Publications

This paper reports the synthesis and characterization of Cu2ZnSnS4 (CZTS) absorber films, prepared by a two-step electrodeposition of a ZnS (zinc sulfide) binary and a CZT (copper, zinc and tin) ternary precursors on Mo/Ti/Si substrates. The as-electrodeposited ZnS/CZT and CZT/ZnS stacks were thermally treated in a tubular furnace in sulfur environment at 550 degrees C. The role of the ZnS buffer layer is to provide a zinc and sulfur reservoir, needed to complete the formation of kesterite phase. X-ray diffraction and Raman analyses revealed the formation of the CZTS phase. The surface morphology and chemical composition of the films were studied using a scanning electron microscope. The bandgap values inferred from diffuse reflectance data, are discussed with respect to the stoichiometry which is considerably affected by the order of the stacks. Room-temperature photoluminescence of the CZT/ZnS sample showed a board PL band of 1.51 eV. It was found that the film with a ZnS layer on top is preferred for the formation of a Zn-rich single CZTS phase.

The synthesis and characterization of novel ionic liquid crystals based on pyridinium salts with Br- and PF6- counterions are described in this work. These pyridinium salts were derived from 4-hydroxypyridine, both by N- and O-alkylation. The 3,4,5-tri(alkyloxy)-benzyl mesogenic unit was attached to the nitrogen atom of the pyridinium ring. Alkyl chains with a different number of carbon atoms (6, 8, 10, 12 and 14) were employed in order to show the effect on the stability of mesophase. The POM (polarizing optical microscopy) and XRD (powder X-ray diffraction) studies indicated that bromide salts with shorter chains C-6, C-8 and C-10 do not show mesomorphic properties, while longer chain analogues with C-12 and C-14 exhibit two enantiotropic columnar phases. Surprisingly, the pyridinium salts with the larger size PF6- counterion do not exhibit liquid crystal properties.

A recent theory of band ferromagnetism in 3d metals predicts 're-entrant' ferromagnetism at temperatures far above the boiling point of these metals in normal conditions (Teodorescu, C.M., 2021. Spin asymmetry originating from densities of states: Criterion for ferromagnetism, structures and magnetic properties of 3d metals from crystal field based DOSs. Results in Physics 25, 104,241). Metals, and in particular iron rich alloys, are still solid at such extremal temperatures in the Earth's inner solid core. It follows that this piece of the Earth may become ferromagnetic. This hypothesis is investigated in this work in more details, by using densities of states derived by ab initio density functional theory calculations for hexagonal close-packed iron and applying the basic theory of band ferromagnetism derived in the above Reference. The temperature for 're-entrant' ferromagnetism increases with the pressure, ranging between about 6530 and 6640 K for pressures between 330 and 360 GPa; these temperatures are in the range of most estimates for the temperature of the inner solid core of our planet. The dimension of the ferromagnetic "innermost inner core" (IMIC) derived from the estimated Fe magnetic moment are within the dimensions of a IMIC with different anisotropy in the propagation of seismic waves. For body centered cubic Fe no 're-entrant' ferromagnetism is predicted based on the actual model. It follows that the Earth's inner solid core with hexagonal close-packed structure is the main responsible for the geomagnetic field, and also most probably the reversal of this field proceeds by simple rotation of the magnetization of this core, while keeping a non-vanishing magnetic field during the reversal. This might prevent the Earth's surface bombardment with energetic charged particles during the reversals, with beneficial effects for complex lifeforms and for mankind civilization.

Iron-oxide-doped polyaniline (PANI-IO) thin films were obtained by the polymerization of aniline monomers and iron oxide solutions in direct current glow discharge plasma in the absence of a buffer gas for the first time. The PANI-IO thin films were deposited on optical polished Si wafers in order to study surface morphology and evaluate their in vitro biocompatibility. The characterization of the coatings was accomplished using scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), atomic force microscopy (AFM), metallographic microscopy (MM), and X-ray photoelectron spectroscopy (XPS). In vitro biocompatibility assessments were also conducted on the PANI-IO thin films. It was observed that a uniform distribution of iron oxide particles inside the PANI layers was obtained. The constituent elements of the coatings were uniformly distributed. The Fe-O bonds were associated with magnetite in the XPS studies. The surface morphology of the PANI-IO thin films was assessed by atomic force microscopy (AFM). The AFM topographies revealed that PANI-IO exhibited the morphology of a uniformly distributed and continuous layer. The viability of Caco-2 cells cultured on the Si substrate and PANI-IO coating was not significantly modified compared to control cells. Moreover, after 24 h of incubation, we observed no increase in LDH activity in media in comparison to the control. In addition, our results revealed that the NO levels for the Si substrate and PANI-IO coating were similar to those found in the control sample.

In this study curcumin was immobilized in a silica matrix to overcome its poor aqueous solubility and rapid degradation profile. Two kinds of sol-gel powders based on colloidal silica were synthesized and characterized, one prepared with an ethanolic solution of curcumin and the other using cethyltrimethylammonium bromide (CTAB) to solubilize the dye. The successful integration of curcumin in the matrix as well as the interaction with the components of the composite powders was validated by different analysis methods (DSC, FTIR). The samples morphology was evaluated by SEM. UV-Vis and fluorescence studies showed that curcumin was stable, in its enol configuration in both matrices. The sensitivity to ammonia was proved by exposing the powders to NH3 vapors in a sealed vessel. Color changes were measured with a colorimeter. UV-Vis spectra showed that the enol form of the dye in EtOH/CTAB based SiO2 matrices was energetically stable under NH3 atmosphere, even after being kept a few days at low temperature. A fluorescence quenching of both samples was noticed due to interaction curcumin-ammonia. Both samples have antimicrobial properties, the CTAB containing one being more efficient. The EtOH/CTAB based SiO2 powders may represent a novel signaling and antimicrobial system, useful for food or pharmaceutical applications. [GRAPHICS] .

SnO2 nanoparticles have a great potential in photocatalytic and optoelectronic applications by extending their absorbtion and emission from UV to the visible domain. The effect of annealing at 750 degrees C and 1000 degrees C for 3 h in ambient conditions on structural, optical and electrical properties of F&Zn double doped SnO2 nanoparticles synthesized by continuous wave CO2 laser pyrolysis method were investigated for the first time. X-Ray diffraction studies confirmed the expected crystallite size increasing and also the vanishing of divalent tin phases (SnF2, SnO) upon air annealing. Detailed X ray photoelectron spectroscopy (XPS) analysis confirmed that fluorine disappears completely from SnO2 structure at 1000 degrees C. The annealing also induced a reduction in oxygen vacancies as confirmed by Raman spectroscopy and XPS. Transmission FTIR spectroscopy was used for revealing the existence of Sn-O, O-Sn-O, O-H and H-O-H vibrational modes. The optical band gap energies of all annealed samples are in the visible region, decreasing for those that were initially doped with F, and increasing for the only Zn doped sample. Photoluminescence (PL) measurements showed a broad dominant peak in green visible region, around 530 nm. For the sample with the highest content of Zn, PL spectrum shifted to higher wavelengths, respectively to the orange and red regions. The oxygen vacancies concentrations after annealing are correlated with the electrical conductivity of F, F&Zn, and Zn doped SnO2 samples.

For high-field power applications of high-temperature superconductors, it became obvious in recent years that nano-engineered artificial pinning centers are needed for increasing the critical current and pinning potential. As opposed to the artificial pinning centers obtained by irradiation with various particles, which is a quite expensive approach, we have studied superconducting samples having self-assembled defects, created during the sample fabrication, that act as effective pinning centers. We introduced a simple, straight-forward method of estimating the frequency-dependent critical current density by using frequency-dependent AC susceptibility measurements, in fixed temperatures and DC magnetic fields, from the positions of the maxima in the dependence of the out-of-phase susceptibility on the amplitude of AC excitation magnetic field. The results are compatible with a model that stipulates a logarithmic dependence of the pinning potential on the probing current. A mathematical derivation allowed us to estimate from the experimental data the pinning potentials in various samples, and in various DC magnetic fields. The resulted values indicate large pinning potentials, leading to very small probability of magnetic flux escaping the pinning wells, hence, leading to very high critical currents in high magnetic fields.

Photoelectron spectromicroscopy data cubes with sub-micrometer spatial resolution from a lead zirconate titanate thin film are fitted in each spatial point for several areas investigated, and correlations between the results of the fitting parameters are established, enabling one to suggest that surface band bending manifests also in the case of samples with multiple polarization states. These surface band bendings may be used for preliminary assessment of polarization states by using the contrast in binding energy. However, the individual curve fitting of each spectrum and the analysis of correlations between the derived parameters (binding energies and amplitudes) yields results of deeper significance in deriving the distribution of band bending. This allows in some cases discriminating between the origin of the individual components, assessing charging effects and compensation mechanisms, also enabling one to establish correlations between areas with different polarization. It is found that the major part of the investigated areas consist in regions with outwards polarization and without out-of-plane polarization, with the presence of some isolated metal Pb clusters. On a single area, components attributed to inwards polarization are detected, and their formation occurs at the expense of areas without out-of-plane polarization, mostly for a given proportion of the outwards polarization.

NiO-sensitive materials have been synthesized via the hydrothermal synthesis route and calcined in air at 400 degrees C and, alternatively, at 500 degrees C. Structural, morphological, and spectroscopic investigations were involved. As such, the XRD patterns showed a higher crystallinity degree for the NiO calcined at 500 degrees C. Such an aspect is in line with the XPS data indicating a lower surface hydroxylation relative to NiO calcined at 400 degrees C. An HRTEM microstructural investigation revealed that the two samples differ essentially at the morphological level, having different sizes of the crystalline nanoparticles, different density of the surface defects, and preferential faceting according to the main crystallographic planes. In order to identify their specific gas-sensing mechanism towards CO exposure under the in-field atmosphere, the simultaneous evaluation of the electrical resistance and contact potential difference was carried out. The results allowed the decoupling of the water physisorption from the chemisorption of the ambient oxygen species. Thus, the specific CO interaction mechanism induced by the calcination temperature of NiO has been highlighted.

Dextran coated cerium doped hydroxyapatite (Ca(10-x)Cex(PO4)(6)(OH)(2)), with x = 0.05 (5CeHAp-D) and x = 0.1 (10CeHAp-D) were deposited on Si substrates by radio frequency magnetron sputtering technique for the first time. The morphology, composition, and structure of the resulting coatings were examined by scanning electron microscopy (SEM), energy-dispersive x-ray spectroscopy (EDX), atomic force microscopy (AFM), metallographic microscopy (MM), Fourier transform infrared spectroscopy (FTIR), and glow discharge optical emission spectroscopy (GDOES), respectively. The obtained information on the surface morphologies, composition and structure was discussed. The surface morphologies of the CeHAp-D composite thin films are smooth with no granular structures. The constituent elements of the CeHAp-D target were identified. The results of the FTIR measurements highlighted the presence of peaks related to the presence of nu(1), nu(3), and nu(4) vibration modes of (PO43-) groups from the hydroxyapatite (HAp) structure, together with those specific to the dextran structure. The biocompatibility assessment of 5CeHAp-D and 10CeHAp-D composite coatings was also discussed. The human cells maintained their specific elongated morphology after 24 h of incubation, which confirmed that the behavior of gingival fibroblasts and their proliferative capacity were not disturbed in the presence of 5CeHAp-D and 10CeHAp-D composite coatings. The 5CeHAp-D and 10CeHAp-D coatings' surfaces were harmless to the human gingival fibroblasts, proving good biocompatibility.