National Institute Of Materials Physics - Romania

Currently, the treatment of wounds is still a challenge for healthcare professionals due to high complication incidences and social impacts, and the development of biocompatible and efficient medicines remains a goal. In this regard, mesoporous materials loaded with bioactive compounds from natural extracts have a high potential for wound treatment due to their nontoxicity, high loading capacity and slow drug release. MCM-41-type mesoporous material was synthesized by using sodium trisilicate as a silica source at room temperature and normal pressure. The synthesized mesoporous silica was characterized by using Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), N2 absorption-desorption (BET), Dynamic Light Scattering (DLS) and Fourier transform infrared spectroscopy (FT-IR), revealing a high surface area (BET, 1244 m2/g); pore diameter of approx. 2 nm; and a homogenous, ordered and hexagonal geometry (TEM images). Qualitative monitoring of the desorption degree of the Salvia officinalis (SO) extract, rich in ursolic acid and oleanolic acid, and Calendula officinalis (CO) extract, rich in polyphenols and flavones, was performed via the continuous recording of the UV-VIS spectra at predetermined intervals. The active ingredients in the new composite MCM-41/sage and marigold (MCM-41/SO & CO) were quantified by using HPLC-DAD and LC-MS-MS techniques. The evaluation of the biological composites' activity on the wound site was performed on two cell lines, HS27 and HaCaT, naturally involved in tissue-regeneration processes. The experimental results revealed the ability to stimulate collagen biosynthesis, the enzymatic activity of the main metalloproteinases (MMP-2 and MMP-9) involved in tissue remodeling processes and the migration rate in the wound site, thus providing insights into the re-epithelializing properties of mesoporous composites.

A convenient and low-cost sol-gel approach for the one-step synthesis of ZnO-P2O5-rGO nanostructures with tuned bandgap and fluorescence was investigated. The obtained hybrid nanostructures exploit the properties of zinc oxide, graphene oxide and phosphorous oxide as promising candidates for a wide range of optoelectronic applications. A predominant amorphous structure, ZnO-P2O5-rGO, containing ZnO nanorods was evidenced by X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM). The estimated size of the ZnO nanorods in nanostructures with P2O5 was noticed to decrease when the P2O5/ZnO ratio was increased. The presence of ZnO, P2O5 and rGO was confirmed by Fourier-transform infrared spectroscopy (FTIR) and Raman investigation. P2O5 was noticed to tune the bandgap and the fluorescence emissions of the nanostructured films, as estimated by UV-Vis-NIR and fluorescence spectroscopy, respectively. The electrical measurements performed at room temperature showed that the main influence on the film's resistivity does not come from the 1% rGO doping but from the P2O5/ZnO ratio. It was found that a 10/90 molar ratio of P2O5/ZnO decreases the resistivity almost seven-fold compared with rGO-doped ZnO films.

The current study reports on the fabrication of composite scaffolds based on polycaprolactone (PCL) and cerium (Ce)-containing powders, followed by their characterization from compositional, structural, morphological, optical and biological points of view. First, CeO2, Ce-doped calcium phosphates and Ce-substituted bioglass were synthesized by wet-chemistry methods (precipitation/coprecipitation and sol-gel) and subsequently loaded on PCL fibres processed by electrospinning. The powders were proven to be nanometric or micrometric, while the investigation of their phase composition showed that Ce was present as a dopant within the crystal lattice of the obtained calcium phosphates or as crystalline domains inside the glassy matrix. The best bioactivity was attained in the case of Ce-containing bioglass, while the most pronounced antibacterial effect was visible for Ce-doped calcium phosphates calcined at a lower temperature. The scaffolds were composed of either dimensionally homogeneous fibres or mixtures of fibres with a wide size distribution and beads of different shapes. In most cases, the increase in polymer concentration in the precursor solution ensured the achievement of more ordered fibre mats. The immersion in SBF for 28 days triggered an incipient degradation of PCL, evidenced mostly through cracks and gaps. In terms of biological properties, the composite scaffolds displayed a very good biocompatibility when tested with human osteoblast cells, with a superior response for the samples consisting of the polymer and Ce-doped calcium phosphates.

This work evaluates the effects of manganese (Mn) doping on the morpho-structural features, mechanical performance, and in vitro biological response of beta-tricalcium phosphate (beta-TCP) derived bioceramics for bone tissue engineering applications. Five different Mn doping levels (i.e., 0.01%, 0.05%, 0.1%, 0.5%, and 1 wt.%) were investigated, with the beta-TCP-based bioceramics being sintered at four temperatures (i.e., 1000, 1100, 1200, and 1300 degrees C). A densification improvement was induced when using Mn in excess of 0.05 wt.%; the densification remained stationary in the sintering temperature range of 1200 - 1300 degrees C. The structural analyses evidenced that all samples sintered at 1000 and 1100 degrees C were composed of beta-TCP as major phase and hydroxyapatite (HA) as a minor constituent (similar to 4-6 wt.%). At the higher temperatures (1200 and 1300 degrees C), the formation of alpha-TCP was signalled at the expense of both beta-TCP and HA. The Mn doping was evidenced by lattice parameters changes. The evolution of the phase weights is linked to a complex inter-play between the capacity of the compounds to incorporate Mn and the thermal decomposition kinetics. The Mn doping induced a reduction in the mechanical performance (in terms of compressive strength, Vickers hardness and elastic modulus) of the beta-TCP-based ceramics. The metabolic activity and viability of osteoblastic cells (MC3T3-E1) for the ceramics were studied in both powder and compacted pellet form. Ceramics with Mn doping levels lower than 0.1 wt.% yielded a more favorable microenvironment for the osteoblast cells with respect to the undoped beta-TCP. No cytotoxic effects were recorded up to 21 days. The Mn-doped beta-TCPs showed a significant increase (p < 0.01) in alkaline phosphatase activity with respect to pure beta-TCP.

A testing methodology and a new "anchor"geometry for tensile samples were developed for evaluation of the W/Cu joint strength between the W monoblock and the CuCrZr cooling pipe joined via the Cu interlayer in the ITER-specification monoblock. The proposed samples can be machined from the ITER-specification monoblock. These monoblock tensile samples are designed for uniaxial tests allowing their remote manipulation for testing in hot cells after neutron irradiation, which is crucial for the assessment of the effect of this irradiation. For validation purposes, tensile tests with standard miniaturised dog-bone samples were performed using prototype block-to-block joints (W/CuCrZr) produced with the field-assisted sintering technique. The results are obtained from the conventional and the new tensile samples. Conventional samples were machined from the W/CuCrZr block-to-block joints, while the new "anchor"tensile samples were machined from the W/CuCrZr block-toblock joints and ITER monoblock containing the W block and Cu interlayer. A good agreement in the evaluation of the joint strength was obtained. The fracture surfaces and the joint interface were investigated with scanning electron microscopy. Micro-hardness was characterised across the joint interface.

We report a novel approach in producing and characterizing enriched isotopic selenium-82 (82Se) thin films with trigonal hexagonal crystal structure (t-82Se), the most thermodynamically stable form of the element. The ob-tained t-82Se thin films are used as targets in accelerator based nuclear structure experiments. Several 82Se thin films with thicknesses around 5 mg/cm2 (10.4 & mu;m) were deposited on 5 mg/cm2 (3 & mu;m) tantalum (Ta) foils by vacuum evaporation-condensation method. The condensed 82Se films exhibit unstable amorphous structure (a-82Se), therefore were converted to t-82Se by means of an appropriate vacuum heat treatment developed in the target laboratory of IFIN-HH. After the thermal treatment, the microstructure, morphology and composition of the 82Se films were evaluated before and after the vacuum thermal treatment using Fourier Transform Raman Spectroscopy (FT-Raman), X-Ray Diffraction (XRD), Atomic Force Microscopy (AFM), Scanning Electron Mi-croscopy (SEM) and Energy-Dispersive X-Ray Spectroscopy (EDX) techniques. Furthermore, an in-beam & gamma;-spectroscopy experiment performed at the 9-MV tandem accelerator of IFIN-HH confirmed that the ther-mally treated t-82Se films possess high durability and high purity with no detectable contamination and no mass loss.

Motivated by the goal of developing ultralow power, smart and multifunctional nano (micro) electronic devices, research has shown unwavering interest in synthesis methods, architectures and interphase connectivity of composites containing magnetostrictive and piezoelectric phases, known as magnetoelectric (ME) materials. Herein we report on CoFe2O4/0.92Bi0.5Na0.5TiO3-0.08BaTiO3 biphasic ME composites, obtained by sol-gel chemistry, by mixing the precursor sols of the two phases into one precursor sol and further transforming it into gel, with the goal of obtaining homogeneous nanocomposites with magnetoelectric properties. The structural properties, the temperature dependance of dielectric properties, the magnetic and magnetoelectric properties of these biphasic mixtures, with various molar ratios CoFe2O4/ BNT-BT0.08 = 0.5:1, 1:1 and 1.5:1, are investigated. It is observed that the amount of CoFe2O4 and the synthesis in situ of these composites influences their macroscopic properties showing a high difficulty of carrying out an efficient poling resulting in small piezoelectric and magnetoelectric response. It was concluded that the synthesis procedure, the type of architecture and the interphase connectivity are of outmost importance for magnetoelectric properties based on lead-free materials. (c) 2023 Published by Elsevier B.V.

Probing of the free surface ferroelectric properties of thin polar films can be achieved either by estimating the band bending variance under the top-most layer or by studying the extent of the extrinsic charge accumulated outside the surface. Photoemitted or incoming low-energy electrons can be used to characterize locally both properties in a spectromicroscopic approach. Thin ferroelectric lead zirco-titanate (PZT) is investigated by combining low energy/mirror electron microscopy (LEEM/MEM) with photoemission electron microscopy (PEEM) and high-resolution photoelectron spectroscopy (XPS). Significant extrinsic negative compensation charge is proven to accumulate on the surface of the outward polarized thin film, indicated by high MEM-LEEM transition values, up to 15.3 eV, and is correlated with the surface electrostatic potential, which can be partially screened either by electrons interacting with the sample or by soft X-rays through the ejection of secondary electrons and generation of positive charge under the surface. A radiation-induced surface charge compensation effect is observed. The study indicates that air-exposed high quality ferroelectric thin films show large negative surface potentials, determined locally on the surface, which are nevertheless sensitive to beam damage and molecular desorption. These values represent a confirmation of previously estimated surface potential energy values determined from the LEED data on clean surfaces.

Properties of surface species of the nematic mixture E7 in contact with inorganic oxides (especially those containing more or less aluminium ions) are in detail investigated by infrared spectroscopy and thermogravimetry. The absorption infrared peaks were decomposed into Gaussian components, the procedure allowing an easier comparison with the behaviour of related composites. We worked at enough small concentrations of the E7 relatively to support this ratio permitting the (partial) elimination of the species belonging to the bulk. Species put here in evidence are species that are hydrogen bonded to the surface of OH groups, molecules randomly oriented on the surface, some species bonded by involvement of pi electrons of the CN group to the aluminium ions, thus implying a strong interaction to the support. Supramolecular assemblies of E7 molecules are thus followed up.