Publications

In this work, Tungsten(W)-doped TiO2 nanoparticles were synthesized using the sol-gel method and were used as electrode materials in supercapacitor applications. The structural and morphological properties of the prepared samples were analyzed by means of XRD, STEM, TEM, and XPS. The analysis of the defect centers was carried out using EPR spectroscopy. The electrochemical analysis of the assembled supercapacitor was done using cyclic voltammetry, galvanostatic cycling with potential limitation technique, potentiostatic electrochemical impedance spectroscopy, and voltage-holding experiments. All the presented samples showed paramagnetic defects in the EPR analysis, while 0.5% W-doped TiO2 showed a maximum signal intensity. The supercapacitor performance from the synthesized electrode material showed highly encouraging results. The equivalent series resistance (R-s) value for all the designs showed values under "1 omega,' which reflects high conductivity. As the maximum EPR intensity comes from TiO2 doped with 0.5% W, the supercapacitor performance of this sample was tested with a newly designed five-electrode system. This design showed superior performance compared to any other used designs with a specific capacitance of 25.5 F g(-1), with an energy density of 14.16 Wh kg (-1 )at 302 kW kg (-1).

Glassy nanocomposites containing Yb3+/Er3+-doped GdF3 and LiGdF4 nanocrystals have been prepared by controlled crystallization of the xerogel and the structural, up-conversion luminescence, and magnetic properties were analyzed and discussed. Structural and morphological analysis showed uniform distribution of both GdF3 and LiGdF4 nanocrystals (tens of nm size), embedded in silica glass matrix as the result of thermal decomposition of the trifluoracetates, revealed as a strong exothermic peak at about 300 degrees C; the Li-ions co-doping showed a strong influence on the GdF3 and LiGdF4 nanocrystalline fraction. The energy dispersive spectrometry mapping showed Gd, F and Yb, Er within the nanocrystals but not in the silica glass matrix. X-ray diffraction pattern analysis indicated the crystalline lattice distortion consistent with the Yb/Er incorporation in both fluoride nanocrystals. The "green" ((H-2(11/2), S-4(3/2)) -> I-4(15/2)) and "red" (F-4(9/2)-> I-4(15/2)) up-conversion luminescences at 525, 545, and 660 nm observed under 980 nm laser light pumping were assigned to the Er3+ ions deexcitation through a two-photon process. The magnetic properties of the nanocomposite are strongly temperature dependent. The magnetization hysteresis loops show a ferromagnetic behavior at low temperatures (5K) related to the rare-earth ions contribution and the saturation magnetization of 39 emu/g. At 300 K a paramagnetic behavior was observed that was ascribed to the non-interacting localized nature of the magnetic moment of the rare-earth ions. Hence, such novel, multifunctional magnetic and optical materials can allow the intertwining between magnetism and photonics and might offer new opportunities for new magneto-optical device development.

In our work, the kinetics of martensitic transformations and the influence of thermal treatments on martensitic transformations, as well as the related magnetic properties of the Ni49Mn32Ga19 ferromagnetic shape memory melt-spun ribbons, have been investigated. Thermal treatments at 673 K for 1, 4 and 8 h can be considered an instrument for fine-tuning the performance parameters of alloys. One-hour thermal treatments promote an improvement in the crystallinity of these otherwise highly textured ribbons, reducing internal defects and stress induced by the melt-spinning technique. Longer thermal treatments induce an important magnetization rise concomitantly with a slight and continuous increase in martensitic temperatures and transformation enthalpy. The activation energy, evaluated from differential scanning calorimeter experimental data with a Friedman model, significantly increases after thermal treatments as a result of the multi-phase coexistence and stabilization of the non-modulated martensitic phase, which increases the reverse martensitic transformation hindrance.

Featuring a high hydrogen storage content of up to 20 wt%, complex metal borohydrides remain promising solid state hydrogen storage materials, with the real prospect of reversible behavior for a zero-emission economy. However, the thermodynamic barriers and sluggish kinetics are still barriers to overcome. In this context, nanoconfinement has provided a reliable method to improve the behavior of hydrogen storage materials. The present work describes the thermodynamic and kinetic enhancements of LiBH4 nanoconfined in MFe2O4 (M=Co, Ni) ferrite-catalyzed graphene host. Composites of LiBH4-catalysts were prepared by melt infiltration and investigated by X-ray diffraction, TEM, STEM-EDS and TPD. The role of ferrite additives, metal precursor treatment (Ar, Ar/H-2) and the effect on hydrogen storage parameters are discussed. The thermodynamic parameters for the most promising composite LiBH4-graphene-NiFe2O4 (Ar) were investigated by Kissinger plot method, revealing an E-A = 127 kJ/mol, significantly lower than that of neat LiBH4 (170 kJ/mol). The reversible H-2 content of LiBH4-graphene-NiFe2O4 (Ar) after 5 a/d cycles was similar to 6.14 wt%, in line with DOE's target of 5.5 wt% storage capacity, while exhibiting the lowest desorption temperature peak of 349 degrees C. The composites with catalysts treated in Ar have lower desorption temperature due to better catalyst dispersion than using H-2/Ar.

The p-n junctions are the building blocks of nowadays electronic devices. The n- or p-type conductivity is obtained in classic semiconductors, like Si, by doping with atoms acting as donors or acceptors, respectively. Doping was used in ferroelectrics to influence the transition temperature, magnitude of some physical properties, but not necessarily conduction type. Therefore, comprehensive studies to obtain true ferroelectric p-n junctions by controlled doping are missing. Recently, it has been shown that Pb(Zr0.2Ti0.8)O-3 films doped with & AP;1% atomic Nb (n-type doping) or Fe (p-type doping) have different orientations of polarization in the as-grown state. Knowing that polarization orientation depends on doping type, the next step is to build ferroelectric p-n homojunctions and to study their properties in relation to ferroelectric polarization. p-n and n-p structures were grown for this purpose by successive deposition of Nb-doped and Fe-doped Pb(Zr,Ti)O-3 layers with different thicknesses. We find that these p-n homojunctions are ferroelectric, but the magnitude of the polarization and coercive field, as well as the dominant polarization orientation in the as-grown state, depend on the conduction type of the first grown layer. The I-V characteristics are quasi-linear, although the interfaces with the electrodes behaves as Schottky contacts. The resistance extracted from the I-V characteristics displays an exponential dependence on temperature, with an activation energy in the range of 0.14-0.17 eV. These results are explained assuming that the total current in the junction is the total of electron and hole injections at the electrode interfaces. It is shown that for relatively low doping concentrations, the current density contains a dominant term with a linear voltage dependence and an exponential temperature dependence, as observed experimentally, and a secondary (correction) term that is dependent on the free carrier density and can induce non-linear voltage dependence when this density is significant.

The treatment of wounds occurring accidentally or as a result of chronic diseases most frequently requires the use of appropriate dressings, mainly to ensure tissue regeneration/healing, at the same time as treating or preventing potential bacterial infections or superinfections. Collagen type I-based scaffolds in tandem with adequate antimicrobials can successfully fulfill these requirements. In this work, starting from the corresponding hydrogels, we prepared a series of freeze-dried atelocollagen type I-based matrices loaded with tannic acid (TA) and chlorhexidine digluconate (CHDG) as active agents with a broad spectrum of antimicrobial activity and also as crosslinkers for the collagen network. The primary aim of this study was to design an original and reliable algorithm to in vitro monitor and kinetically analyze the simultaneous release of TA and CHDG from the porous matrices into an aqueous solution of phosphate-buffered saline (PBS, pH 7.4, 37 degrees C) containing micellar carriers of a cationic surfactant (hexadecyltrimethylammonium bromide, HTAB) as a release environment that roughly mimics human extracellular fluids in living tissues. Around this central idea, a comprehensive investigation of the lyophilized matrices (morpho-structural characterization through FT-IR spectroscopy, scanning electron microscopy, swelling behavior, resistance against the collagenolytic action of collagenase type I) was carried out. The kinetic treatment of the release data displayed a preponderance of non-Fickian-Case II diffusion behavior, which led to a general anomalous transport mechanism for both TA and CHDG, irrespective of their concentrations. This is equivalent to saying that the release regime is not governed only by the gradient concentration of the releasing components inside and outside the matrix (like in ideal Fickian diffusion), but also, to a large extent, by the relaxation phenomena of the collagen network (determined, in turn, by its crosslinking degree induced by TA and CHDG) and the dynamic capacity of the HTAB micelles to solubilize the two antimicrobials. By controlling the degree of physical crosslinking of collagen with a proper content of TA and CHDG loaded in the matrix, a tunable, sustainable release profile can be obtained.

Lately, there is a growing interest in organic photovoltaic (OPV) cells due to the organic materials' properties and compatibility with various types of substrates. However, their efficiencies are low relative to the silicon ones; therefore, other ways (i.e., electrode micron/nanostructuring, synthesis of new organic materials, use of additives) to improve their performances are still being sought. In this context, we studied the behavior of the common organic bulk heterojunction (P3HT:PC70BM) deposited by matrix-assisted pulsed laser evaporation (MAPLE) with/without 0.3% of 1,8-diiodooctane (DIO) additive on flat and micro-patterned ITO substrates. The obtained results showed that in the MAPLE process, a small quantity of additive can modify the morphology of the organic films and decrease their roughness. Besides the use of the additive, the micro-patterning of the electrode leads to a greater increase in the absorption of the studied photovoltaic structures. The inferred values of the filling factors for the measured cells in ambient conditions range from 19% for the photovoltaic structures with no additive and without substrate patterning to 27% for the counterpart structures with patterning and a small quantity of additive.

We present the multifrequency measurements of the surface resistance of spark-plasma-sintered MgB2 performed through a dielectric loaded resonator operating at 16.5 and 26.7 GHz. By normally applying magnetic fields <= 1.2 T to the sample surface, we drove it in the mixed state. By means of data-rooted analysis, we found that the sample vortex dynamics could be fully described within a single-component approach. Pinning phenomena were present and characterized by a depinning frequency smaller than the measurement ones. The multiband nature of the superconductor emerged in the flux-flow resistivity, whose field dependence could be interpreted well within theoretical models. By exploiting them, the upper critical field was extracted in the low-temperature range, which exhibited a consistent temperature trend with the values obtained at the onset of the resistive transition near Tc, and was well in line with literature data on other polycrystalline samples.

In this article, we review recent progress concerning the development of sensorial platforms based on graphene derivatives and conducting polymers (CPs), alternatively deposited or co-deposited on the working electrode (usually a glassy carbon electrode; GCE) using a simple potentiostatic method (often cyclic voltammetry; CV), possibly followed by the deposition of metallic nanoparticles (NPs) on the electrode surface (ES). These materials have been successfully used to detect an extended range of biomolecules of clinical interest, such as uric acid (UA), dopamine (DA), ascorbic acid (AA), adenine, guanine, and others. The most common method is electrochemical synthesis. In the composites, which are often combined with metallic NPs, the interaction between the graphene derivatives-including graphene oxide (GO), reduced graphene oxide (RGO), or graphene quantum dots (GQDs)-and the CPs is usually governed by non-covalent functionalization through pi-pi interactions, hydrogen bonds, and van der Waals (VW) forces. The functionalization of GO, RGO, or GQDs with CPs has been shown to speed up electron transfer during the oxidation process, thus improving the electrochemical response of the resulting sensor. The oxidation mechanism behind the electrochemical response of the sensor seems to involve a partial charge transfer (CT) from the analytes to graphene derivatives, due to the overlapping of pi orbitals.

The objective of this study consisted of the development of new materials with antimicrobial properties at the nanometric scale that could lead to an increase in therapeutic efficacy and reduction of toxic side effects. This work focuses on obtaining and characterizing stable suspensions with narrow size distribution with antimicrobial properties. The stability of the suspensions obtained by an adapted co-precipitation method was evaluated by ultrasonic measurements. The size and size distribution of the particle populations were determined using scanning electron microscopy (SEM), and dynamic light scattering (DLS). Both methods of analysis showed a narrow distribution of particles. DLS gave a monomodal distribution with hydrodynamic diameters around 38 nm for ciprofloxacin embedded in silver doped hydroxyapatite (AgHA-C) and 45.7 nm for tetracycline embedded in silver doped hydroxyapatite (AgHA-T). The average diameters calculated from SEM were 17 nm for AgHA-C and 19 nm for AgHA-T. Both Ciprofloxacin and Tetracycline influenced the hydroxyapatite structure, which led to the appearance of new vibrational bands characteristic of the specific chemical composition in the FTIR spectrum. The antimicrobial properties of the AgHA-C and AgHA-T suspensions were assessed using the most common reference microbial strains Staphylococcus aureus ATCC 25923, Escherichia coli ATCC 25922, and Candida albicans ATCC 10231. The results of the in vitro antimicrobial assays determined that the AgHA-C and AgHA-T suspensions exhibited exceptional antimicrobial activity. Moreover, the data revealed that the antimicrobial activity increased with the increase of the incubation time.