative for the development of flexible electronics, enabling applications in wearable sensors and biosensors for continuous monitoring, and actuators for tissue engineering. The possibility to prepare sub-micrometric polymeric scaffolds, their processing for increasing the conductivity, their modification with different materials, conductive polymers and biomolecules in order to obtain functional flexible electrodes, allows the development of innovative devices for healthcare, and biomedical applications. In this review, the impact of metallized electrospun polymeric fibers in electrochemical (bio)sensors and actuators is discussed. A relation between their structure and functionality is provided, alongside with an overview of the different methods to obtain functional conductive fibers.

The paper presents fabrication and characterization of spark plasma sintered textured (001) MgB2 with a record degree of orientation of about 40% and 16% by high-energy ultra-sonication and slip casting in high magnetic field (12 T) and 0 T magnetic field, respectively. Structural characterization was performed by X-ray diffraction, and electron microscopy. The analysis revealed unexpected preferred orientation also in the MgO secondary phase due to the epitaxial growth of (111) MgO on (001) MgB2. The influence of oriented microstructure on the superconducting characteristics expressed by critical current density (Jc), irreversibility field ( H irr), and on the pinning properties were assessed. High anisotropy versus sample orientation in applied magnetic field, H , was observed for Jc, Hirr, pinning activation energy ( U *) extracted from relaxation measurements. The zero-field critical current, Jc0 and Fp,maxare weakly or not dependent on the direction of H , while the other indicated parameters are significantly influenced. Results enable control of superconducting parameters by further optimization of microstructure through MgB2 texturing as a novel and viable strategy for development of bulk MgB2 with enhanced properties when taking advantage of its anisotropy.(c) 2021 Chongqing University. Publishing services provided by Elsevier B.V. on behalf of KeAi Communications Co. Ltd. This is an open access article under the CC BY-NC-ND license ( http://creativecommons.org/licenses/by-nc-nd/4.0/ ) Peer review under responsibility of Chongqing University

ZnO nanostructures were electrochemically synthesized on Cu and on chemical vapor deposited (CVD)-graphene/Cu electrodes. The deposition was performed at different electrode potentials ranging from -0.8 to -1.2 V, employing a zinc nitrate bath, and using voltametric and chronoamperometric techniques. The effects of the electrode nature and of the working electrode potential on the structural, morphological, and optical properties of the ZnO structures were investigated. It was found that all the samples crystallize in hexagonal wurtzite structure with a preferential orientation along the c-axis. Scanning electron microscopy (SEM) images confirm that the presence of a graphene covered electrode led to the formation of ZnO nanowires with a smaller diameter compared with the deposition directly on copper surface. The photoluminescence (PL) measurements revealed that the ZnO nanowires grown on graphene/Cu exhibit stronger emission compared to the nanowires grown on Cu. The obtained results add another possibility of tailoring the properties of such nanostructured films according to the specific functionality required.