Eng. Vasilica TOMA

The present study investigates the influence of strontium (Sr) content on the intrinsic properties of barium strontium titanate (Ba1-xSrxTiO3, BST) which was successfully prepared by the conventional solid-state reaction with different concentrations of strontium (x = 0, 0.3, 0.5, 0.6, 0.7, 1). The resulting samples were characterized by X-ray diffraction, scanning electron microscopy, Raman spectroscopy and diffuse reflectance spectroscopy, the dielectric properties being also investigated. Structural and vibrational analyses reveal a structural phase transition from tetragonal to cubic at x = 0.4, with a linear decline of the tetragonality ratio as well as a shrinkage in the unit cell volume that occur with increasing Sr content. The morphological study shows that the grain size decreases as the Sr content increases in the tetragonal phase. Yet, upon the phase transition from tetragonal to cubic, the grain size initially increases, followed by a subsequent decrease with further Sr addition. It has been found that the band gap shows a decrease as Sr content increases. The temperature dependence of the dielectric parameters reveals that the Curie temperature as well as the dielectric constant and the loss tangent are strongly affected by the addition of Sr. The activation energy derived from the dielectric response, was found to be in the range 0.685-1.065eV, suggesting the dominance of doubly ionized oxygen vacancy for conduction and relaxation mechanism. Ab initio calculations were done employing the Linear Combination of Atomic Orbitals (LCAO) method. The bandgap energy (Eg) and the structural parameters were calculated using various types of exchange-correlation functionals (PWGGA, PBE, B3LYP and PBE0). A good agreement with the experimental results is achieved using the PBE0 functional. This study contributes to a better understanding of the structure-property relationship in BaSrTiO3 and provides valuable insights for optimizing its performance in various technological applications.

The present study investigates the influence of strontium (Sr) content on the intrinsic properties of barium strontium titanate (Ba1-xSrxTiO3, BST) which was successfully prepared by the conventional solid-state reaction with different concentrations of strontium (x = 0, 0.3, 0.5, 0.6, 0.7, 1). The resulting samples were characterized by X-ray diffraction, scanning electron microscopy, Raman spectroscopy and diffuse reflectance spectroscopy, the dielectric properties being also investigated. Structural and vibrational analyses reveal a structural phase transition from tetragonal to cubic at x = 0.4, with a linear decline of the tetragonality ratio as well as a shrinkage in the unit cell volume that occur with increasing Sr content. The morphological study shows that the grain size decreases as the Sr content increases in the tetragonal phase. Yet, upon the phase transition from tetragonal to cubic, the grain size initially increases, followed by a subsequent decrease with further Sr addition. It has been found that the band gap shows a decrease as Sr content increases. The temperature dependence of the dielectric parameters reveals that the Curie temperature as well as the dielectric constant and the loss tangent are strongly affected by the addition of Sr. The activation energy derived from the dielectric response, was found to be in the range 0.685-1.065eV, suggesting the dominance of doubly ionized oxygen vacancy for conduction and relaxation mechanism. Ab initio calculations were done employing the Linear Combination of Atomic Orbitals (LCAO) method. The bandgap energy (Eg) and the structural parameters were calculated using various types of exchange-correlation functionals (PWGGA, PBE, B3LYP and PBE0). A good agreement with the experimental results is achieved using the PBE0 functional. This study contributes to a better understanding of the structure-property relationship in BaSrTiO3 and provides valuable insights for optimizing its performance in various technological applications.

The technology of perovskite solar cells (PSC) is getting close to breaching the consumer market. Yet, one of the current challenges is to reduce the toxicity during their fabrication by reducing the use of the toxic solvents involved in the perovskite fabrication process. A good solubilization of lead halides used in hybrid perovskite preparation is required, and it is only possible with polar solvents. A mixture of dimethylformamide (DMF) and dimethyl sulfoxide (DMSO) is the most popular solvent combination for a perovskite precursor solution. DMF is necessary to ensure a good dissolution of lead iodide, but it is also the most toxic solvent. In this paper, we study the replacement of the dimethylformamide with presumably less toxic alternatives, such as N-methyl-2-Pyrrolidone (NMP) and ethyl acetate (EA), for the preparation of the K(0.1)FA(0.7)MA(0.2)PbI(2.8)Cl(0.2) (KFAMA) hybrid perovskite. The perovskite thin films were investigated by various characterization techniques: X-ray diffraction, atomic force microscopy, scanning electron microscopy, and UV-vis spectroscopy, while the photovoltaic parameters were determined by measuring the IV curves of the corresponding solar cells. The present study shows that by keeping the same deposition parameters as when only DMF solvent is used, the partial solvent substitution with NMP and EA gives promising results for reducing the toxicity of the fabrication process of KFAMA-based PSCs. Thus, with no specific optimization of the deposition process, and for the maximum possible partial substitution of DMF with NMP and EA solvents, the loss in the power conversion efficiency (PCE) value is only 35% and 18%, respectively, associated with the more structural defects promoted by NMP and EA.

Organic-inorganic hybrid perovskite solar cells are within the emerging photovoltaic technologies. The combination of different halogen ions, in certain fill fractions, is one of the methods to improve the perovskite film properties. Herein, fabrication and characterization of perovskite cells in standard mesoscopic architecture using one-step deposition method has been done. The role of the halogen ions (Chlorine or Bromine) on crystal structure growth and photoelectric performance has been investigated. X-ray diffraction, scanning electron microscopy, atomic force microscopy and optical microscopy analysis were performed. The microstructure, composition and morphology of CH3NH3PbI1.8Br1.2 and CH3NH3PbI1.8Cl1.2 films are dissimilar, although identical fabrication method was used. Same holds for optical properties, band gap energies of 1.84 eV and 1.63 eV, respectively, being obtained. Integrated in solar cells, the maximum power conversion efficiency of the Br based devices is beyond 10%, while for those based on Cl, the efficiency drops around 5%.

Piezoelectric hard/soft effects of multivalence co-dopants (Sb and Mn) in correlation with their location in the lattice, were investigated in PZT ceramics, prepared by conventional ceramic technology, with the following compositions: Pb0.98Sr0.02 ((Ti0.49Zr0.51)(1-0.015-x)Mn0.015Sbx)O-3 with x = 0, 0.005, 0.01, 0.02, 0.03, where antimony was initially assumed to substitute for Ti/Zr ions. The antimony valence state was found to be +3 in all samples by X-ray Photoelectron Spectroscopy investigations. The Electron Paramagnetic Resonance spectra evidenced a steep enhancement of the Mn2+ concentration upon increasing antimony doping level, explained by a charge compensation mechanism, between the Sb3+ ions substituting Pb2+ at the A-sites and the Mn2+ ions, localized at the B-sites. The incorporation of Sb3+ at the A-site of the PZT lattice is also supported by the variation of the lattice parameters, determined by X-ray Diffraction, with the increasing Sb concentration. The investigation of the dielectric, electromechanical and ferroelectric properties evidenced a hard piezoelectric behavior, mainly attributed to the presence of large sized Mn2+ ions, localized at B-sites. Our results prove that the piezoelectric hard/soft response is decisively influenced by the interplay between multiple valence states and locations of the co-dopants, on one hand, and the charge compensation mechanisms, on the other hand. This provides indirect information about the location of some co-dopants which can substitute for both cationic sites in the PZT based ceramics.

Composites of BaTiO3 (BT) and doped-PZT (d-PZT) micro-particles randomly dispersed in a PDMS matrix were prepared by a molding process. The morpho-structural characterization, performed by SEM and XRD, showed ceramic micro-grains of cubic BT and orthorhombic d-PZT, randomly dispersed in the PDMS matrix. Polarization (P) as a function of the applied field (E) was measured for composite samples, as well as for polymer samples. Hysteresis loops typical for a dielectric material were obtained, but also atypical ones, especially for higher fraction of polymer in composite, lower fields and shorter measuring periods, as a result of the dielectric relaxation in polymer and the presence of interfacial polarization charges at the contact between polymer and ferroelectric. All these composites show very low polarizations (less than 0.2 mu C/cm(2) and 0.05 mu C/cm(2) the maximum and remnant polarization, respectively), caused by the very low dielectric constant of the polymer (less than 10), which drastically reduces, up to 100 times, the electric field effectively applied to the ferroelectric. Weak pyroelectric response was recorded on BT/PDMS, but a typical behavior of a pyroelectric detector was observed. A figure of merit of the material which exceeds 10(-4) m(2) /C was estimated.

Hybrid perovskites based solar cells have demonstrated high conversion efficiency but poor long-term stability. This study reports on the results obtained after doping the CH3NH3PbI2.6Cl0.4 mixed halide perovskite with imidazolium (C3N2H5+, denoted IM) on the "A site" position of a perovskite, to improve photovoltaic performances and stability of hybrid perovskite solar cells. The perovskite films were investigated exhaustively by different characterization techniques: X-ray diffraction, Atomic Force Microscopy, Scanning Electron Microscopy, UV-Vis, X-ray Photoelectron Electron Paramagnetic Resonance spectroscopies, Impedance Spectroscopy and Incident Photon-to-Electron Conversion Efficiency. The photovoltaic parameters were determined by measuring the IV curves of the corresponding solar cells. The amount of IM inserted in the perovskite play a key role on the film properties. The calculated new tolerance factors according to the "globularity factor" are experimentally proved and thus at doping concentrations greater than 20% for CH3NH3PbI2.6Cl0.4 perovskite the 3D structure is no longer obtained. However, below this value, the IM substituted perovskite film possesses an improved film quality and crystallinity as compared to the pristine film. Substituting MA+ with IM+ provides a favorable way to reduce recombination processes and shows great potential to achieve high stability, and an improved charge generation, resulting in increased PCE values. We find that the optimal percentage of imidazolium incorporation to achieve better stability of solar cells is 6%.