National Institute Of Materials Physics - Romania

Mononuclear Mn(II) coordination compound, [Mn(H2L)Cl-2] (1), was synthesized by the reaction of H2L and MnCl2 center dot 4H(2)O in methanol where H2L is tridentate ONO-donor hydrazone ligand [H2L = (E)-N'-(2-hydroxy-5-iodobenzylidene)isonicotinohydrazide]. The reaction of H2L with MnCl2 center dot 4H(2)O in the presence of excess amount of NaN3 in methanol gave an azido bridged dinuclear Mn(III) coordination compound, [Mn-2(L)(mu-N-3)(2)(CH3OH)(2)] (2), whereas in the presence of low amount of NaN3, a phenolate bridged dinuclear Mn(II) coordination compound, [Mn-2(HL)(2)(CH3OH)(2)Cl-2]center dot CH3OH (3), was obtained. These compounds were characterized by elemental analysis, spectroscopic methods, single crystal X-ray analysis and magnetic measurements. The structural studies indicated that the ligand is coordinated as ONO-donor ligand in 1-3 and behave as a neutral, dianionic and monoanionic ligand in compounds 1, 2 and 3, respectively. There is a good agreement between spectroscopic properties and structures of the compounds. Several synthetic attempts indicated that the azide anion has considerable effect on the formation of phenolate bridged dinuclear Mn(II) coordination compound which attributed to its general basic properties. Magnetic measurements indicate the formation of dinuclear molecules with ferromagnetic intramolecular couplings in the case of 2 and 3 as well as with much weaker and distributed antiferromagnetic interactions among the dinuclear units of these compounds. (C) 2020 Elsevier Ltd. All rights reserved.

In this work, (Ba0.75Sr0.25) (Ti0.95Co0.05) O-3 perovskite nanostructured material, denoted subsequently as Co-doped BaSrTiO3, was synthesized in a one-step process in hydrothermal conditions. The obtained powder was heat-treated at 800 degrees C and 1000 degrees C, respectively, in order to study nanostructured powder behavior during thermal treatment. The Co-doped BaSrTiO3 powder was pressed into pellets of 5.08 cm (2 inches) then used for thin film deposition onto commercial Al2O3 substrates by RF sputtering method. The microstructural, thermal, and gas sensing properties were investigated. The electrical and thermodynamic characterization allowed the evaluation of thermodynamic stability and the correlation of structural features with the sensing properties revealed under real operating conditions. The sensing behavior with respect to the temperature range between 23 and 400 degrees C, for a fixed CO2 concentration of 3000 ppm, highlighted specific differences between Co-doped BaSrTiO3 treated at 800 degrees C compared to that treated at 1000 degrees C. The influence of the relative humidity level on the CO2 concentrations and the other potential interfering gases was also analyzed. Two possible mechanisms for CO2 interaction were then proposed. The simple and low-cost technology, together with the high sensitivity when operating at room temperature corresponding to low power consumption, suggests that Co-doped BaSrTiO3 has a good potential for use in developing portable CO2 detectors.

Silica-based bioactive glasses (SBG) hold great promise as bio-functional coatings of metallic endo-osseous implants, due to their osteoproductive potential, and, in the case of designed formulations, suitable mechanical properties and antibacterial efficacy. In the framework of this study, the FastOs(R)BG alkali-free SBG system (mol%: SiO2-38.49, CaO-36.07, P2O5-5.61, MgO-19.24, CaF2-0.59), with CuO (2 mol%) and Ga2O3 (3 mol%) antimicrobial agents, partially substituting in the parent system CaO and MgO, respectively, was used as source material for the fabrication of intentionally silica-enriched implant-type thin coatings (similar to 600 nm) onto titanium (Ti) substrates by radio-frequency magnetron sputtering. The physico-chemical and mechanical characteristics, as well as the in vitro preliminary cytocompatibility and antibacterial performance of an alkali-free silica-rich bio-active glass coating designs was further explored. The films were smooth (R-RMS < 1 nm) and hydrophilic (water contact angle of similar to 65 degrees). The SBG coatings deposited from alkali-free copper-gallium co-doped FastOs(R)BG-derived exhibited improved wear performance, with the coatings eliciting a bonding strength value of similar to 53 MPa, Lc3 critical load value of similar to 4.9 N, hardness of similar to 6.1 GPa and an elastic modulus of similar to 127 GPa. The Cu and Ga co-doped SBG layers had excellent cytocompatibility, while reducing after 24 h the Staphylococcus aureus bacterial development with 4 orders of magnitude with respect to the control situations (i.e., nutritive broth and Ti substrate). Thereby, such SBG constructs could pave the road towards high-performance bio-functional coatings with excellent mechanical properties and enhanced biological features (e.g., by coupling cytocompatibility with antimicrobial properties), which are in great demand nowadays.

Core-double shell nylon-ZnO/polypyrrole electrospun nanofibers were fabricated by combining three straightforward methods (electrospinning, sol-gel synthesis and electrodeposition). The hybrid fibrous organic-inorganic nanocomposite was obtained starting from freestanding nylon 6/6 nanofibers obtained through electrospinning. Nylon meshes were functionalized with a very thin, continuous ZnO film by a sol-gel process and thermally treated in order to increase its crystallinity. Further, the ZnO coated networks were used as a working electrode for the electrochemical deposition of a very thin, homogenous polypyrrole layer. X-ray diffraction measurements were employed for characterizing the ZnO structures while spectroscopic techniques such as FTIR and Raman were employed for describing the polypyrrole layer. An elemental analysis was performed through X-ray microanalysis, confirming the expected double shell structure. A detailed micromorphological characterization through FESEM and TEM assays evidenced the deposition of both organic and inorganic layers. Highly transparent, flexible due to the presence of the polymer core and embedding a semiconducting heterojunction, such materials can be easily tailored and integrated in functional platforms with a wide range of applications.

Almost six decades ago, in Romania a small group of physicists begun to study chalcogenide compositions, motivated primarily by the desire to understand the phase-change phenomenon in these materials, discovered recently, at that time, by Stanford R. Ovshinsky. It took not too long for them to realize the challenges these materials set to the research. With newcomers to the field, the research was broadened. In some cases just for basic research, to model, and to understand the chalcogenide materials, whereas in other cases, the applicative potential was revealed and used. Herein, the evolution of the field of these somewhat exotic materials is followed, listing the main contributions done in Romania, both in basic and applied research.

Pd deposited on CeOx-MnOx/La-Al2O3 has been prepared as a sensitive material for methane (CH4) detection. The effect of different amounts (1.25%, 2.5% and 5%) of Pd loading has been investigated. The as prepared materials were deposited on Pt microcoils using a drop-coating method, as a way of developing pellistors operated using a Wheatstone bridge configuration. By spanning the operating temperature range between 300 degrees C and 550 degrees C, we established the linearity region as well as the maximum sensitivity towards 4900 ppm of CH4. By making use of the sigmoid dependence of the output voltage signal from the Wheatstone bridge, the gas surface reaction and diffusion phenomena have been decoupled. The pellistor with 5% Pd deposited on CeOx-MnOx/La-Al2O3 exhibited the highest selective-sensitivity in the benefit of CH4 detection against threshold limits of carbon monoxide (CO), sulfur dioxide (SO2) and hydrogen sulfide (H2S). Accordingly, adjusting the percent of Pd makes the preparation strategies of pellistors good candidates towards CH4 detection.

Post-implant infections are a major health problem, and it is well-known that treating them with conventional drugs is accompanied by many disadvantages. The development of new biomaterials with enhanced antimicrobial properties are of major interest for the scientific world. The aim of this study was to synthesize and characterize hydroxyapatite doped with Samarium (Ca10-xSmx(PO4)(6)(OH)(2), x(Sm) = 0.05, 5Sm-HAp) suspensions, pellets and coatings. The 5Sm-HAp coatings on Si substrates were obtained by rf magnetron sputtering technique. The different techniques such as ultrasound measurements, scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), Glow Discharge Optical Emission Spectroscopy (GDOES), X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) were used to examine the obtained coatings. The results showed that the doped Sm ions entered the structure of hydroxyapatite successfully and Sm ions was uniformly doped onto the surface of the support. The depth profile curves of Ca, P, O, H, Ce and Si elements exhibit their presence from a surface to substrate interface as function of sputtering time. XPS analysis indicated as calcium-phosphate structures enriched in Sm3+ ions. Furthermore, the antimicrobial properties of the 5Sm-HAp suspensions, targets and coatings were assessed against Escherichia coli ATCC 25922, Staphylococcus aureus ATCC 25923 and Candida albicans ATCC 10231. The results of the antimicrobial assays highlighted that that the samples presented a strong antimicrobial activity against the tested microbial strains. The results showed that the coatings after 48 h of incubation inhibited the growth of all tested microbial strains under the value of 0.6 Log CFU/mL. This study shows that the 5Sm-HAp samples are good candidates for the development of new antimicrobial agents.

The influence of Ag and Au nanoparticles and reduced graphene oxide (RGO) sheets on the photodegradation of alpha-lipoic acid (ALA) was determined by UV-VIS spectroscopy. The ALA photodegradation was explained by considering the affinity of thiol groups for the metallic nanoparticles synthesized in the presence of trisodium citrate. The presence of excipients did not induce further changes when ALA interacts with Ag and Au nanoparticles with sizes of 5 and 10 nm by exposure to UV light. Compared to the Raman spectrum of ALA powder, changes in Raman lines' position and relative intensities when ALA has interacted with films obtained from Au nanoparticles with sizes between 5 and 50 nm were significant. These changes were explained by considering the chemical mechanism of surface-enhanced Raman scattering (SERS) spectroscopy. The photodegradation of ALA that had interacted with metallic nanoparticles was inhibited in the presence of RGO sheets.

One of the key elements in assessing traffic safety on the roads is the detection of asphalt conditions. In this paper, we propose an optical sensor based on GeSi nanocrystals embedded in SiO2 matrix that discriminates between different slippery road conditions (wet and icy asphalt and asphalt covered with dirty ice) in respect to dry asphalt. The sensor is fabricated by magnetron sputtering deposition followed by rapid thermal annealing. The photodetector has spectral sensitivity in the 360-1350 nm range and the signal-noise ratio is 10(2)-10(3). The working principle of sensor setup for detection of road conditions is based on the photoresponse (photocurrent) of the sensor under illumination with the light reflected from the asphalt having different reflection coefficients for dry, wet, icy and dirty ice coatings. For this, the asphalt is illuminated sequentially with 980 and 1064 nm laser diodes. A database of these photocurrents is obtained for the different road conditions. We show that the use of both k-nearest neighbor and artificial neural networks classification algorithms enables a more accurate recognition of the class corresponding to a specific road state than in the case of using only one algorithm. This is achieved by comparing the new output sensor data with previously classified data for each algorithm and then by performing an intersection of the algorithms' results.