National Institute Of Materials Physics - Romania

The microcrystallization effects induced by the real-time laser annealing in Cr-Al-C ion-sputtered films with an off-stoichiometric composition are studied. The laser annealing has been performed during Raman experiments with tunable laser power densities. Morphostructural changes induced during laser annealing were investigated by scanning electron microscopy. It has been proven that real-time laser annealing in the high-laser-power-density mode promotes quite clearly the formation of nanograins through surface microcrystallization. Detailed Raman analysis allowed for the observation of the optical modes that unequivocally identifies the low-symmetry 211 MAX phase in both low- and high-power-density modes. Such findings confirming the microcrystallization as well as the stabilization of the grain boundaries by carbon nanoclustering are confirmed by X-ray diffraction results, where the single-phase hexagonal 211 was unequivocally proven to form in the high-laser-power-density mode. The microcrystallization via laser annealing was also found to be beneficial for the elastic behavior, as the hardness values between 16 and 26 GPa were found after laser annealing, accompanied by a significantly high Young's bulk modulus. Such large values, larger than those in bulk compounds, are explicable by the nanometric grain sizes accompanied by the increase of the grain boundary regions.

The properties of organic heterostructures with mixed layers made of arylenevinylene-based polymer donor and non-fullerene perylene diimide acceptor, deposited using Matrix Assisted Pulsed Laser Evaporation on flat Al and nano-patterned Al electrodes, were investigated. The Al layer electrode deposited on the 2D array of cylindrical nanostructures with a periodicity of 1.1 mu m, developed in a polymeric layer using UV-Nanoimprint Lithography, is characterized by an inflorescence-like morphology. The effect of the nanostructuring on the optical and electrical properties was studied by comparison with those of the heterostructures based on a mixed layer with fullerene derivative acceptor. The low roughness of the mixed layer deposited on flat Al was associated with high reflectance. The nano-patterning, which was preserved in the mixed layer, determining the light trapping by multiple scattering, correlated with the high roughness and led to lower reflectance. A decrease was also revealed in photoluminescence emission both at UV and Vis excitation of the mixed layer, with the non-fullerene acceptor deposited on nano-patterned Al. An injector contact behavior was highlighted for all Al/mixed layer/ITO heterostructures by I-V characteristics in dark. The current increased, independently of acceptor (fullerene or non-fullerene), in the heterostructures with nano-patterned Al electrodes for shorter conjugation length polymer donors.

The structural properties of VO2 thin films, grown on either LSAT or Si substrates by pulsed laser deposition (PLD), are elucidated by means of transmission electron microscopy (TEM) methods. The TEM observations confirmed the successful growth of VO2 by PLD in variable thicknesses, by optimizing the O-2 partial pressure and growth temperature. The films adopt a columnar polycrystalline morphology with narrow columns, up to the film thickness height. Four VO2 polymorphs have been detected by electron diffraction and high-resolution TEM (HRTEM) analysis, with M1 being by far the most abundant phase. Post-experimental strain measurements in HRTEM images have revealed that the actual residual strain is minimized due to the columnar morphology of the VO2 grains, as well as intrinsic oxide layers in the VO2/Si epitaxy. The TEM outcomes confirmed the complementary electrical and magnetic measurements in the films, where a transition from a monoclinic M1 to a rutile VO2 R phase has been identified, influenced by the initial percentage of phases in thick VO2 films.

We have investigated the pinning potential of high-quality single crystals of superconducting material CaKFe4As4 having high critical current density and very high upper critical field using both magnetization relaxation measurements and frequency-dependent AC susceptibility. Preliminary studies of the superconducting transition and of the isothermal magnetization loops confirmed the high quality of the samples, while temperature dependence of the AC susceptibility in high magnetic fields show absolutely no dependence on the cooling conditions, hence, no magnetic history. From magnetization relaxation measurements were extracted the values of the normalized pinning potential U*, which reveals a clear crossover between elastic creep and plastic creep. The extremely high values of U*, up to 1200 K around the temperature of 20 K lead to a nearly zero value of the probability of thermally-activated flux jumps at temperatures of interest for high-field applications. The values of the creep exponents in the two creep regimes resulted from the analysis of the magnetization relaxation data are in complete agreement with theoretical models. Pinning potentials were also estimated, near the critical temperature, from AC susceptibility measurements, their values being close to those resulted (at the same temperature and DC field) from the magnetization relaxation data.

The chemical precipitation was used to obtain carbon fibers (CF) with surface modified by magnetite particles (Fe3O4). Processing was carried out by employing up to three subsequent coating stages of ultrasonic treatments. After each sonication stage, the coating was 17, 33, and 47 wt. % of the total weight of the modified fibers. Raman spectroscopy indicates the presence in the coating of a mixture of iron II and III states. As-decorated fibers were used to fabricate composites with an epoxy resin (ED-20) matrix cured with PEPA. The quantity of the carbon fiber filler was of 1, 3, and 6 wt %. At room temperature, the saturation magnetization of the soft magnetic samples was 0.37, 0.83, and 1.72 emu/g for the indicated compositions. Carbon fiber reinforced polymer materials with extra functions such as magnetic in this case, are expected to be useful in applications from the power and energy industries.

Polycrystalline MgB2 bulk samples were produced by ex-situ spark plasma sintering (SPS) using the oxygen-free preceramic polymer additive poly(dimethylsilane) as a source for carbon doping and as a sintering aid. Two major effects were identified. One is the significant enhancement of the densification kinetics during sintering for all tested compositions. The second one is the improvement of the high field critical current density for a certain level of the poly(dimethylsilane) addition.

In the present work, stannite Cu2CoSnS4 (CCTS) films were elaborated using spray pyrolysis method on soda-lime glass, at different deposition temperatures (T-d = 250, 300, and 350 degrees C), followed by different chosen sulfurization temperatures (T-s = 450, 500, and 550 degrees C). X-ray diffraction (XRD) revealed the nearly single-phase formation of CCTS films at 300 degrees C deposition temperature. After sulfurization in argon flow, the XRD lines become narrower, the average crystallite size expanding above 70 nm. The Raman spectroscopy analysis confirmed the stannite structure formation, as well as the presence CoS2 secondary phases, which reduces at higher sulfurization temperature (550 degrees C). The energy dispersive spectroscopy results indicated atomic ratios of Cu/Co/Sn/S close to the ideal stoichiometric ratio 2:1:1:4. The room temperature photoluminescence emission is recorded with maximum in the 1.35-1.40 eV range. Thermoelectric properties are measured up to 130 degrees C, the films show poor power factor as a result of small positive Seebeck coefficients 10-45 Of K -1 and low electrical conductivity despite of having relatively high carrier concentration (similar to 10(20) cm(-3)).

In this study, two alternative synthesis routes have been used in obtaining gas-sensitive NiO materials. The structural and morphological aspects were systematically investigated by X-ray diffraction (XRD) and transmission electron microscopy (TEM), revealing significant differences further mirrored in their sensing performances. Simultaneous electrical resistance and contact potential differences have been involved aiming to decouple the energetic contributions: work function (Delta phi), surface band bending (q Delta Vs) and electron affinity (Delta chi). Two sensing mechanism scenarios explained the enhancement and downgrading in the sensor response to carbon monoxide (CO) concerning the synthesis strategies. The role of relative humidity (RH) was considered throughout the electrical operando (in-field) investigations.

This work explores the possibility of involving aluminothermy in processing donor-doped zinc oxide-based thermoelectrics by relying on local, strong exothermic effects developed during sintering, with a potential positive impact on the electrical and thermal transport properties. The strategy was exemplified by using aluminium as a dopant, due to its recognized ability to generate additional, available charge carriers in ZnO, and by using two different metallic Al powders and conventional Al2O3 as precursors. Nanosized aluminium powder was involved in order to evaluate the possible desirable effects of the particles size, as compared to aluminium micropowder. A significant enhancement of the electrical and thermoelectric performance of the samples prepared via metallic Al precursors was observed and discussed in terms of the potential impacts provided by the aluminothermic reaction on the microstructure, charge carrier concentration and mobility during sintering. Although the presented results are the first to show evidence of how aluminothermic reactions can be used for boosting the thermoelectric performance of zinc oxide materials, the detailed mechanisms behind the observed enhancements are yet to be understood.

The present work reports the synthesis and characterization of polycaprolactone fibers loaded with particulate calcium magnesium silicates, to form composite materials with bioresorbable and bioactive properties. The inorganic powders were achieved through a sol-gel method, starting from the compositions of diopside, akermanite, and merwinite, three mineral phases with suitable features for the field of hard tissue engineering. The fibrous composites were fabricated by electrospinning polymeric solutions with a content of 16% polycaprolactone and 5 or 10% inorganic powder. The physico-chemical evaluation from compositional and morphological points of view was followed by the biological assessment of powder bioactivity and scaffold biocompatibility. SEM investigation highlighted a significant reduction in fiber diameter, from around 3 mu m to less than 100 nm after the loading stage, while EDX and FTIR spectra confirmed the existence of embedded mineral entities. The silicate phases were found be highly bioactive after 4 weeks of immersion in SBF, enriching the potential of the polymeric host that provides only biocompatibility and bioresorbability. Moreover, the cellular tests indicated a slight decrease in cell viability over the short-term, a compromise that can be accepted if the overall benefits of such multifunctional composites are considered.