Publications

A simple dynamic method was developed to evaluate the components in the equivalent circuit of a ferroelectric capacitor. The method is based on the application of short trapezoidal voltage pulses of variable amplitude and the analysis of the resulting current by considering the ferroelectric capacitor as a parallel R-p-C-p equivalent circuit. The values of R-p and C-p components are obtained in relation to different stages of polarization switching as the amplitude of the applied pulses increases. The most important result obtained by applying the present method is the evidence of an abrupt decrease of the R-p value (about 2 orders of magnitude) at the coercive voltage, while the equivalent C-p does not present a dramatic variation during polarization switching. This is interpreted in the context of negative capacitance obtained for ferroelectrics when polarization passes through zero value. The results obtained by using the proposed dynamic characterization method that will be referred to as "dynamic dielectric characterization", are in good agreement with those obtained by classic capacitance-voltage measurements. A method to stabilize the negative capacitance for longer periods of time is also presented by adding an external resistance in series with the ferroelectric capacitor.

The thermal behavior of Cu-doped TiO2 gels obtained by the sol-gel method was investigated by thermogravimetric and differential thermal analysis (TG/DTG/DTA) and differential scanning calorimetry (DSC) measurements. The comparative investigation of the structure and morphology of the as-prepared gels and of the nanopowders obtained by annealing them was realized by transmission electron microscopy (TEM), Fourier transmission infrared spectroscopy (FTIR), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Significant differences were noticed depending on the amount of dopant (0.5 or 2.0 mol % CuO). A higher dopant concentration resulted in a more complex decomposition of the sample. This behavior was associated with the formation of various molecular species in the sol-gel solutions before gelation, determined by the different amount of the dopant used.

Phase-change memories have reached an advanced degree of maturity, although, to be able to meet the increasing storage demand, multilevel capability is needed. A GeTe memristor is obtained in an amorphous state and it is subjected to a specific thermal treatment which initiates the transition toward the crystalline state. It is found that this crystalline state initialization process is highly beneficial for subsequently obtaining a large number of intermediate resistive states between the high and low resistive states. Multiple resistance levels are achieved by operating the devices in both DC sweeps and rectangular pulse modes in the low-voltage subthreshold regime. The conduction is modeled using a space charge limited conduction model, showing three distinct conduction regions in the high resistive state which merge toward a single conduction region as the low resistive state is approached. The obtained memristors can be used as multilevel nonvolatile memories or as synapses in neuromorphic computing.

We explore higher order dynamical effects in the transport through a two-dimensional nanoscale electron system embedded in a three-dimensional far-infrared photon cavity. The nanoscale system is considered to be a short quantum wire with a single circular quantum dot defined in a GaAs heterostructure. The whole system, the external leads and the central system are placed in a constant perpendicular magnetic field. The Coulomb interaction of the electrons, the paraand diamagnetic electron-photon interactions are all treated by a numerically exact diagonalization using step-wise truncations of the appropriate many-body Fock spaces. We focus on the difference in transport properties between a description within an electric dipole approximation and a description including all higher order terms in a single photon mode model. We find small effects mostly caused by an electrical quadrupole and a magnetic dipole terms that depend strongly on the polarization of the cavity field with respect to the transport direction and the photon energy. When the polarization is aligned along the transport direction we find indications of a weak self-induction that we analyze and compare to the classical counterpart, and the self-energy contribution of high-order interaction terms to the states the electrons cascade through on their way through the system. Like expected the electron-photon interaction is well described in the dipole approximation when it is augmented by the lowest order diamagnetic part for a nanoscale system in a cavity in an external magnetic field.

A simple view of ferroelectricity is proposed for a thin film with uniform polarization oriented perpendicular to its surface, starting from the assumption that this situation is always accompanied by charge accumulation in the outer metal electrodes, in the contamination layers or near the surface, in the ferroelectric film itself. Starting with the formula derived for an "elemental" dipole moment in the film, simple statistical mechanics allows one to derive hysteresis cycles, and their dependence on temperature starting with only two parameters: the dielectric constant of the material and the maximum value of the dipole moment of a unit cell. Values obtained for Curie temperatures and coercive fields agree well with experiments. "Exact" energy dependencies on the asymmetry parameter are derived, and their connection with the Landau-Ginsburg-Devonshire is proven. By considering also the dipolar interaction in a continuous model, in addition to the ordering energy in the presence of surface charge accumulation, one may estimate the distribution of the polarization inside the film and the validity of the hypothesis of uniform polarization.

For successful bone remodelling, the implantable 3D structures require suitable internal architectures which can be achieved by the use of fibres as natural templates. The ability of fibres to generate complex configurations for 3D bioceramic products was preliminary reported by sacrificial fibrous-porogen method. This study aims to demonstrate the safe-prospect of repurposing natural-fibres (i.e. luffa, hemp, wool) for embedment into a calcium phosphate (CaPs) matrix prepared through a completely reproducible route, and the beneficial influence of fibres upon structural, topographic and mechanical features of CaPs-products, since a complete assessment of the fibres-combustion-products resulted after thermal treatment was not yet disclosed. The complex investigation program based on i) thermo-gravimetric (TGA-DTG), ii) structural (XRD, FTIR-ATR), iii) morpho-compositional (SEM/EDS) and, most importantly, iv) biological cytotoxicity assays of fibres-derived chars, clearly indicated that luffa-fibres are the safest (>95% cell-survival) to be considered for bioceramic porous-orthopaedic-implants. Further, as exposed by nano-CT, the high temperature pyrolysis of luffa-fibres led to 3D interconnected channels inside the products, which allows a suitable vascularization and osteointegration. The topographic reconstruction of channels-inside-surface revealed a secondary 3D network of micro-pores. Along with the mechanical features, the novel bioceramic porous structures stand as reliable bone-repair alternatives.

The influence of the partial substitution of Fe by Si and thermal treatments on the structural, magnetic and magnetostrictive properties of the Fe67.5Pd30.5Si2 rapidly solidified ribbons has been investigated. A remarkable decrease in the martensite transformation temperature, with similar to 65 K lower than that of the Fe-Pd archetype alloy, is observed in the as-prepared ribbons. The thermal treatments shift the martensite transformation temperatures upward, with approximately 13 K for the higher thermal treatment. Also, these induce an improvement in the crystallinity in these ribbons with high texture and an increase in the crystallite size as a result of reducing the internal defects and stress. The thermodynamic considerations discussed in the frame of the Clapeyron-Clausius relation by using the calorimetric and thermomagnetic measurements (up to 7 T) reveal a weak influence of the magnetic fields on the martensitic transformation temperatures (similar to 0.5 K/T). The magnetostriction decrease with temperature under small magnetic fields was discussed, beside an unusual behaviour in the technically saturated domain. This behaviour is based on the coexistence of the ordinary and forced magnetostrictions, the last one increasing faster with the temperature decreasing.

A novel hybrid composite of conductive poly(methylene blue) (PMB) and carbon nanotubes (CNT) was prepared for the detection of 5-aminosalicylic acid (5-ASA). Electrosynthesis of PMB with glassy carbon electrode (GCE) or with carbon nanotube modified GCE was done in ethaline deep eutectic solvent of choline chloride mixed with ethylene glycol and a 10% v/v aqueous solution. Different sensor architectures were evaluated in a broad range of pH values in a Britton-Robinson (BR) buffer using electrochemical techniques, chronoamperometry (CA), and differential pulse voltammetry (DPV), to determine the optimum sensor configuration for 5-ASA sensing. Under optimal conditions, the best analytical performance was obtained with CNT/PMBDES/GCE in 0.04 M BR buffer pH 7.0 in the range 5-100 mu M 5-ASA using the DPV method, with an excellent sensitivity of 9.84 mu A cm(-2) mu M-1 (4.9 % RSD, n = 5) and a detection limit (LOD) (3 sigma/slope) of 7.7 nM, outclassing most similar sensors found in the literature. The sensitivity of the same sensor obtained in CA (1.33 mu A cm(-2) mu M-1) under optimal conditions (pH 7.0, E-app = +0.40 V) was lower than that obtained by DPV. Simultaneous detection of 5-ASA and its analogue, acetaminophen (APAP), was successfully realized, showing a catalytic effect towards the electro-oxidation of both analytes, lowering their oxidation overpotential, and enhancing the oxidation peak currents and peak-to-peak separation as compared with the unmodified electrode. The proposed method is simple, sensitive, easy to apply, and economical for routine analysis.

It is known that iron is found as a trace element in bone tissue, the main inorganic constituent of which is hydroxyapatite. Therefore, iron-doped hydroxyapatite (HApFe) materials could be new alternatives for many biomedical applications. A facile dip coating process was used to elaborate the iron-doped hydroxyapatite (HApFe) nanocomposite coatings. The HApFe suspension used to prepare the coatings was achieved using a co-precipitation method, which was adapted in the laboratory. The quality of the HApFe suspension was assessed through dynamic light scattering (DLS), ultrasonic measurements, and zeta potential values. The hydroxyapatite XRD patterns were observed in the HApFe nanocomposite with no significant shifting of peak positions, thus suggesting that the incorporation of iron did not significantly modify the hydroxyapatite structure. The morphology of the HApFe nanoparticles was evaluated using transmission electron microscopy (TEM). Scanning electron microscopy (SEM) was used in order to investigate the morphologies of HApFe particles and coatings, while their chemical compositions were assessed using energy-dispersive X-ray spectroscopy (EDS). The SEM results suggested that the HApFe consists mainly of spherical nanometric particles and that the surfaces of the coatings are continuous and homogeneous. Additionally, the EDS spectra highlighted the purity of the samples and confirmed the presence of calcium, phosphorous, and iron in the analyzed sample. The in vitro cytotoxicity of the HApFe suspensions and coatings was evidenced using osteoblast cells. The MTT assay showed that both the HApFe suspensions and coatings exhibited biocompatible properties.

Y2O3:Yb(3+)5 at% ceramics have been synthesized by the reactive sintering method using different commercial yttria powders (Alfa-Micro, Alfa-Nano, and ITO-V) as raw materials. It has been shown that all Y(2)O(3)starting powders consist from agglomerates up to 5-7 mu m in size which are formed from 25-60 nm primary particles. High-energy ball milling allows to significantly decreasing the median particle sizeD(50)below 500 nm regardless of the commercial powders used. Sintering experiments indicate that powder mixtures fabricated from Alfa-Nano yttria powders have the highest sintering activity, while (Y0.86La0.09Yb0.05)(2)O(3)ceramics sintered at 1750 degrees C for 10 h are characterized by the highest transmittance of about 45%. Y2O3:Yb(3+)ceramics have been obtained by the reactive sintering at 1750-1825 degrees C using Alfa-Nano Y(2)O(3)powders and La2O3+ZrO(2)as a complex sintering aid. The effects of the sintering temperature on densification processes, microstructure, and optical properties of Y2O3:Yb(3)(+)5 at% ceramics have been studied. It has been shown that Zr(4)(+)ions decrease the grain growth of Y2O3:Yb(3+)ceramics for sintering temperatures 1750-1775 degrees C. Further increasing the sintering temperature was accompanied by a sharp increase of the average grain size of ceramics referred to changes of structure and chemical composition of grain boundaries, as well as their mobility. It has been determined that the optimal sintering temperature to produce high-dense yttria ceramics with transmittance of 79%-83% and average grain size of 8 mu m is 1800 degrees C. Finally, laser emission at similar to 1030.7 nm with a slope efficiency of 10% was obtained with the most transparent Y2O3:Yb(3+)5 at% ceramics sintered.