National Institute Of Materials Physics - Romania

SiGe-SiO2-based structures present high interest for their high photosensitivity from visible to short-wavelength infrared. Herein, two postdeposition annealing procedures, that is, rapid thermal annealing (RTA) and rapid-like furnace annealing (FA), are compared. Both RTA and FA are performed at 600 degrees C for 1 min for SiGe nanocrystals (NCs) formation in SiO2 matrix in Si/SiO2/SiGe/SiO2 structures deposited by magnetron sputtering. The FA imitates RTA resulting in enhanced spectral response. X-ray diffraction, transmission electron microscopy, and Raman spectroscopy are carried out showing Ge-rich SiGe NCs with 11.3 +/- 1.2 nm size for RTA and 9.4 +/- 0.8 nm for FA. Photocurrent spectra for both structures show several peaks that are annealing dependent. The photocurrent intensity for FA samples is approximate to 7 times higher than RTA samples while cutoff wavelengths are slightly different, that is, 1365 nm for FA and 1375 nm for RTA. The FA structures show (at -1.5 V) over 4 A W-1 responsivity at 730 nm, 6.4 x 10(7) Jones detectivity at 735 nm, and 2.2 x 10(7) Jones at about 1210 nm. FA structures contain small SiGe NCs with incorporated residual strain, while RTA ones are formed of columnar SiGe NCs separated by SiGeOx amorphous regions and show increased tensile strain in the SiGe.

Plastics are indispensable materials for packaging and many products from our daily life, and their recycling is essential to ensure a circular economy. In this study, -SO3H-modified, Ti3C2-MXene was used as a recoverable solid acid catalyst for upcycling of polyethylene terephthalate (PET) to terephthalic acid (TPA) and ethylene glycol by hydrolysis. For the grafting of -SO3H groups to the Ti3C2Tx surface (where T-x represents the surface moieties, such as -OH or -O), sulfonation with an aryl diazonium salt obtained from sulfanilic acid was employed. X-ray photoelectron and Fourier transform infrared spectroscopy analyses provided a direct indication that sulfonation of the Ti3C2Tx was successfully performed, while X-ray diffraction and transmission electron microscopy analyses evidence the presence of -SO3H groups between the Ti3C2Tx layers due to the increases of the interlayer spacing through the intercalation of functional groups. The higher the concentration of acid groups, the higher the interlayer spacing. The depolymerization of PET in water occurred with a very good isolated yield in TPA (99%) for the MXene with the highest amount of sulfonic acid groups. We conclude that the acidity is mandatory to perform the hydrolysis reaction, in agreement with the acidity measurements, which show that the MXenes modified with the highest amount of derived sulfonic acids are the most active. Nevertheless, the accessibility to the acidic sites is a key factor that promotes the 2D acid-modified MXene materials as important catalysts for PET upcycling to TPA.

The present study aims to describe the role of the grain size on the properties of submicron- and nano-structured Ba0.8Sr0.2TiO3 (BST) ceramics. Dense (1 - 2% porosity) ceramics with average grain sizes in the range of (77 234) nm were consolidated under different spark plasma sintering conditions starting from nanopowders with a mean particle size of 70 nm, synthesized via the acetate variant of the sol-gel method. The structural analysis based on XRD data revealed a mixture of cubic and tetragonal modifications at room temperature for the precursor powders and for all the investigated ceramics. The structural heterogeneity of the individual ceramic grains with coexistence of cubic and tetragonal polymorphs was confirmed by HR-TEM investigations. Accordingly, a "brick-wall" model with cubic grain boundary regions and tetragonal grain cores is proposed. By increasing the grain size, from 77 to 234 nm, a decrease of the phase transitions diffuseness accompanied by an increase of the permittivity maxima (from 650 to 4500) and dielectric losses (from 5 to 7.5%, at 100 Hz), was detected by broadband dielectric spectroscopy. No variation of the Curie temperature in the investigated Ba0.8Sr0.2TiO3 ceramics was detected, unlike typically reported for BaTiO3 ceramics with similar grain sizes. The Curie-Weiss temperature and the Curie constant decrease when grain size is diminished, indicating an overall reduction of the ferroelectric active volume, as a scaling effect. The ferroelectric switching was demonstrated for all the selected fine-grained BST ceramics, either at nanoscale or macroscopically, with an increased ferroelectric character for the coarser submicron-structured ceramics, with respect to the nanocrystalline one. The observed properties of the fine-grained Ba0.8Sr0.2TiO3 ceramics are explained in the frame of multiphase coexistence and ferroelectricity "dilution" due to the increasing role of non-ferroelectric grain boundaries when reducing grain size and complete the knowledge on the scale-dependent properties of dense fine-grained BaTiO3-based ceramics.

We investigate the transport and energy spectrum properties of a three-dimensional high-order topological structure formed by stacking two-dimensional square diatomic Chern insulator lattices. Electron-hole symmetry and the energy spectrum degeneracy at individual points in the semimetallic phase are proven to be due to chiral and antiunitary symmetries in the periodic system. Additionally, we explore the influence of boundary conditions in a slab system with varying surface atom connectivity, and we demonstrate analytically the presence of zero-energy surface states in specific configurations. Moreover, we describe the emergence of two chiral hinge states driven by a perpendicular phase in the nanowire geometry. Next, the quantum Hall resistance is computed in the cross-configuration of a four-lead device. In this paper, we demonstrate that the trajectories of hinge states, determined by the number of layers in parallelepiped finite structure, give rise to fractional Hall plateaus.

Magneto-optical measurements enable the identification of Fe2+ and Fe3+ in the R and S blocks of BaFe12O19 Mhexaferrite powder obtained by sol -gel processing, followed by thermal annealing at 900 C for 3 hours. The ferromagnetic phase is evidenced by the spin-majority configuration (Fe3+) due to their unpaired electrons between d -d orbitals, while the Fe2+ in the low spin possesses diamagnetic behavior strongly dependent on the surrounded crystal field. Additionally, the irradiation with gamma rays changes the ratio between Fe2+/Fe3+, mainly on the surface of BaFe12O19 nanocrystals. These changes were confirmed by X-ray Photoelectron Spectroscopy measurements, in which the concentration of Fe2+ increased from 69% to 82%, while the one of Fe3+ decreased from 31% to 18%. he thermoluminescent measurements reveal the same changes of Fe3+ in Fe2+ by electron capturing during irradiation, which is released as a red emission after recombination processes. The changes are explained by the increasing of some Fe-O bonds along the c-axis, mainly due to breaking a part of these bonds. The X-ray analysis confirms the changing of the parameters for the BaFe12O19 hexagonal structure.

Considering the increasing need for sustainable and economical energy storage solutions, the integration of layered materials such as MoS2 into these systems represents an important step toward enhancing energy sustainability and efficiency. Exploring environmentally responsible fabrication techniques, this study assesses wrinkled MoS2 thin films synthesized from distinct Mo and MoS2 targets, followed by sulfurization conducted in a graphite box. We utilized magnetron sputtering to deposit precursor Mo and MoS2 films on Si substrates, achieving thicknesses below 20 nm. This novel approach decreases sulfur by up to tenfold during sulfurization due to the confined space technique, contributing also to avoiding the formation of toxic gases such as SO2 or the necessity of using H2S, aligning with sustainable materials development. Thinner MoS2 layers were obtained post-sulfurization from the MoS2 precursors, as shown by X-ray reflectometry. Raman spectroscopy and grazing X-ray diffraction analyses confirmed the amorphous nature of the as-deposited films. Post-sulfurization, both types of films exhibited crystalline hexagonal MoS2 phases, with the sulfurized Mo showing a polycrystalline nature with a (100) orientation and sulfurized MoS2 displaying a (00L) preferred orientation. The X-ray photoelectron spectroscopy results supported a Mo:S ratio of 1:2 on the surface of the films obtained using the MoS2 precursor films, confirming the stoichiometry obtained by means of energy dispersive X-ray spectroscopy. Scanning electron microscopy and atomic force microscopy images revealed micrometer-sized clusters potentially formed during rapid cooling post-sulfurization, with an increased average roughness. These results open the way for the further exploration of wrinkled MoS2 thin films in advanced energy storage technologies.

The precipitation-hardenable nickel-based superalloy Rene 41 exhibits remarkable mechanical characteristics and high corrosion resistance at high temperatures, properties that allow it to be used in high-end applications. This research paper presents findings on the influence of thermal shocks on its microstructure, hardness, and thermal diffusivity at temperatures between 700 and 1000 degrees C. Solar energy was used for cyclic thermal shock tests. The samples were characterized using microhardness measurements, optical microscopic analysis, scanning electron microscopy coupled with EDS elemental chemical analysis, X-ray diffraction, and flash thermal diffusivity measurements. Structural transformations and the variation of properties were observed with an increase in the number of shocks applied at the same temperature and with temperature variation for the same number of thermal shocks.